5/8"-11 Anchors | McMaster-Carr

Filter by

System of Measurement

Diameter

Length

Thread Size

Anchor Type

Material

For Use In

Thread Type

Permanence

Drill Bit Size

Screw Size

Thread Direction

Thread Spacing

Pull-Out Strength

Minimum Installation Depth

Conditions Tested In

Drill Bit Decimal Size Equivalent

Shear Strength

Finish

DFARS Compliance

Nut Width

Washer OD

Installation Torque

Forward

How can we improve?

350 Products

Anchors for Concrete, Block, and Brick

Steel Stud Anchors for Concrete

These steel anchors are available with corrosion-resistant finishes.

18-8 Stainless Steel Stud Anchors for Concrete

These 18-8 stainless steel anchors have good chemical resistance.

Super-Corrosion-Resistant 316 Stainless
Steel Stud Anchors for Concrete

More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.

Vibration-Resistant Stud Anchors for Concrete

Keep fixtures solidly in place—these anchors have two locking wedges that won't shake loose.

Steel Stud Anchors with Hex Nut for Block and Brick

A zinc plating provides corrosion resistance in wet environments.

Stainless Steel Stud Anchors
with Hex Nut for Block and Brick

These 18-8 stainless steel anchors have good chemical resistance.

Steel Female-Threaded Anchors for Concrete

A zinc plating provides corrosion resistance in wet environments.

18-8 Stainless Steel Female-Threaded
Anchors for Concrete

These 18-8 stainless steel anchors have good chemical resistance.

Super-Corrosion-Resistant 316 Stainless
Steel Female-Threaded Anchors for Concrete

More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.

Installation Tools for Female-Threaded Anchors

Drive these tools with a hammer until the thicker portion of the tool makes contact with the anchor, causing it to expand.

Steel Adhesive-Grip Female-Threaded
Anchors for Concrete

A zinc plating provides corrosion resistance in wet environments.

Stainless Steel Adhesive-Grip
Female-Threaded Anchors for Concrete

These 316 stainless steel anchors have excellent resistance to chemicals and salt water.

Shallow-Hole Female-Threaded
Anchors for Block and Brick

Also known as caulk-in anchors, these stay secure when there's not much material to hold.

Vibration-Resistant Female-Threaded
Anchors for Block and Brick

Often referred to as four-way expansion anchors, these expand in four directions to resist loosening from vibration.

Female-Threaded Anchors for Block and Brick

Also known as double expansion anchors, these expand from both sides for full contact and a secure hold.

Heavy Duty Pin-Drive Anchors for Block and Brick

Use in applications requiring high strength.

Female-Threaded Expansion Anchors for Hollow Block and Brick

Female-Threaded Expansion
Anchors for Hollow Block and Brick

For narrow holes and small cavities where toggle anchors won't fit.

Anchors for Wet Concrete

Steel L-Hook Anchors for Wet Concrete

These steel anchors are available with corrosion-resistant finishes.

Stainless Steel L-Hook Anchors for Wet Concrete

18-8 stainless steel anchors have good chemical resistance.

Steel J-Hook Anchors for Wet Concrete

These steel anchors are available with corrosion-resistant finishes.

Stainless Steel J-Hook Anchors for Wet Concrete

18-8 stainless steel anchors have good chemical resistance.

Medium-Strength Steel Hold-Down Bolts

Made from steel comparable to Grade 5 steel, these bolts are suitable for most work-holding applications.

Routing and Suspending

Beam Clamps for Threaded Rod

Attach these clamps to the flange of an beam, then hang a threaded rod from the threaded hole.

Center-Mount Beam Clamps for Threaded Rod

For centered load distribution, these clamps grip both sides of the beam and hang threaded rod from the middle.

Angle Iron Clamps for Threaded Rod

A secure way to hang threaded rod from a pair of angles, such as those used in ceiling joists, without the need to drill or weld. These clamps are commonly used to suspend HVAC, conveyor, and other overhead systems.

Threaded Rod Mounts

Fasten these brackets to ceilings, walls, beams, and joists to hang threaded rod.

Threaded Rod Eye Nuts

Add an eye nut to threaded rod to hang the rod from rings, hooks, and hangers.

Washdown Vibration-Damping
Threaded-Rod-Mount Clamping Hangers

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

Pivoting Threaded-Rod-Mount Loop Hangers

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Swivel Threaded-Rod-Mount Loop Hangers

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Threaded-Rod-Mount Roller Loop Hangers

A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.

Side-Load Threaded-Rod-Mount Loop Hangers

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Suspension Beams for Threaded Rod

Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.

U-Bolts

Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.

U-Bolt Mounting Plates

Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.

U-Bolts with Mounting Plates

A mounting plate provides a more secure hold at the mounting surface.

Vibration-Damping U-Bolts

Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.

Rubber-Cushioned U-Bolts

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to disassemble it.

Roller Supports

Support lines that expand and contract. The roller on these supports compensates for movement in your line from changing temperatures.

Rope and Chain Connectors

Hoist Rings—For Lifting

Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back to compensate for roll and sway when lifting heavy or unbalanced loads.