Air Exhauster Blowers | McMaster-Carr

Filter by

Voltage

Electrical Phase

Power Source

Housing Material

DFARS Compliance

Minimum Temperature

Maximum Temperature

RoHS Compliance

Overall Width

Horsepower

Overall Height

Maximum Pressure

Inverter Rated

Certification

Maximum Flow Rate @ Pressure

Outlet Pipe Size

Full Load Current @ Voltage

Inlet Thread Type

Inlet Pipe Size

Muffler Location

REACH Compliance

Volume (Sound)

Outlet Thread Type

Forward

How can we improve?

99 Products

About Sound Levels

Measured in decibels (dB), volume ratings indicate how much noise equipment makes. Some common volume levels include a whisper @ 20 dB, a refrigerator @ 40 dB, a conversation @ 60 dB, and a light machine shop @ 90 dB. OSHA recommends hearing protection for exposure to 80 dB and greater.

About Air Compressors

High-Flow Low-Pressure Compressed Air Blowers

Also known as regenerative blowers, use these to produce high-flow compressed air with low pressure or vacuum to operate pump drives, lift tables, and conveying systems. Compressed air blowers are also used for drying, exhausting, and aeration.

Air circulates inside the blower housing to compress air, which generates pressure or vacuum. Single-stage blowers circulate air once and then exhaust. Two-stage blowers circulate air twice and then exhaust, creating higher pressure or vacuum than single-stage blowers with the same horsepower.

Inverter-rated blowers have a motor that can run at slow speeds without overheating, so they can be used with a motor speed control (variable frequency drive).

For technical drawings and 3-D models, click on a part number.

Single Stage

Single Stage Blower

Blowers
						Overall				Pipe Size				Air-Intake Filters		Relief Valves
Maximum Pressure	Max. Flow Rate @ psi	Vacuum Rating	hp	Full Load Current	Vol.	Lg.	Wd.	Ht.	Temp. Range, °F	Inlet	Outlet		Each		Each		Each
Single Phase, 120/208/230V AC
NPT Female Inlet and Outlet
1 psi 29 in. of H₂O	27 cfm @ 0	1.9 in. of Hg 27 in. of H₂O	1/8	2.3 A @ 115 V AC 1.2 A @ 208 V AC 1.2 A @ 230 V AC	57 dBA	9"	8"	9"	32° to 100°	1	1	0000000	0000000	00000000	0000000	00000000	0000000
1 psi 39 in. of H₂O	42 cfm @ 0	2.6 in. of Hg 35 in. of H₂O	1/3	3.8 A @ 115 V AC 2.0 A @ 208 V AC 1.9 A @ 230 V AC	63 dBA	10"	9"	9"	32° to 100°	1	1	0000000	00000000	00000000	000000	00000000	000000
1 psi 52 in. of H₂O	156 cfm @ 0	3.8 in. of Hg 51 in. of H₂O	2	19.7 A @ 115 V AC 10.6 A @ 208 V AC 9.9 A @ 230 V AC	71 dB	14"	13"	13"	5° to 100°	2	2	0000000	00000000	000000	00	0000000	000000
2 psi 42 in. of H₂O	52 cfm @ 0	3.0 in of Hg 40 in. of H₂O	1/2	6.0 A @ 115 V AC 3.2 A @ 208 V AC 3.0 A @ 230 V AC	68 dBA	13"	10"	10"	32° to 100°	1 1/4	1 1/4	0000000	00000000	00000000	000000	00000000	000000
2 psi 52 in. of H₂O	92 cfm @ 0	3.5 in. of Hg 48 in. of H₂O	1	9.8 A @ 115 V AC 5.2 A @ 208 V AC 4.9 A @ 230 V AC	68 dBA	13"	11"	12"	32° to 100°	1 1/2	1 1/2	0000000	00000000	00000000	000000	00000000	000000
2 psi 65 in. of H₂O	127 cfm @ 0	4.4 in. of Hg 60 in. of H₂O	1 1/2	17.5 A @ 115 V AC 10.0 A @ 208 V AC 9.0 A @ 230 V AC	74 dBA	16"	13"	14"	32° to 100°	1 1/2	1 1/2	0000000	00000000	00000000	000000	00000000	000000
Single Phase, 120/230V AC
BSPP Female Inlet and Outlet
2 psi 56 in. of H₂O	57 cfm @ 0	3.8 in. of Hg 52 in. of H₂O	1/2	6.0 A @ 115 V AC 3.0 A @ 230 V AC	56 dBA	10"	10"	10"	5° to 100°	1 1/4	1 1/4	0000000	00000000	000000	00	000000	00
3 psi 76 in. of H₂O	102 cfm @ 0	5.3 in. of Hg 72 in. of H₂O	1 1/2	14.0 A @ 115 V AC 7.0 A @ 230 V AC	64 dBA	12"	11"	12"	5° to 100°	1 1/2	1 1/2	0000000	00000000	000000	00	000000	00
NPT Female Inlet and Outlet
3 psi 72 in. of H₂O	148 cfm @ 0	5.3 in. of Hg 72 in. of H₂O	2 1/4	24.0 A @ 115 V AC 12.0 A @ 230 V AC	70 dBA	14"	13"	13"	5° to 100°	2	2	0000000	00000000	000000	00	000000	00
Three Phase, 190/230/380/460V AC (Inverter Rated)
NPT Female Inlet and Outlet
2 psi 56 in. of H₂O	103 cfm @ 0	4.1 in. of Hg 56 in. of H₂O	1	4.4 A @ 190 V AC 3.7 A @ 230 V AC 2.2 A @ 380 V AC 2.1 A @ 460 V AC	64 dBA	11"	11"	12"	32° to 100°	1 1/2	1 1/2	0000000	00000000	000000	00	000000	00
3 psi 79 in. of H₂O	150 cfm @ 0	6.5 in. of Hg 88 in. of H₂O	2 3/4	7.5 A @ 190 V AC 7.3 A @ 230 V AC 4.3 A @ 380 V AC 4.4 A @ 460 V AC	70 dBA	14"	13"	15"	32° to 100°	2	2	0000000	00000000	000000	00	000000	00
3 psi 92 in. of H₂O	221 cfm @ 0	7.1 in. of Hg 96 in. of H₂O	4 1/2	12.5 A @ 190 V AC 12.6 A @ 230 V AC 7.2 A @ 380 V AC 7.3 A @ 460 V AC	72 dBA	15"	15"	17"	32° to 100°	2	2	0000000	00000000	000000	00	000000	00
4 psi 116 in. of H₂O	150 cfm @ 0	7.7 in. of Hg 104 in. of H₂O	3 1/4	9.7 A @ 190 V AC 10.3 A @ 230 V AC 5.6 A @ 380 V AC 6.0 A @ 460 V AC	70 dBA	14"	13"	15"	32° to 100°	2	2	0000000	00000000	000000	00	000000	00
Three Phase, 208/230/460V AC
NPT Female Inlet and Outlet
2 psi 43 in. of H₂O	53 cfm @ 0	2.9 in. of Hg 40 in. of H₂O	1/2	2.0 A @ 208 V AC 2.0 A @ 230 V AC 1.0 A @ 460 V AC	68 dBA	11"	10"	10"	32° to 100°	1 1/4	1 1/4	0000000	00000000	00000000	000000	00000000	000000
2 psi 52 in. of H₂O	92 cfm @ 0	3.5 in. of Hg 48 in. of H₂O	1	3.4 A @ 208 V AC 3.2 A @ 230 V AC 1.6 A @ 460 V AC	68 dBA	13"	11"	12"	32° to 100°	1 1/2	1 1/2	0000000	00000000	00000000	000000	00000000	000000
2 psi 65 in. of H₂O	127 cfm @ 0	4.4 in. of Hg 60 in. of H₂O	1 1/2	5.1 A @ 208 V AC 4.9 A @ 230 V AC 2.5 A @ 460 V AC	74 dBA	14"	13"	14"	32° to 100°	1 1/2	1 1/2	0000000	00000000	00000000	000000	00000000	000000
Three Phase, 208/230/460V AC (Inverter Rated)
NPT Female Inlet and Outlet
1 psi 52 in. of H₂O	156 cfm @ 0	3.8 in. of Hg 51 in. of H₂O	2	5.7 A @ 208 V AC 5.7 A @ 230 V AC 2.8 A @ 460 V AC	71 dB	14"	13"	13"	5° to 100°	2	2	0000000	00000000	000000	00	0000000	000000
2 psi 80 in. of H₂O	156 cfm @ 0	6.6 in. of Hg 89 in. of H₂O	3	8.2 A @ 208 V AC 8.3 A @ 230 V AC 4.1 A @ 460 V AC	71 dB	14"	13"	13"	5° to 100°	2	2	0000000	00000000	000000	00	0000000	000000
3 psi 110 in. of H₂O	216 cfm @ 0	8.1 in. of Hg 110 in. of H₂O	5 1/2	14.6 A @ 208 V AC 15.1 A @ 230 V AC 7.5 A @ 460 V AC	74 dB	15"	15"	15"	5° to 100°	2	2	0000000	00000000	000000	00	0000000	000000
4 psi 105 in. of H₂O	207 cfm @ 0	6.5 in. of Hg 88 in. of H₂O	5	13.0 A @ 208 V AC 12.0 A @ 230 V AC 6.0 A @ 460 V AC	72 dBA	19"	15"	15"	32° to 100°	2	2	0000000	00000000	00000000	000000	00000000	000000
4 psi 110 in. of H₂O	265 cfm @ 0	6.6 in. of Hg 90 in. of H₂O	6	16.0 A @ 208 V AC 15.0 A @ 230 V AC 7.5 A @ 460 V AC	79 dBA	17"	17"	18"	32° to 100°	2	2	0000000	00000000	00000000	000000	00000000	000000
4 psi 121 in. of H₂O	294 cfm @ 0	8.9 in. of Hg 121 in. of H₂O	7 1/2	19.8 A @ 208 V AC 19.5 A @ 230 V AC 9.7 A @ 460 V AC	79 dB	15"	17"	18"	5° to 100°	3	3	0000000	00000000	000000	00	0000000	000000
5 psi 125 in. of H₂O	420 cfm @ 0	8.1 in. of Hg 110 in. of H₂O	10	35.0 A @ 208 V AC 29.5 A @ 230 V AC 15.0 A @ 460 V AC	78 dBA	22"	18"	20"	32° to 100°	2 1/2	2 1/2	0000000	00000000	00000000	000000	00000000	000000
Three Phase, 220/275/380/480V AC (Inverter Rated)
BSPP Female Inlet and Outlet
2 psi 64 in. of H₂O	57 cfm @ 0	4.4 in. of Hg 60 in. of H₂O	1/2	2.6 A @ 200 V AC 2.6 A @ 275 V AC 1.5 A @ 380 V AC 1.5 A @ 480 V AC	56 dBA	10"	10"	10"	5° to 100°	1 1/4	1 1/4	0000000	00000000	000000	00	000000	00
Three Phase, 230/460V AC (Inverter Rated)
NPT Female Inlet and Outlet
4 psi 105 in. of H₂O	795 cfm @ 0	7.0 in. of Hg 95 in. of H₂O	18	52.0 A @ 230 V AC 26.0 A @ 460 V AC	79 dBA	29"	18"	20"	32° to 100°	2 1/2	4	0000000	00000000	00000000	000000	00000000	00000000

Two Stage

Two Stage Blower

Blowers
						Overall				Pipe Size				Relief Valves
Maximum Pressure	Max. Flow Rate @ psi	Vacuum Rating	hp	Full Load Current	Vol.	Lg.	Wd.	Ht.	Temp. Range, °F	Inlet	Outlet		Each		Each
Single Phase, 120/208/230V AC
NPT Female Inlet and Outlet
3 psi 98 in. of H₂O	35 cfm @ 0	7.2 in. of Hg 97 in. of H₂O	3/4	8.3 A @ 115 V AC 4.1 A @ 208 V AC 4.2 A @ 230 V AC	64 dB	15"	10"	11"	5° to 100°	3/4	3/4	0000000	000000000	0000000	0000000
4 psi 120 in. of H₂O	35 cfm @ 0	8.1 in. of Hg 110 in. of H₂O	1	9.4 A @ 115 V AC 5.5 A @ 208 V AC 5.0 A @ 230 V AC	64 dB	15"	10"	11"	5° to 100°	3/4	3/4	0000000	00000000	0000000	000000
5 psi 140 in. of H₂O	65 cfm @ 0	11.1 in. of Hg 151 in. of H₂O	2	19.7 A @ 115 V AC 10.6 A @ 208 V AC 9.9 A @ 230 V AC	72 dB	15"	13"	14"	5° to 100°	1 1/4	1 1/4	0000000	00000000	0000000	000000
5 psi 141 in. of H₂O	81 cfm @ 0	11.1 in. of Hg 151 in. of H₂O	3	29.4 A @ 115 V AC 16.6 A @ 208 V AC 14.8 A @ 230 V AC	73 dB	15"	14"	15"	5° to 100°	1 1/4	1 1/4	0000000	00000000	0000000	000000
5 psi 161 in. of H₂O	41 cfm @ 0	10.3 in. of Hg 140 in. of H₂O	1 1/2	14.6 A @ 115 V AC 7.6 A @ 208 V AC 7.3 A @ 230 V AC	69 dB	14"	11"	12"	5° to 100°	1 1/4	1 1/4	0000000	00000000	0000000	000000
Three Phase, 208/230/460V AC (Inverter Rated)
NPT Female Inlet and Outlet
3 psi 98 in. of H₂O	35 cfm @ 0	7.2 in. of Hg 97 in. of H₂O	3/4	2.3 A @ 208 V AC 2.2 A @ 230 V AC 1.3 A @ 460 V AC	64 dB	15"	10"	11"	5° to 100°	3/4	3/4	0000000	00000000	0000000	000000
4 psi 120 in. of H₂O	35 cfm @ 0	8.1 in. of Hg 110 in. of H₂O	1	2.9 A @ 208 V AC 2.9 A @ 230 V AC 1.4 A @ 460 V AC	64 dB	15"	10"	11"	5° to 100°	3/4	3/4	0000000	00000000	0000000	000000
5 psi 140 in. of H₂O	65 cfm @ 0	11.1 in. of Hg 151 in. of H₂O	2	5.8 A @ 208 V AC 5.2 A @ 230 V AC 2.8 A @ 460 V AC	72 dBA	16"	13"	14"	5° to 100°	1 1/4	1 1/4	0000000	00000000	0000000	000000
5 psi 141 in. of H₂O	81 cfm @ 0	11.1 in. of Hg 151 in. of H₂O	3	8.3 A @ 208 V AC 7.4 A @ 230 V AC 4.0 A @ 460 V AC	73 dBA	16"	14"	15"	5° to 100°	1 1/4	1 1/4	0000000	00000000	0000000	000000
5 psi 150 in. of H₂O	129 cfm @ 0	11.8 in. of Hg 160 in. of H₂O	5 1/2	14.6 A @ 208 V AC 15.1 A @ 230 V AC 7.5 A @ 460 V AC	75 dB	18"	17"	19"	5° to 100°	2	2	0000000	00000000	0000000	000000
5 psi 161 in. of H₂O	41 cfm @ 0	10.3 in. of Hg 140 in. of H₂O	1 1/2	4.3 A @ 208 V AC 4.3 A @ 230 V AC 2.1 A @ 460 V AC	69 dB	14"	11"	12"	5° to 100°	1 1/4	1 1/4	0000000	00000000	0000000	000000
6 psi 191 in. of H₂O	65 cfm @ 0	11.1 in. of Hg 151 in. of H₂O	3	8.2 A @ 208 V AC 8.3 A @ 230 V AC 4.1 A @ 460 V AC	73 dB	15"	13"	14"	5° to 100°	1 1/4	1 1/4	0000000	00000000	0000000	000000
7 psi 201 in. of H₂O	81 cfm @ 0	11.1 in. of Hg 151 in. of H₂O	4	10.9 A @ 208 V AC 11.1 A @ 230 V AC 5.5 A @ 460 V AC	73 dB	14"	14"	15"	5° to 100°	1 1/4	1 1/4	0000000	00000000	0000000	000000
7 psi 220 in. of H₂O	168 cfm @ 0	13.3 in. of Hg 180 in. of H₂O	10	26.1 A @ 208 V AC 25.0 A @ 230 V AC 12.5 A @ 460 V AC	77 dB	18"	18"	20"	5° to 100°	2	2	0000000	00000000	0000000	000000
8 psi 231 in. of H₂O	129 cfm @ 0	13.3 in. of Hg 180 in. of H₂O	7 1/2	19.8 A @ 208 V AC 19.5 A @ 230 V AC 9.7 A @ 460 V AC	75 dB	18"	17"	19"	5° to 100°	2	2	0000000	00000000	0000000	000000

High-Flow Low-Pressure Hazardous Location Compressed Air Blowers

Safely produce high-flow compressed air with low pressure or vacuum in environments with flammable gases and combustible dust, such as propane and carbon-based dust. These blowers have an explosion-proof motor and are UL listed for use in hazardous locations. Also known as regenerative blowers, they are commonly used to operate pump drives, lift tables, and conveying systems. They can also be used for drying, exhausting, and aerating.

For technical drawings and 3-D models, click on a part number.

Single Stage

						Overall				Pipe Size
Max. Pressure	Max. Flow Rate	Vacuum Rating	hp	Full Load Current	Vol., dBA	Lg.	Wd.	Ht.	Temp. Range, °F	Inlet	Outlet	Environmental Rating		Each
Three Phase, 208V AC/230V AC/460V AC (Inverter Rated)
NPT Female Inlet and Outlet
2 psi 50 in. of H₂O	556 cfm @ 0 psi	3.7 in. of Hg 50 in. of H₂O	10	24.3 A @ 208 V AC 22.4 A @ 230 V AC 11.2 A @ 460 V AC	81	25"	20"	22"	5° to 100°	4	4	NEC Class I Division 1 Group D; NEC Class II Division 2 Groups F, G	0000000	000000000
2 psi 60 in. of H₂O	471 cfm @ 0 psi	4.4 in. of Hg 60 in. of H₂O	10	24.3 A @ 208 V AC 22.4 A @ 230 V AC 11.2 A @ 460 V AC	81	25"	19"	22"	5° to 100°	4	4	NEC Class I Division 1 Group D; NEC Class II Division 2 Groups F, G	0000000	00000000
2 psi 68 in. of H₂O	381 cfm @ 0 psi	5 in. of Hg 68 in. of H₂O	7 1/2	18.9 A @ 208 V AC 17.8 A @ 230 V AC 8.9 A @ 460 V AC	80	23"	18"	19"	5° to 100°	3	3	NEC Class I Division 1 Group D; NEC Class II Division 2 Groups F, G	0000000	00000000
4 psi 116 in. of H₂O	294 cfm @ 0 psi	8.8 in. of Hg 116 in. of H₂O	7 1/2	18.9 A @ 208 V AC 17.8 A @ 230 V AC 8.9 A @ 460 V AC	80	23"	16"	19"	5° to 100°	3	3	NEC Class I Division 1 Group D; NEC Class II Division 2 Groups F, G	0000000	00000000

Two Stage

						Overall				Pipe Size
Max. Pressure	Max. Flow Rate	Vacuum Rating	hp	Full Load Current	Vol., dBA	Lg.	Wd.	Ht.	Temp. Range, °F	Inlet	Outlet	Environmental Rating		Each
Three Phase, 208V AC/230V AC/460V AC (Inverter Rated)
NPT Female Inlet and Outlet
2 psi 115 in. of H₂O	274 cfm @ 0 psi	8.5 in. of Hg 115 in. of H₂O	10	24.3 A @ 208 V AC 22.4 A @ 230 V AC 11.2 A @ 460 V AC	81	27"	20"	22"	5° to 100°	4	4	NEC Class I Division 1 Group D; NEC Class II Division 2 Groups F, G	0000000	000000000
3 psi 110 in. of H₂O	220 cfm @ 0 psi	8.1 in. of Hg 110 in. of H₂O	7 1/2	18.9 A @ 208 V AC 17.8 A @ 230 V AC 8.9 A @ 460 V AC	78	27"	19"	22"	5° to 100°	4	4	NEC Class I Division 1 Group D; NEC Class II Division 2 Groups F, G	0000000	00000000
5 psi 150 in. of H₂O	167 cfm @ 0 psi	11 in. of Hg 150 in. of H₂O	7 1/2	18.9 A @ 208 V AC 17.8 A @ 230 V AC 8.9 A @ 460 V AC	77	23"	18"	19"	5° to 100°	2	2	NEC Class I Division 1 Group D; NEC Class II Division 2 Groups F, G	0000000	00000000
8 psi 240 in. of H₂O	128 cfm @ 0 psi	11.9 in. of Hg 240 in. of H₂O	7 1/2	18.9 A @ 208 V AC 17.8 A @ 230 V AC 8.9 A @ 460 V AC	75	27"	16"	19"	5° to 100°	2	2	NEC Class I Division 1 Group D; NEC Class II Division 2 Groups F, G	0000000	00000000

Blowers

These blowers install in ductwork similar to duct fans, but are for use where high static pressures are present. Use them for equipment cooling, material conveying, drying, ventilating, and exhausting. All blowers have an open dripproof motor enclosure for relatively clean, dry, indoor locations.

Note: Airflow depends on the resistance created by ductwork. This resistance, known as static pressure (SP), is measured in inches of water.

For technical drawings and 3-D models, click on a part number.

Blowers
				Outlet				Overall									Replacement Wheels
Airflow @ Static Pressure	Volume	Motor Speed, rpm	Power, hp	Ht.	Wd.	Inlet Dia.	Wheel Dia.	Ht.	Wd.	Dp.	Wt., lbs.	Temp. Range, °F	Mount. Fasteners Included	Mount. Hole Dia.		Each		Each
With Rectangular Outlet and Round Inlet—Open Dripproof Motor Enclosure
120V AC, Single Phase—Hardwire
300 cfm @ 3/4 in. of H₂O 515 cfm @ 1/4 in. of H₂O	45 dBA @ 15 ft.	1,750	1/6	7 3/8"	4 1/4"	6"	6 1/4"	15 5/8"	15"	11"	28	-15° to 180°	No	3/8"	0000000	0000000	0000000	000000
120/230V AC, Single Phase—Hardwire
855 cfm @ 3/4 in. of H₂O 1,100 cfm @ 1/4 in. of H₂O	50 dBA @ 15 ft.	1,140	1/3	10 3/4"	6 1/2"	9"	9"	18 5/8"	17 5/8"	14 7/8"	54	-15° to 180°	No	3/8"	0000000	00000000	0000000	000000
865 cfm @ 3/4 in. of H₂O 1,000 cfm @ 1/4 in. of H₂O	50 dBA @ 15 ft.	1,750	1/3	8 1/4"	5 3/8"	8"	7 3/4"	16 1/2"	16 1/4"	13 5/8"	44	-15° to 180°	No	3/8"	0000000	000000	0000000	000000
1,500 cfm @ 3/4 in. of H₂O 1,800 cfm @ 1/4 in. of H₂O	55 dBA @ 15 ft.	1,150	3/4	11 3/4"	8"	10"	10 5/8"	22 1/2"	18 7/8"	17 1/4"	84	-15° to 180°	No	3/8"	0000000	00000000	0000000	000000
230/460V AC, Three Phase—Hardwire
300 cfm @ 3/4 in. of H₂O 515 cfm @ 1/4 in. of H₂O	45 dBA @ 15 ft.	1,750	1/4	7 3/8"	4 1/4"	6"	6 1/4"	15 5/8"	15"	11"	34	-15° to 180°	No	3/8"	0000000	000000	0000000	00000
855 cfm @ 3/4 in. of H₂O 1,100 cfm @ 1/4 in. of H₂O	50 dBA @ 15 ft.	1,150	1/3	10 3/4"	6 1/2"	9"	9"	18 5/8"	17 5/8"	14 7/8"	49	-15° to 180°	No	3/8"	0000000	00000000	0000000	000000
865 cfm @ 3/4 in. of H₂O 1,000 cfm @ 1/4 in. of H₂O	50 dBA @ 15 ft.	1,750	1/3	8 1/4"	5 3/8"	8"	7 3/4"	16 1/2"	16 1/4"	13 5/8"	37	-15° to 180°	No	3/8"	0000000	00000000	0000000	000000
1,500 cfm @ 3/4 in. of H₂O 1,800 cfm @ 1/4 in. of H₂O	55 dBA @ 15 ft.	1,150	3/4	11 3/4"	8"	10"	10 5/8"	22 1/2"	18 7/8"	17 1/4"	67	-15° to 180°	No	3/8"	0000000	00000000	0000000	000000

Hazardous Location Spark-Resistant Blowers

These blowers have an explosion-proof motor that is UL listed for hazardous locations. They also have an aluminum housing for spark resistance. These blowers install in ductwork similar to duct fans, but are for use where high static pressures are present. Use them for equipment cooling, material conveying, drying, ventilating, and exhausting.

Note: Airflow depends on the resistance created by ductwork. This resistance, known as static pressure (SP), is measured in inches of water.

For technical drawings and 3-D models, click on a part number.

							Overall
Airflow @ Static Pressure	Volume	Motor Speed, rpm	Power, hp	Outlet Dia.	Inlet Dia.	Wheel Dia.	Ht.	Wd.	Dp.	Temp. Range, °F	Mount. Fasteners Included	Mount. Hole Dia.		Each
With Round Outlet and Inlet
120/230V AC, Single Phase—Hardwire
295 cfm @ 1 in. of H₂O 505 cfm @ 1/4 in. of H₂O	55 dBA @ 15 ft.	1,750	1/3	6"	6"	6 1/4"	14 1/8"	12 1/4"	13 1/4"	0° to 150°	No	7/16"	0000000	000000000
320 cfm @ 1 in. of H₂O 375 cfm @ 1/4 in. of H₂O	60 dBA @ 15 ft.	3,450	1/3	4"	5"	4 3/4"	12 5/8"	9 7/8"	12 1/4"	0° to 150°	No	7/16"	0000000	00000000
995 cfm @ 1 in. of H₂O 1,070 cfm @ 1/4 in. of H₂O	70 dBA @ 15 ft.	3,450	1 1/2	6"	6"	6 1/4"	14 1/8"	12 1/4"	13 1/4"	0° to 150°	No	7/16"	0000000	00000000
1,045 cfm @ 1/4 in. of H₂O	55 dBA @ 15 ft.	1,150	1/3	8"	8"	8 1/4"	18 3/4"	14 3/4"	15 3/8"	0° to 150°	No	7/16"	0000000	00000000

Spark-Resistant Blowers

These blowers have an aluminum housing for spark resistance. Use them for equipment cooling, material conveying, drying, ventilating, and exhausting. All blowers have a totally enclosed motor enclosure, which can be used in dirty, dusty, and damp environments.

Note: Airflow depends on the resistance created by ductwork. This resistance, known as static pressure (SP), is measured in inches of water.

For technical drawings and 3-D models, click on a part number.

							Overall
Airflow @ Static Pressure	Volume	Motor Speed, rpm	Power, hp	Outlet Dia.	Inlet Dia.	Wheel Dia.	Ht.	Wd.	Dp.	Temp. Range, °F	Mount. Fasteners Included	Mount. Hole Dia.		Each
With Round Outlet and Inlet—Totally Enclosed Motor Enclosure
120/230V AC, Single Phase—Hardwire
1,045 cfm @ 1/4 in. of H₂O	55 dBA @ 15 ft.	1,150	1/3	8"	8"	8 1/4"	18 3/4"	14 3/4"	15 3/8"	0° to 150°	No	7/16"	0000000	000000000
1,070 cfm @ 1/4 in. of H₂O 995 cfm @ 1 in. of H₂O	70 dBA @ 15 ft.	3,450	1 1/2	6"	6"	6 1/4"	14 1/8"	12 1/4"	13 1/4"	0° to 150°	No	7/16"	0000000	00000000
295 cfm @ 1 in. of H₂O 505 cfm @ 1/4 in. of H₂O	55 dBA @ 15 ft.	1,750	1/4	6"	6"	6 1/4"	14 1/8"	12 1/4"	13 1/4"	0° to 150°	No	7/16"	0000000	000000
320 cfm @ 1 in. of H₂O 375 cfm @ 1/4 in. of H₂O	60 dBA @ 15 ft.	3,450	1/3	4"	5"	4 3/4"	12 5/8"	9 7/8"	12 1/4"	0° to 150°	No	7/16"	0000000	000000

Portable Blowers

Powerful enough for use with flexible duct, yet light enough to carry from job to job. Use these blowers for equipment cooling, material conveying, drying, ventilating, and exhausting. Blowers have a totally enclosed motor enclosure, which can be used in dirty, dusty, and damp environments.

For technical drawings and 3-D models, click on a part number.

					Overall
Airflow, cfm	Volume	Motor Speed, rpm	Power, hp	For Duct Dia.	Ht.	Wd.	Dp.	Plug Type	Cord Lg., ft.	Temp. Range, °F	Housing Material	Blade Material		Each
120V AC, Single Phase—Plug
775	70 dBA @ 15 ft.	3,200	1/3	8"	10"	8"	12"	Three Prong	6	-10° to 150°	Powder-Coated Steel	Polypropylene Plastic	000000	0000000
1,700	80 dBA @ 15 ft.	3,200	1/3	12"	15"	12"	15 1/2"	Three Prong	20	-10° to 150°	Powder-Coated Steel	Polypropylene Plastic	000000	000000

Air-Powered Portable Blowers

Use your compressed air source to power these blowers. They are powerful enough for use with flexible duct, yet light enough to carry from job to job. Use them for equipment cooling, material conveying, drying, ventilating, and exhausting.

Note: Airflow is based on an air supply of 80 psi.

For technical drawings and 3-D models, click on a part number.

Blowers														Duct
Airflow, cfm	Airflow @ Duct Lg.	Volume	Air Consumption, cfm	Max. Air Pressure, psi	Air Inlet Pipe Size	For Duct Dia.	O'all Dp.	Base Dia.	Temp. Range, °F	Housing Material	Mount. Fasteners Included		Each		Each
NPT Female Air Inlet
With Galvanized Steel Diffuser
1,000	600 cfm @ 50 ft.	70 dBA @ 5 ft.	50	150	1/2	6"	16 3/4"	7 5/16"	-15° to 350°	Aluminum	No	0000000	0000000	0000000	0000000
7,300	4,000 cfm @ 50 ft.	80 dBA @ 5 ft.	380	150	1	16"	48"	17"	-15° to 350°	Aluminum	No	0000000	00000000	0000000	000000
With Powder-Coated Steel Diffuser
1,500	Not Rated	80 dBA @ 15 ft.	60	150	1/2	6"	16 1/2"	7 1/2"	-15° to 350°	Aluminum	No	0000000	000000	0000000	000000
1,700	1,350 cfm @ 50 ft.	80 dBA @ 15 ft.	60	150	1/2	8"	33"	7 1/2"	-15° to 350°	Aluminum	No	0000000	000000	0000000	000000
4,500	3,580 cfm @ 50 ft.	85 dBA @ 15 ft.	125	150	1	12"	44 1/4"	11 1/2"	-15° to 350°	Aluminum	No	0000000	00000000	0000000	000000
With Plastic Diffuser
1,500	Not Rated	80 dBA @ 15 ft.	60	150	1/2	6"	16 1/2"	7 1/2"	-15° to 160°	Aluminum	No	0000000	000000	0000000	000000
1,700	1,350 cfm @ 50 ft.	80 dBA @ 15 ft.	60	150	1/2	8"	33"	7 1/2"	-15° to 160°	Aluminum	No	0000000	000000	0000000	000000
4,500	3,580 cfm @ 50 ft.	85 dBA @ 15 ft.	125	150	1	12"	44 1/4"	11 1/2"	-15° to 160°	Aluminum	No	0000000	00000000	0000000	000000

High-Output Portable Blowers

Blow twice as much air as other portable blowers. These are powerful enough for use with flexible duct, yet light enough to carry from job to job. Use them for equipment cooling, material conveying, drying, ventilating, and exhausting. All blowers have a totally enclosed motor enclosure, which can be used in dirty, dusty, and damp environments. They rest on the floor with their built-in base or can be mounted on an optional stand (sold separately).

						Overall
Airflow, cfm	Airflow @ Duct Lg.	Volume	Motor Speed, rpm	Power, hp	For Duct Dia.	Ht.	Wd.	Dp.	Plug Type	Temp. Range, °F	Housing Material	Blade Material		Each
120V AC, Single Phase—Plug
1,500	1,000 cfm @ 50 ft.	80 dBA @ 15 ft.	3,450	3/4	8"	13 3/4"	11 3/8"	39"	Three Prong	-15° to 125°	Aluminum	ABS Plastic	0000000	000000000
3,000	2,300 cfm @ 50 ft.	85 dBA @ 15 ft.	3,450	1	12"	15 5/8"	13 1/4"	36"	Three Prong	-15° to 125°	Aluminum	Aluminum	0000000	00000000
230V AC, Single Phase—Hardwire, Plug
3,000	2,300 cfm @ 50 ft.	85 dBA @ 15 ft.	3,450	1	12"	15 5/8"	13 1/4"	36"	__	-15° to 125°	Aluminum	Aluminum	0000000	00000000

Optional 26" Stand

0000000

Each

000000000

Hazardous Location High-Output Portable Blowers

In addition to blowing twice as much air as other portable blowers, these have an explosion-proof motor that is UL listed for Class I, Divisions 1 and 2, Group D; and Class II, Divisions 1 and 2, Groups E, F, and G hazardous locations. They are powerful enough for use with flexible duct, yet light enough to carry from job to job. Use them for equipment cooling, material conveying, drying, ventilating, and exhausting. They rest on the floor with their built-in base or can be mounted on an optional stand (sold separately).

						Overall
Airflow, cfm	Airflow @ Duct Lg.	Volume	Motor Speed, rpm	Power, hp	For Duct Dia.	Wd.	Dp.	Temp. Range, °F	Housing Material	Blade Material	Environmental Rating		Each
120V AC, Single Phase—Hardwire
1,500	1,000 cfm @ 50 ft.	80 dBA @ 15 ft.	3,450	3/4	8"	11 3/8"	39"	-15° to 125°	Aluminum	ABS Plastic	NEC Class I Divisions 1, 2 Group D NEC Class II Divisions 1, 2 Groups E, F, G NEMA 7 NEMA 9	0000000	000000000
3,000	2,300 cfm @ 50 ft.	85 dBA @ 15 ft.	3,450	1	12"	13 1/4"	36"	-15° to 125°	Aluminum	Aluminum	NEC Class I Divisions 1, 2 Group D NEC Class II Divisions 1, 2 Groups E, F, G NEMA 7 NEMA 9	0000000	00000000
230V AC, Single Phase—Hardwire
3,000	2,300 cfm @ 50 ft.	85 dBA @ 15 ft.	3,450	1	12"	13 1/4"	36"	-15° to 125°	Aluminum	Aluminum	NEC Class I Divisions 1, 2 Group D NEC Class II Divisions 1, 2 Groups E, F, G NEMA 7 NEMA 9	0000000	00000000

Optional 26" Stand

0000000

Each

000000000

Corrosion-Resistant Portable Blowers

A plastic housing offers good corrosion resistance. These blowers are powerful enough for use with flexible duct, yet light enough to carry from job to job. Use them for equipment cooling, material conveying, drying, ventilating, and exhausting. Blowers have a totally enclosed motor enclosure, which can be used in dirty, dusty, and damp environments. They are stackable for increased airflow and storage.

						Overall
Airflow, cfm	Airflow @ Duct Lg.	Volume	Motor Speed, rpm	Power, hp	For Duct Dia.	Ht.	Wd.	Dp.	Plug Type	Cord Lg., ft.	Temp. Range, °F	Housing Material	Blade Material		Each
120V AC, Single Phase—Plug
875	480 cfm @ 50 ft.	70 dB @ 15 ft.	3,200	1/4	8"	18 1/2"	12 1/2"	18 1/2"	Three Prong	20	-20° to 150°	Polyethylene Plastic	Polypropylene Plastic	00000000	0000000
2,000	1,600 cfm @ 50 ft.	80 dB @ 15 ft.	3,425	1	12"	21"	14"	17"	Three Prong	20	-20° to 150°	Polyethylene Plastic	Polypropylene Plastic	00000000	000000