The face and head are made of aluminum-bronze that is Factory Mutual approved, so these tools inhibit sparking, resist corrosion, and are nonmagnetic. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Use the domed end of the head for forming soft metal, rounding off edges, and closing rivets. The flat striking face is for driving nails, pins, punches, and chisels. All have a textured grip for slip resistance. For replacement handles, see Fiberglass Hammer Handles.

Warning: Do not use these tools in direct contact with acetylene.

The replaceable faces can be changed out when worn. These mallets have a head loaded with metal shot for added weight and a controlled impact with minimal rebound. Use them to drive chisels and strike work without damaging its surface. The polyurethane rubber faces resist oils and solvents and won't crack under high impact; they're often used on plastic, wood, and sheet metal. To avoid marring when tapping or striking, choose a face that's softer than your workpiece. Lighter weight mallets are good for tapping work into place and driving a chisel to make small cuts. Use heavier weight mallets when assembling joints, dislodging stuck parts, and making aggressive cuts with a chisel. Longer mallets allow for more powerful swings. The handle has a ribbed grip for slip resistance.

The faces and head are made of aluminum-bronze that is Factory Mutual approved, so these tools inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Use them to demolish material, form metal, and drive punches, chisels, and masonry drills. For demolition work, ensure that the workpiece is softer than the metal faces. Longer and heavier hammers deliver greater impact. All have a textured or ribbed grip for slip resistance. For replacement handles, see Fiberglass Hammer Handles.

Warning: Do not use these tools in direct contact with acetylene.

The faces and head are made of aluminum-bronze that is Factory Mutual approved, so these tools inhibit sparking, resist corrosion, and are nonmagnetic. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. All are suitable for driving chisels and striking work without damaging its surface. To avoid marring the workpiece, use these mallets on material that is harder than the metal faces. Lighter weight mallets are good for tapping work into place and driving a chisel to make small cuts. Use heavier weight mallets when assembling joints, dislodging stuck parts, and making aggressive cuts with a chisel. A textured grip provides slip resistance. For replacement handles, see Fiberglass Hammer Handles.

Warning: Do not use these tools in direct contact with acetylene.

The face and head are made of aluminum-bronze that is Factory Mutual approved, so these tools inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Use them to drive and remove nails. All have a textured grip for slip resistance. For replacement handles, see Fiberglass Hammer Handles.

Warning: Do not use these tools in direct contact with acetylene.

Replace faces when they become worn rather than replacing the entire tool. These mallets are suitable for driving chisels and striking work without damaging its surface. Choose a mallet with a face that's softer than your workpiece to avoid marring it when tapping or striking. Lighter weight mallets are good for tapping work into place and driving a chisel to make small cuts. Use heavier weight mallets when assembling joints, dislodging stuck parts, and making aggressive cuts with a chisel. Longer mallets allow for more powerful swings.

The faces and head are made of aluminum-bronze that is Factory Mutual approved, so these tools inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Use the flat end of the head to strike metal, concrete, and stone; the wedge-shaped end is for shaping and bending metal. These tools are also known as cross-peen hammers. A textured grip provides slip resistance. For replacement handles, see Fiberglass Hammer Handles.

Warning: Do not use these tools in direct contact with acetylene.

Also known as zip guns, these air hammers require a rivet setter and a bucking bar (each sold separately) to install solid rivets. Choose a rivet setter that matches the rivet's head style. As the tool strikes the rivet head, the back side of the rivet is hammered against the bucking bar, deforming the body and fastening your material. They can also be used as a chiseling air hammer when paired with chiseling bits. Stroke length determines the hammering power. The longer the stroke, the greater the power.