Fasten hard-to-bond plastics, such as polypropylene and polyethylene, with these adhesives. They bond dissimilar materials. Epoxies are the strongest and most weather- and chemical-resistant structural adhesives. Choose an adhesive that hardens quickly for fast repairs, or one that hardens slowly to allow more time for positioning.

The size listed is the combined total of the two parts. Use cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.

With excellent resistance to corrosive chemicals and salt water, these epoxies work in tough conditions. Epoxies are the strongest structural adhesives. Choose an adhesive that hardens quickly for fast repairs, or one that hardens slowly to allow more time for positioning.

The size listed is the combined total of the two parts. Use cartridges with a dispensing gun and mixer nozzle to simultaneously mix and dispense adhesives.

E-120HP resists acetone, fuel, and oil. It bonds dissimilar materials and withstands rapid changes in temperature.

Accommodate joint movement with these adhesives that remain pliable when cured. Also known as super glue. Use an accelerator (sold separately) to shorten the time it takes the adhesive to reach full strength.

Mixed with rubber for better impact resistance than standard instant-bond adhesives, these adhesives form strong, resilient bonds. Also known as super glue. Use an accelerator (sold separately) to shorten the time it takes the adhesive to reach full strength.

Form bonds in 5 seconds or less with these adhesives, also known as super glue. Use an accelerator (sold separately) to shorten the time it takes to reach full strength.

Make strong, instant bonds on a variety of materials—but not your skin. Also known as super glue. Use an accelerator (sold separately) to shorten the time it takes the adhesive to reach full strength.

Use these thick gels, also known as super glue, on vertical surfaces or to fill gaps between parts. Use an accelerator (sold separately) to shorten the time it takes the adhesive to reach full strength.

Dispense adhesives in cartridges with a standard caulk gun.

These adhesives stay pliable for flexible bonds that resist cracking. For easy positioning, they begin to harden only when exposed to light.

1700A257 and 2454N1 fluoresce under UV light for easy inspection.

For easy positioning, these adhesives begin to harden only when exposed to light.

Thin liquids flow to fill small gaps between close-fitting parts.

Spray a thin, uniform coat of adhesive on one or both surfaces, air dry, and then bring together to form strong bonds.

Adhesives that cannot be sold to California exceed local regulatory limits on VOCs (volatile organic compounds).

Form bonds with twice the strength of our other spray adhesives. Spray a thin, uniform coat of adhesive on one or both surfaces, air dry, and then bring together to adhere.

Adhesives that cannot be sold to California exceed local regulatory limits on VOCs (volatile organic compounds).

Apply these adhesives on two surfaces, air dry, and then bring together to bond.

Adhesives that cannot be sold to the regions listed exceed local regulatory limits on VOCs (volatile organic compounds).

These adhesives resist temperatures up to 500° F, as well as chemicals, fuels, grease, and water. Apply them to both surfaces, air dry, and then bring together to bond. Heat to 300° F to reach full strength. They cannot be sold to the regions listed because these adhesives exceed local regulatory limits on VOCs (volatile organic compounds).

The 3M VHB adhesive on these rolls offers a strong hold that can replace rivets, spot welds, and other permanent fasteners. Also known as adhesive transfer tape, these rolls have a thin film of pressure-sensitive glue on a peel-away liner. They’re more conformable than tape with adhesive on both sides.

F9473PC are our thickest option, so they’re the best at adhering to gaps and crevices on uneven surfaces.

Rolls that meet ASTM E595, a standard used by NASA, release almost no volatile emissions that could damage sensitive electronics, even in a vacuum.

Certificates with a traceable lot number and product shelf life are available for these products. Download certificates from ORDER HISTORY after your order ships.

Temporarily stabilize objects on flat surfaces with this clear adhesive gel. It removes cleanly from most surfaces with a twist, and it won't dry out so it can be used again.

Pull off a small piece of putty and stick lightweight objects to your surface. It removes without leaving stains or residue on most surfaces and is reusable.

These small tabs of pressure-sensitive adhesive offer convenient, no-mess bonding.

Bond stone and glass to drywall, treated lumber, and subfloors with these adhesives.

Non-sag adhesives won't drip from vertical and overhead surfaces.

Adhesives that cannot be sold to the regions listed are restricted by labeling and reporting requirements in Canada, and by local regulatory limits on VOCs (volatile organic compounds) in the states listed.

For insulation joints on ovens and furnaces, this cement has excellent temperature resistance.

An alternative to solder, these flexible, silver-filled adhesives accommodate joint movement. Use them to bond electrical components and repair circuits.

Epoxy adhesives are two-part adhesives that need to be mixed together. The size listed is the combined total of the two parts.

When heated, these glue sticks melt and quickly begin to harden. Use them to seal packaging and form other low- to medium-strength bonds. 3M glue sticks work only with 3M glue guns.

Adhesives that take longer to harden are suited for applications that require some repositioning, because the longer open times allow for more adjustment. For high-volume applications, adhesives with a lower viscosity flow faster than other hot-melt adhesives.

Remaining flexible after curing, these glue sticks accommodate joint movement. All are FDA compliant 21 CFR 175.105 and suitable for food packaging.

The polyurethane glue in these cartridges has nearly twice the shear strength of other hot-melt adhesives.