Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Use these filters where high water and dirt removal is needed—they have a two-layer filter element made of stainless steel wire mesh and cotton/polyester packing.

Get two stages of filtration—the first stage removes most particles and water droplets; the second captures any remaining particles and water droplets down to 5 microns.

The housing and bowl are 316 stainless steel to handle extremely corrosive environments such as those in semiconductor, marine, chemical, and paper industries.

Protect small air-powered tools, such as impact wrenches, ratchet wrenches, grinders, and screwdrivers.

Assembled, inspected, and packaged in a clean environment, these filters come sealed in antistatic double bags.

Two-stage filtration is like getting two filters in one—the first stage removes large particles, while the second removes fine particles.

Generate clean air for instrumentation and applications with critical air requirements.

Remove bacteria, viruses, moisture, and other particles from compressed air and gases used in food, pharmaceutical, biotech, and electronics applications.

These separators have higher flow rates compared to our other compressed air separators. Prevent equipment damage and wear caused by moisture in your compressed air supply. The first step in water removal, use one of these separators to remove the large amount of water created as compressed air cools.

When water is condensed out of a compressed air system, it contains oil from the compressor that makes disposal difficult. These separators use two-stage filtration to reduce oil content to below 20 parts per million.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

These filter/regulator combinations come as one convenient unit that cleans the air as it regulates pressure.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A clear polyurethane bowl makes these filter/regulators chemical resistant for use with synthetic compressor oils and cleaning fluids and allows you to see inside to monitor contents.

With ±0.2 psi accuracy, these filter/regulators provide more precise control than our other compressed air filter/regulators.

Mount these filter/regulators to a 35 mm DIN rail with the included brackets.

A filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Parker filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

An ASCO Numatics filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

No need for thread adapters—these filter/regulator/lubricators have an NPT inlet and a BSPP outlet.

A filter, regulator, and lubricator with push-to-connect fittings are combined to provide clean, lubricated compressed air at your required pressure. Fittings make a tight seal around tubing.

Get dry compressed air in high-pressure systems—these dryers have a maximum pressure rating of 300 psi. Once aftercoolers and separators have removed the bulk of the water, they remove any remaining moisture in your air line.

With a clear polycarbonate bowl that’s visible from all angles and silica gel desiccant that changes from blue to pink, it’s easy to see when it’s time to change the cartridge on these dryer/filters and dryer/filter/regulators.

These dryer/filters have a clay desiccant that removes moisture, oil, and particles, so there’s no need to install a separate filter and dryer. Once aftercoolers and separators have removed the bulk of the water, they remove any remaining moisture in your air line.

Install these dryers just before air-powered tools as final protection from water and particles and throw them away when you’re done.

These all-in-one dryers with filters eliminate the need for individual dryers and filters. They cool air through refrigeration to condense water vapor for removal.