These 18-8 stainless steel anchors have good chemical resistance.

Keep fixtures solidly in place—these anchors have two locking wedges that won't shake loose.

These 18-8 stainless steel anchors have good chemical resistance.

An open-end cap nut provides a finished appearance.

These 18-8 stainless steel anchors have good chemical resistance.

Drive these tools with a hammer until the thicker portion of the tool makes contact with the anchor, causing it to expand.

These 316 stainless steel anchors have excellent resistance to chemicals and salt water.

Also known as caulk-in anchors, these stay secure when there's not much material to hold.

An adjustable stop allows you to set anchors at consistent depths. Use with a hammer.

Often referred to as four-way expansion anchors, these expand in four directions to resist loosening from vibration.

Also known as mungo anchors, these have large fins that prevent rotation.

Also known as lag shields, these anchors are designed for use with large-diameter wood screws.

These anchors are also known as drive rivets. To install, hammer the pin into the body. Pry out the pin to remove.

These anchors are also known as drive rivets. To install, hammer the screw into the body. Unthread the screw to remove.

A tamper-resistant nut prevents unwanted removal of the object you are anchoring.

These 316 stainless steel anchors have excellent resistance to chemicals and salt water.

A hex head allows for a secure grip with a wrench.

A pivoting toggle bar creates a strong hold.

Used with adhesive in bricks and hollow blocks, such as cinder blocks, these mesh tubes create a stronger hold for rods and studs than other anchors.

18-8 stainless steel anchors have good chemical resistance.

These steel anchors are available with corrosion-resistant finishes.

Easy to install, tap these anchors in like a nail—no drilled hole required.

A drilled hole is required for installation.

A spring-loaded toggle holds against the back of the material.

Bolts are beveled under the head for use in countersunk holes.

A shallow head makes these bolts good for low-clearance applications.

These blue and silver ultra-corrosion-resistant coated steel screws stand up to wet environments.

These 410 stainless steel screws are more corrosion resistant than ultra-corrosion-resistant coated steel screws.

Attach the components of these sets onto a hammer drill to install tapping screws in concrete, block, and brick.

The spring holds the washer and toggle against opposite sides of the wall, so everything's in position before you begin tightening. Once tightened, the spring adds vibration resistance.

You can use these versatile hangers in a threaded hole (as you would a screw), or secure them with a nut (as you would a bolt).

These hangers have internal threads for use with threaded rods, bolts, and anchors.

About half the strength of medium-strength bolts, these bolts are for light duty work-holding.

Use these light duty anchors to hold 20 lbs. or less.

These metric 316 stainless steel studs have excellent resistance to chemicals and salt water. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.

Also known as dowel screws, use these to join two pieces of wood.

You need access to only one side of the material to install these rivets.

Join two beams in a straight line.

Attach these clamps to the flange of an beam, then hang a threaded rod from the threaded hole.

Also known as purlin clamps, these clamps are shaped to fit around beams that have a 45° or 90° lip.

Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.

A secure way to hang threaded rod from a pair of angles, such as those used in ceiling joists, without the need to drill or weld. These clamps are commonly used to suspend HVAC, conveyor, and other overhead systems.

Attach these light duty hangers to beams and other structural elements. They include a stiff wire for supporting ceilings, lighting fixtures, and other lightweight material.

For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

Hold pipe, tubing, and conduit away from strut channel.

For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Flexible grooves inside these polypropylene clamps allow material to expand and contract. Clamps are moisture and chemical resistant.

Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.

Slide these clamps into strut channel and snap closed for quick installation with no tools required. They are noncorrosive, nonconductive nylon.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.

Support vertical pipes passing through floors.

Fasten these brackets to ceilings, walls, beams, and joists to hang threaded rod.

A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.

Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.

These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.

For a strong, secure connection, mount these hangers by welding them to a rod.

Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.