We will reply to your message within an hour.
More
Fine threads give you precise control.
These metric set screws have a rolling ball that swivels 360° to minimize surface damage and allow for slight adjustments without loosening the screw.
A rolling ball swivels 360° to minimize surface damage and allow for slight adjustments without loosening the screw.
Stainless steel set screws have excellent corrosion resistance in most environments.
The tip is narrow to pass through threaded holes.
A wide tip provides more gripping power than standard swivel-tip set screws. To use, remove the tip, thread the screw through the hole, and attach the tip on the other side.
A low-profile flat-faced ball tip allows these metric set screw to be used in low-clearance applications.
These set screws have a low-profile flat-faced ball tip for use in low-clearance applications.
A wide tip provides more gripping power than standard swivel-tip thumb screws. To use, remove the tip, thread the screw through the hole, and attach the tip on the other side.
For maximum contact with angled and uneven surfaces, the tip swivels in all directions. The tip is narrow so it will fit through threaded holes.
A large swivel angle allows these thumb screws to make better contact with angled and uneven surfaces than nonremovable swivel-tip thumb screws.
Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel.
Made of yellow zinc-plated steel, these metric leveling mounts are more corrosion resistant than nickel-plated steel leveling mounts.
Black-oxide steel has a dull shine for areas where appearance is a concern.
Nickel-plated steel has some corrosion resistance.
An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.
Made of 303 stainless steel, these metric mounts resist corrosion from water and most chemicals.
Made of 303/304 stainless steel, these mounts resist corrosion from water and most chemicals.
Made entirely of 316 stainless steel, these metric mounts have superior corrosion resistance.
Made entirely of 316 stainless steel, these mounts have superior corrosion resistance.
Broader, stronger threads enable faster adjustments and higher load capacities than standard V-shaped threads.
Well-suited to damp environments, these mounts have a stainless steel stud and nut for corrosion resistance.
Well-suited to damp environments, these metric mounts have a stainless steel stud and nut for corrosion resistance.
Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary.
Punch-out holes in the base let you bolt down these metric mounts to keep your equipment stationary.
An offset mounting hole allows for installation without moving your machine.
Made entirely of 316 stainless steel, these mounts are our most resistant to corrosion from chemicals, solvents, and water.
Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals.
Well-suited to damp environments, these mounts have a stainless steel nut for excellent corrosion resistance.
Ready for installation on the bottom of machines and equipment without feet, these mounts come with their own bracket.
These mounts have a cushion on top to provide padding between your furniture and the mount.
Use these metric mounts on heavy machines and equipment.
Use these mounts on heavy machines and equipment.
A hex nut at the base of the stud allows for easy height adjustment.
Made entirely of plastic, these mounts are resistant to oil and won't scratch your mounting surface.
A shield on the stud prevents dirt accumulation on the threads and provides a finished appearance.
Able to withstand temperatures up to 350° F, these have the highest maximum temperature of our plastic mounts.
Protect surfaces from scratches and wear.
Meant for light duty applications, these mounts are not rated for capacity.
Often used on wobbly tables, these mounts automatically adjust up to 5/16" to compensate for uneven floors.
Install these mounts on machines without feet.
These mounts have fine threads that give you precise leveling control.
Choose from mounts that support 3,000 to 110,000 lbs. for heavy machinery.
Adjust the swivels on these mounts to level equipment on uneven surfaces for protection during earthquakes.
Designed for use in sanitary and food processing areas, these mounts level tanks and machinery on uneven floors and create space to clean underneath.
A two-piece design simplifies installation and requires less clearance than one-piece mounts.
Higher deflection ratings translate to greater vibration and shock isolation than our other vibration-damping leveling mounts.
All-stainless steel construction stands up to water and chemicals and won't rust or corrode.
A two-piece design requires less clearance than one-piece mounts and simplifies installation—raise your machine just enough to slide the base underneath, then insert the stud from above.
Bolt these mounts down to keep your equipment stationary.
Higher deflection ratings translate to greater vibration and shock isolation.
Thread these mounts into machinery to level them on uneven floors in sanitary environments such as food-processing areas.
Choose from mounts that support 3,000 to 30,000 lbs. for heavy machinery.
Insert these adjustable mounts into tube ends to level your equipment in a single step.
Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.
Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.
Combine with an externally threaded acme nut to create a custom flange nut.
Also known as trapezoidal-thread lead screws and nuts.
Found in hand-powered clamps, vises, grates, doors, and work tables, lead screws and nuts have broad, square threads that are well suited for quick assembly, high clamping forces, and lifting and lowering heavy objects.
These metric lead screws and nuts have broad, square threads that are well suited for quick assembly, high clamping forces, and lifting and lowering heavy objects. They're commonly found in hand-powered clamps, vises, grates, doors, and work tables.
A set of ball bearings reduces friction and secures the end of a ball or lead screw.
A set of ball bearings reduces friction and secures the end of a metric ball or lead screw.
Also known as single-start ball screws and nuts, these have a single thread that runs the length of the screw. They operate with more torque than fast-travel ball screws and nuts.
Keep your ball screw spinning without the ball nut damaging your system. When the ball nut reaches the stop pin at either end of the ball screw, it disengages and begins to idle.
Multiple thread channels (also known as thread starts) create faster linear travel than ball screws with a single thread start.
Thread these one-piece collars onto an Acme lead screw.
Mount these two-piece collars anywhere on an Acme lead screw without removing components.
Install these threaded collars on a metric lead screw to separate and position components, or use them as an end stop to limit travel.
A crisscross thread pattern allows you to drive the nut back and forth without changing the lead screw's direction of rotation. When the nut reaches one end of the lead screw, it changes direction and travels back to the other end.
Precision ground to create more points of contact, these roller screws and nuts are highly accurate and handle much higher loads than ball screws and nuts of the same size.
Install these nuts on a rotary shaft to create a linear positioning system without a lead screw. Instead of threads, a set of angled ball bearings drives the nut along a shaft as it spins.
Replace worn screws or customize your clamps.
From one compact system, transmit linear or rotary motion or both at once (sometimes called spiral motion). Because of these different motions, these ball screw/splines and bearings create efficient, fluid movements in complex automated applications, such as pick-and-place robots.
With an included controller and an integrated stepper motor, these slides are a complete precision motion control system.
Add your own stepper motor and controller to precisely move the ball screw and carriage smoothly at high speeds, like a head on an inkjet printer.
With PTFE sleeve bearings and a low-friction ball screw, these slides don’t require the mess and maintenance of lubrication but still give you precise positioning anywhere along the length of their stroke.