Adjust and maintain the pressure of your compressed air.

Adjust and maintain the pressure of your compressed air.

Adjust and maintain the pressure of your compressed air.

Adjust and maintain the pressure of your compressed air.

Cleaned and double bagged in an ISO Class 3 and Fed. Spec. Class 1 clean room for protection from contamination, these regulators are suitable for use in clean rooms.

Use these regulators to adjust and maintain the pressure of your tubing air lines.

Prevent unauthorized adjustment and unintentional pressure changes with these regulators.

A lower profile than our other compressed air regulators makes these regulators a better fit in tight spots.

Fit these regulators in tight spaces to adjust and maintain air pressure in sensitive applications where constant, consistent pressure is important.

At ±0.1% accuracy, use these regulators in sensitive applications where constant, consistent pressure is important.

With a greater flow capacity than our standard precision compressed air regulators, use these regulators to adjust and maintain air pressure in sensitive high-flow applications where constant, consistent pressure is important.

Designed for control applications that require high reliability and repeatability, these regulators translate electrical signals to output pressure.

Mount these regulators to a 35 mm DIN rail with the included bracket.

Connect two or more of these manifold regulators to meet multiple pressure requirements from a single air supply—set a different output pressure with each regulator.

Run up to four air-powered tools from a single air supply.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

Assembled, inspected, and packaged in a clean environment, these filter/regulators come sealed in antistatic double bags.

A clear polyurethane bowl makes these filter/regulators chemical resistant for use with synthetic compressor oils and cleaning fluids and allows you to see inside to monitor contents.

A stainless steel housing and bowl allow these filter/regulators to withstand corrosive environments in the semiconductor, marine, chemical, instrumentation, and paper industries.

An SMC filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Wilkerson filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Parker filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

An ASCO Numatics filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A filter, regulator, and lubricator with push-to-connect fittings are combined to provide clean, lubricated compressed air at your required pressure. Fittings make a tight seal around tubing.

Prevent accidental start-up when servicing equipment.

Prevent accidental start-up when servicing equipment.

Also known as Monday-morning valves, these valves slowly introduce pressure to reduce surge damage during start-up.

Replace the filter element in your SMC modular compressed air filter to trap solid particles and water droplets as small as 5 microns.

Designed to be mounted inline, these valves can be installed in an easy-to-reach location along your line. They control the speed of air-powered equipment by adjusting the volume of airflow.

A numeric indicator provides a relative measure of airflow, similar to the volume dial on a speaker, so it's easy to set the same flow rate with each use. Mount them directly to cylinder ports, eliminating additional tubing between the cylinder and valve for better control than inline valves. They control the speed of air-powered equipment by adjusting the volume of airflow.

A fine-adjustment dial allows tighter control of airflow and cylinder speed than other flow control valves. They control the speed of air-powered equipment by adjusting the volume of airflow entering or exiting.

Designed to be mounted inline, these valves can be placed in easy-to-reach locations. Made of plastic and stainless steel parts, they have excellent corrosion resistance. They control the speed of air-powered equipment by adjusting the volume of airflow.

These valves handle pressure up to 265 psi. They control the speed of air-powered equipment by adjusting the volume of airflow entering or exiting.

Adjust airflow equally in both directions. These valves regulate the speed of airflow as it enters and exits equipment. They're often used to control the extension and retraction speed of an air cylinder at the same time.

Prevent damage to your equipment by limiting startup airflow and then gradually raising the airflow rate to operating levels.

Designed for high-pressure instrumentation applications, these valves are rated for up to 10,000 psi and have a hex nut and threads below the handle for panel mounting. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

The color-coded threads and numerical markings on these valves ensure consistent and repeatable settings. One full revolution of the handle reveals a new color to indicate the set point. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With a gauge port on each side of these valves, you can install two different pieces of instrumentation equipment to simultaneously monitor multiple media properties without interrupting flow. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Also known as block and bleed valves, these have a vent port that allows you to remove instrumentation equipment attached to the valve without depressurizing your line. Turn the handle to shut off flow and remove the vent port plug to drain liquid trapped in the valve. Use them with water, oil, air, and inert gas. These valves adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For installation in instrument panels, these valves have a hex nut and threads below the handle. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Solder these valves to tubing for a permanent, leak-tight connection. Use them with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Barbs grip onto tubing, providing a secure hold. These valves are for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Barbs grip onto tubing, providing a secure hold. To withstand aggressive and corrosive solutions in chemical-processing applications, these valves have a PTFE seal and a PVDF body. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. The 316 stainless steel body and seal, the PTFE seat and packing, and the Monel needle can withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

These valves are for use with water, oil, air, and inert gas. They bolt to flanges to adjust and regulate flow in flanged pipelines.

For a longer service life than other flanged flow-adjustment valves, these are designed to open and close with minimal wear on internal components. Use with water, air, and inert gas. They bolt to flanges to adjust and regulate flow in flanged pipelines.

Also known as whistle valves, these open and throttle as force is applied to the lever and automatically close upon release. They’re commonly used for spraying, washing, and other applications that require manual discharge of liquid and air. Use with water, oil, air, and inert gas.

Available in smaller pipe sizes than other solenoid flow-adjustment valves, these are often used with gas chromatography equipment and analytical instrumentation. They adjust and regulate flow based on the intensity of the electrical signal into the valve. They're often integrated into PLC systems for automatic control over the valve position based on system conditions.

A cast iron body absorbs vibration from pressure changes to reduce wear and noise in your pipeline.

Thicker walls and a 304 stainless steel seal make these valves tougher than brass pressure-regulating valves.

These valves automatically reduce a high, variable inlet pressure to a lower, stable outlet pressure.

To maintain contaminant-free standards in clean room environments, these valves come cleaned and bagged to Fed. Std. Class 100 and ISO Class 5 clean room standards and have a 316 stainless steel body with a smooth finish to resist dust collection.

Withstand more than six times the inlet pressure of standard pressure-regulating valves.

For extremely high-pressure applications in tight spots, these valves handle the same inlet pressures as other ultra-high-pressure-regulating valves within a smaller footprint.

Commonly used for oxygen service and other high-purity applications, these valves come cleaned and bagged to prevent contamination.

Withstand inlet pressures up to 3,500 psi.

A 316 stainless steel body provides exceptional corrosion resistance in wet conditions and harsh environments.

Threads below the adjustment knob and an included panel-mount nut allow you to add these valves to your instrument panel.

These valves have a brass body.

A lighter and more corrosion-resistant alternative to metal vacuum-regulating valves.