A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A clear polyurethane bowl makes these filter/regulators chemical resistant for use with synthetic compressor oils and cleaning fluids and allows you to see inside to monitor contents.

With ±0.2 psi accuracy, these filter/regulators provide more precise control than our other compressed air filter/regulators.

Assembled, inspected, and packaged in a clean environment, these filter/regulators come sealed in antistatic double bags.

An SMC filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Wilkerson filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

An ARO filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Festo filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

No need for thread adapters—these filter/regulator/lubricators have an NPT inlet and a BSPP outlet.

Distribute compressed air to multiple locations from a single source.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air. Joiner clamps connect these air filters into your Parker setup.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Use these filters where high water and dirt removal is needed—they have a two-layer filter element made of stainless steel wire mesh and cotton/polyester packing.

A polyurethane bowl provides good chemical resistance for use with synthetic compressor oils and cleaning fluids.

Get two stages of filtration—the first stage removes most particles and water droplets; the second captures any remaining particles and water droplets down to 5 microns.

Discharge up to 300 gallons of water and particles per hour—these filters handle compressed air that’s high in moisture content.

Remove particles from large volumes of compressed air without causing restriction or drops in pressure.

Replace the filter element in your SMC modular compressed air filter to trap solid particles and water droplets as small as 5 microns.

Replace the filter element in your Parker modular compressed air filter to trap solid particles and water droplets.

Replace the filter element in your Festo modular compressed air filter to trap solid particles and water droplets.

Replace the filter element in your Aventics modular compressed air filter to trap solid particles and water droplets.

Also known as coalescing filters, these filter elements fit in Aventics modular compressed air filters to remove oil and particles as small as 0.01 microns.

Also known as coalescing filters, these filter elements fit in Festo modular compressed air filters to remove oil and particles as small as 0.01 microns.

Also known as coalescing filters, these filter elements fit in ARO modular compressed air filters to remove oil and particles as small as 0.3 microns.

Replace a damaged bowl, or change the bowl material or drain type on your SMC modular compressed air filter.

Replace a damaged bowl or change the bowl material or drain type on your Parker modular compressed air filter.

Replace a damaged bowl or change the bowl material or drain type on your ARO modular compressed air filter.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Use these filters to extend the service life of air-powered tools and equipment and then throw them away when you're done.

Mount these filters to a 35 mm DIN rail with the included brackets.

Housing and bowl are 316 stainless steel to handle extremely corrosive environments and meet NACE (National Association of Corrosion Engineers) specifications.

Eliminate small traces of oil vapor and its associated odor with these filters and then throw them away when you're done.

Two-stage filtration is like getting two filters in one—the first stage removes large particles, while the second removes fine particles.

Produce clean air for instrumentation and other applications, such as food or medical device manufacturing.

Often used in medical device manufacturing and food-processing facilities, these filters have a stainless steel element that can be sterilized in an autoclave.

With a clear polycarbonate bowl that’s visible from all angles and silica gel desiccant that changes from blue to pink, it’s easy to see when it’s time to change the cartridge on these dryer/filters and dryer/filter/regulators.

These dryer/filters have a clay desiccant that removes moisture, oil, and particles, so there’s no need to install a separate filter and dryer. Once aftercoolers and separators have removed the bulk of the water, they remove any remaining moisture in your air line.

Once aftercoolers and separators have removed the bulk of the water, use these dryers to remove any remaining moisture in your air line.

For use with Norgren modular compressed air systems, once aftercoolers and separators have removed the bulk of the water, use one of these desiccant-filled dryers to remove any remaining moisture in your air line.

These all-in-one dryers with filters eliminate the need for individual dryers and filters. They cool air through refrigeration to condense water vapor for removal.

Prevent equipment damage caused by moisture. The first step in water removal, these separators remove the water that accumulates as compressed air cools.

In addition to removing large amounts of water, these separators also remove particles and oil droplets. Place them after your compressor and aftercooler, or at the point of use in applications that don't require an aftercooler.

Let these separators handle the dirty work of condensate disposal. These separators use two-stage filtration to cut oil content to under five parts per million.