Filter by
Roller Chain Trade Number
Link Type
Roller Diameter
Performance
DFARS Specialty Metals
RoHS
REACH
Lubrication
Export Control Classification Number (ECCN)
Low-Maintenance Roller Chain and Links
 |
Chain |
 |
Connecting Links |
 |
Adding-and-Connecting Links |
 |
Forget the mess and the stress, this chain has bearings that run reliably with little or no need for lubrication. Like the chain on a bike, the side plates have a figure-eight shape that grips sprockets to transmit power between rotating shafts without slipping.
Oil-Embedded Open Bearings—Made from porous bronze saturated with oil, these bearings don’t require lubrication.
Sealed Bearings—These bearings come with seals to retain the grease you add and reduce the need for additional lubrication. They also keep grease off your equipment and prevent dirt from sticking to the chain.
Steel—The go-to for roller chain, steel is strong and economical. It’s best for dry environments since moisture will cause it to rust.
Corrosion-Resistant Nickel-Plated Steel—A step up from plain steel, the nickel plating adds a layer of rust protection in wet environments. However, if scratched, the underlying steel may still rust. The plating may also hinder welding.
Connecting Link—Use a single link to join both ends of your chain. Start by removing the spring clip from the link’s side plate. Then, slide the link pins into the mating rollers at each end of your chain and snap the clip back on. Also known as master links.
Adding-and-Connecting Link—An all-in-one link for adding and connecting. It adds a half-pitch length at the roller end, allowing finer length adjustments than full-pitch links. The pin end connects to your chain. Remove the side plate to install. Also known as half links and offset links.
Roller Chain | Chain | Connecting Links | Adding-and-Connecting Links | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Trade No. | Std. | Pitch | Roller Dia. | Roller Wd. | Working Load, lb. | Lubrication | Per Ft. | Each | Each | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Oil-Embedded Open Bearings | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 40 | ANSI | 1/2" | 0.312" | 19/64" | 810 | Lubricated | 000000 | 000000 | 00000000 | 00000 | 00000000 | 000000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Corrosion-Resistant Nickel-Plated Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 40 | ANSI | 1/2" | 0.312" | 19/64" | 680 | Lubricated | 000000 | 00000 | 0000000 | 0000 | 0000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Sealed Bearings | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Steel | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 40 | ANSI | 1/2" | 0.312" | 5/16" | 830 | Required | 00000000 | 00000 | 000000000 | 0000 | 000000000 | 00000 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
