We will reply to your message within an hour.
Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. Their angled profile allows chamfer, bevel, and other angled cuts.
Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. Their angled profile allows chamfer, bevel, and other angled cuts.
Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. The teeth are angled on both sides so you can make top and bottom chamfer cuts without having to flip the workpiece.
These carbide-tipped end mills provide a sharper, harder cutting edge and better wear resistance than high-speed steel without the brittleness of solid carbide. Their teeth are angled on both sides so you can make top and bottom chamfer cuts without having to flip the workpiece.
Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. The teeth are angled on both sides so you can make top and bottom chamfer cuts without having to flip the workpiece.
Mill an angled edge to the entire outside diameter of pipe, tubes, and rods in a single pass with more speed and precision than a handheld scraper. These end mills deburr pipe and tube for butt welds and shape rods for sliding into housings and holes.
Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. Also known as taper degree end mills, they're often used to machine angled slots in dies and molds.
Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material. Also known as taper degree end mills, they're often used to machine angled slots in dies and molds.
These tools have a tapered profile and rounded cutting edge for making smooth contours on intricate, three-dimensional shapes. They're also known as taper degree end mills. Made of solid carbide, they're harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material.
Also known as diagonal-cutting pliers.
Leverage points in both the jaws and the handle give you more power with less effort.
Choose these wire cutters for your occasional use.
For use where even minor magnetism can cause major damage, these wire cutters are made of titanium, so they’re completely nonmagnetic.
These cutters are stainless steel, which provides excellent corrosion resistance.
Cut steel, spring steel, and other hard wire without worrying about your wire cutters rusting.
Spot these cutters easily—colored grips make them stand out, so you don’t lose them.
The black finish prevents glare that can interfere with precision work under bright light and magnification.
These sets include four cutters, each with a different head shape.
The grips on these cutters drain static from your application, preventing buildup from electrostatic discharge (ESD).
These tools divert static electricity faster than our other static-control wire cutters.
The specially designed internal spring provides constant, uniform tension for superior performance.
Tungsten carbide cutting edges are bonded to the jaws for long life.
Make cuts easily and comfortably while protecting sensitive equipment from static discharge.
Made of aluminum-bronze that is Factory Mutual approved, these cutters inhibit sparking and are nonmagnetic and corrosion resistant.
Good for high-volume cutting and trimming.
These cutters have insulated grips to protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.
Make accurate cuts at precise angles. These cutters have a miter guide that is notched to line up your workpiece.
The handles are angled 90° from the blade so you can cut material from directly above tight spaces.
Keep your hand away from the material being cut.
Blades are high-speed steel so they stay sharp longer than steel blades, and they can be sharpened.
A double hinge provides high cutting force with low gripping pressure. These cutters are also known as aviation snips.
Sized and shaped like pliers, these sheet metal cutters are small enough to fit in your tool belt.
These cutters make straight cuts and curves.
Replace blades as they wear. These cutters are also known as tinners' snips.
Also known as bulldog snips, these have long handles and short blades for cutting through thick sheet metal with less effort than standard sheet metal cutters.
Handles are angled to keep your hand away from the material as you cut straight lines and curves.
Blades are tapered to give you more control when cutting straight lines, tight curves, and circles, and they're serrated to prevent slipping. These cutters are also known as duckbill snips.
Prevent waste from flying up as you work. A double blade makes two cuts to create a 7/64"-wide step that peels back, leaving little distortion and smooth edges.
This cutter has two blades that cut a 1/8" wide strip—peel it back for smooth edges with little distortion.
Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.
Also known a scissor-blade shears, the bottom blade remains stationary while the upper blade moves up and down to cut metal up to 1/64" thick with minimal material loss and edge distortion.
Minimize material loss and edge distortion with these scissor-like cutters that cut metal up to 1/64" thick.+
Use to cut patterns in flat material with minimal material loss and less effort compared to manual cutters.
A double blade creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.
Turn your workpiece while cutting to create curves and complex shapes.
Prevent chipping, binding, and fracturing when cutting brittle, high-pressure laminated plastic.
Make a flush cut that leaves a smooth, finished edge.
Mount this cutter to the floor and use it to cut through steel angle iron up to 2"×2"×1/4".
Leave clean cut edges in a variety of pliable materials.
Also known as nippers, these cutters have wide, flat jaws that cut steel wire and bolts close to the surface.
Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.
A double hinge provides high cutting force with low gripping pressure.
Make accurate, flush cuts through small wire with these tweezer-style cutters.
Plastic-cushioned grips make these cutters easy to hold during repeated cuts.
Cut hard steel wire, nails, and small rivets close to the surface with the wide, flat jaws on these cutters.
The carbide-tipped steel jaws stay sharp longer than standard steel jaws. You can sharpen them as they wear. These cutters have a double hinge that provides high cutting force with low gripping pressure.
These powerful cutters make diagonal cuts with a nipping action to cut extra-hard wire with ease.
Cut thin, hard wire with these small cutters.
Handle is angled 30° to keep work in sight and hands clear of the work surface. Blades are flat on one side for close-to-the-surface cuts.
The cutting head is angled 30° from the handles, so you can cut close to a surface or in a tight space without the handles getting in your way.
When there isn't clearance to use standard-grip pliers, the angled head on these tools gives you access. Also known as lineman’s and combination pliers, use them to pull, bend, and cut wire.
Extra-long handles enable access to hard-to-reach areas. Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.
Also known as lineman’s and combination pliers, use these tools to pull, bend, and cut wire.
Additional features, such as wire terminal crimpers, enable you to perform a variety of electrical wiring and installation work with a single tool. Also known as lineman’s and combination pliers, these pliers have long jaws that pull, bend, and cut wire and other small workpieces.
Deep serrations provide the firm grip necessary for pulling rebar tie wire, and the hook-shaped handle end keeps your hand from slipping off. Also known ironworkers’ pliers, these tools also bend and cut wire.
Avoid the potential for an arc flash or short circuit that can occur when using conventional insulated tools with metal components. Completely metal-free, these pliers are plastic with ceramic cutting blades. They are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Use to pull, bend, and cut wire.
Insulated grips protect against accidental contact with live electrical circuits. These pliers are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Use them to pull, bend, and cut wire.
Made of aluminum-bronze that is FM approved, these pliers satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Use them to pull, bend, and cut wire.
Secure a lanyard to the ring on the handle to prevent dropping your pliers when working at height. Use these tools to pull, bend, and cut wire.
Made of stainless steel or titanium, these pliers are good for environments where moisture and other contaminants are present.
Create beveled edges, contours, and cutouts on flat plates in order to prepare them for welding and give them a finished look.
Add these adapters onto cordless grinders in order to bevel smooth edges on plastic pipe and tubing, which help you create leak-tight cement connections.
Add smooth, beveled edges on plastic pipe and tubing to help you create leak-tight cement connections—these bevelers are quicker and more effective than files and power saws.
Lightweight and portable, these battery-powered bevelers cut faster than manual ones.
With more power than angle grinders, these vertical grinders quickly remove large amounts of stock, rust, scale, and other materials.
With no cord to limit mobility, you can take these battery-powered grinders wherever they’re needed.
More durable than our Light Duty Grinders, these are designed for more frequent use.
Use these grinders for light, intermittent grinding and sanding.
Rated for continuous use to take on tough jobs, these grinders have heavy duty gears for smooth operation and long tool life.
The threaded spindles on these grinders accept raised-hub grinding wheels.