About Structural Adhesives
More
Steel Adhesive-Grip Female-Threaded Anchors for Concrete
A zinc plating provides corrosion resistance in wet environments. Use these anchors for permanent, high-strength anchoring where vibration is present. To install, fill a clean, drilled hole half full with epoxy adhesive, then insert the anchor until it's flush with the surface. Pull-out strength values are 25% of the ultimate values.
For technical drawings and 3-D models, click on a part number.
| Thread Size  | Lg. | Drill Bit Size | Min. Installation Dp. | Dia. | Thread Dp. | Pull-Out Strength, lbs. | Tested In | Each | |
Zinc-Plated Steel | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 1/4"-20 | 1 5/8" | 5/16" | 1 3/4" | 5/16" | 1/2" | 720 | 3,000 psi Concrete | 000000000 | 00000 |
| 5/16"-18 | 2 3/8" | 7/16" | 2 3/4" | 7/16" | 3/4" | 1,800 | 3,000 psi Concrete | 000000000 | 0000 |
| 3/8"-16 | 2 3/4" | 1/2" | 3 1/4" | 1/2" | 1" | 2,300 | 3,000 psi Concrete | 000000000 | 00000 |
| 1/2"-13 | 3 3/4" | 5/8" | 4 1/8" | 5/8" | 1" | 3,200 | 3,000 psi Concrete | 000000000 | 00000 |
| 5/8"-11 | 5 3/4" | 7/8" | 6 1/4" | 7/8" | 1 1/2" | 6,500 | 3,000 psi Concrete | 000000000 | 00000 |
| 3/4"-10 | 6 1/2" | 1" | 7 1/2" | 1" | 1 1/2" | 9,000 | 3,000 psi Concrete | 000000000 | 00000 |
| 1"-8 | 8 1/2" | 1 1/2" | 9 1/2" | 1 1/2" | 2" | 12,700 | 3,000 psi Concrete | 000000000 | 000000 |
Stainless Steel Adhesive-Grip Female-Threaded Anchors for Concrete
These 316 stainless steel anchors have excellent resistance to chemicals and salt water and may be mildly magnetic. Use them for permanent, high-strength anchoring where vibration is present. To install, fill a clean, drilled hole half full with epoxy adhesive, then insert the anchor until it's flush with the surface. Pull-out strength values are 25% of the ultimate values.
For technical drawings and 3-D models, click on a part number.
| Thread Size | Lg. | Drill Bit Size | Min. Installation Dp. | Dia. | Thread Dp. | Pull-Out Strength, lbs. | Tested In | Each | |
316 Stainless Steel | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 1/4"-20 | 1 5/8" | 5/16" | 1 3/4" | 5/16" | 1/2" | 720 | 3,000 psi Concrete | 000000000 | 000000 |
| 5/16"-18 | 2 3/8" | 7/16" | 2 3/4" | 7/16" | 3/4" | 1,800 | 3,000 psi Concrete | 000000000 | 00000 |
| 3/8"-16 | 2 3/4" | 1/2" | 3 1/4" | 1/2" | 1" | 2,300 | 3,000 psi Concrete | 000000000 | 00000 |
| 1/2"-13 | 3 3/4" | 5/8" | 4 1/8" | 5/8" | 1" | 3,200 | 3,000 psi Concrete | 000000000 | 00000 |
| 5/8"-11 | 5 3/4" | 7/8" | 6 1/4" | 7/8" | 1 1/2" | 6,500 | 3,000 psi Concrete | 000000000 | 000000 |
| 3/4"-10 | 6 1/2" | 1" | 7 1/2" | 1" | 1 1/2" | 9,000 | 3,000 psi Concrete | 000000000 | 000000 |
| 1"-8 | 8 1/2" | 1 1/2" | 9 1/2" | 1 1/2" | 2" | 12,700 | 3,000 psi Concrete | 000000000 | 000000 |
Adhesive Anchor Screen Tubes for Hollow Block and Brick
Used with adhesive in bricks and hollow blocks, such as cinder blocks, these mesh tubes create a stronger hold for rods and studs than other anchors. To install, first fill tubes with adhesive (sold separately) and press them into a drilled hole. Hold tubes in place by pressing the tab against your block, and insert a rod into them. The rod will push the adhesive out of the mesh screen, forming a plug that keeps the rod in place once the adhesive dries.
For technical drawings and 3-D models, click on a part number.
| Container Size, fl. oz. | Begins to Harden | Reaches Full Strength | No. of 1/2" Dia. Rods Set at 4 1/2" Installation Dp. | Ultimate Pull-Out Strength (in 4,000 psi Concrete) | Mix Ratio | Consistency | Temp. Range, °F | Color | Each | |
| 9.5 | 5 min. @ 70° F | 45 min. | 25 in 9/16" dia. hole | 10,900 lbs.—3/8" threaded rod dia. × 3 1/2" installation dp. 17,100 lbs.—1/2" threaded rod dia. × 4 1/2" installation dp. 26,500 lbs.—5/8" threaded rod dia. × 5 5/8" installation dp. 29,500 lbs.—3/4" threaded rod dia. × 6 3/4" installation dp. 44,500 lbs.—7/8" threaded rod dia. × 7 7/8" installation dp. 48,000 lbs.—1" threaded rod dia. × 9" installation dp. 56,500 lbs.—1 1/4" threaded rod dia. × 11 1/4" installation dp. | 10:1 | Paste | 15° to 110° | Gray | 0000000 | 000000 |
Submersible Anchoring Adhesives for Concrete
When concrete is saturated with or submerged in water, use these epoxies to permanently set threaded rods, studs, and rebar. They form a weather-resistant chemical bond that seals out moisture and resists vibration and dynamic loads better than mechanical anchors. Warning: Allowable pull-out strength is 25% of ultimate values or less, as required by building authorities. Use a mixer nozzle and dispensing gun (dispensing gun sold separately) to simultaneously mix and dispense adhesive.
| Container Size, fl. oz. | Begins to Harden | Reaches Full Strength | No. of 1/2" Dia. Rods Set at 4 1/2" Installation Dp. | Ultimate Pull-Out Strength (in 4,000 psi Concrete) | Mix Ratio | Consistency | Temp. Range, °F | Color | Each | |
| 9.5 | 5 min. @ 70° F | 45 min. | 25 in 9/16" dia. hole | 10,900 lbs.—3/8" threaded rod dia. × 3 1/2" installation dp. 17,100 lbs.—1/2" threaded rod dia. × 4 1/2" installation dp. 26,500 lbs.—5/8" threaded rod dia. × 5 5/8" installation dp. 29,500 lbs.—3/4" threaded rod dia. × 6 3/4" installation dp. 44,500 lbs.—7/8" threaded rod dia. × 7 7/8" installation dp. 48,000 lbs.—1" threaded rod dia. × 9" installation dp. 56,500 lbs.—1 1/4" threaded rod dia. × 11 1/4" installation dp. | 10:1 | Paste | 15° to 110° | Gray | 0000000 | 000000 |
| 28 | 5 min. @ 70° F | 45 min. | 75 in 9/16" dia. hole | 10,900 lbs. —3/8" Threaded Rod Dia. × 3 3/8" Insulation Dp. 17,100 lbs.—1/2" threaded rod dia. × 4 1/2" installation dp. 26,500 lbs.—5/8" threaded rod dia. × 5 5/8" installation dp. 29,500 lbs.—3/4" threaded rod dia. × 6 3/4" installation dp. 44,500 lbs.—7/8" threaded rod dia. × 7 7/8" installation dp. 48,000 lbs.—1" threaded rod dia. × 9" installation dp. 56,500 lbs.—1 1/4" threaded rod dia. × 11 1/4" installation dp. | 10:1 | Paste | 15° to 110° | Gray | 0000000 | 00000 |