The enclosure on these jelly jar lights contains explosions, sparks, and flashes. These lights are safe to use in NEC Class I, II, and III, Division 1 hazardous locations.

Contain explosions, sparks, and flashes—the enclosure on these ceiling lights makes them safe to use in NEC Class I and II, Division 1 hazardous locations.

Mount these lights in large, open areas where flammable and combustible gases may be present, such as during leaks or ventilation failures. These lights are rated for use in NEC Class 1, Division 2 hazardous locations.

Safely light up chemical processing plants, mining operations, and other large areas where combustible gases and dust are present. These lights have an explosion-proof housing that contains sparks and flames, so they won’t react to nearby hazards.

Upgrade your fluorescent recessed lighting to energy-efficient LEDs without removing fixtures and exposing insulation.

No need for wiring—these lights plug into a standard wall outlet. Also known as shop lights.

Don’t waste energy lighting unoccupied spaces—these lights turn on when they detect movement.

Light up spaces that have no electrical connection or are difficult to wire, such as sheds and closets.

Link these lights together to create different shapes with a sleek look.

Brighten high-traffic areas with our most rugged ceiling lights. Rated IK10, the highest impact resistance rating, they’re protected by a 16-gauge cold-rolled steel frame and polycarbonate lens.

Maximize the light that reaches your shelving. Often used in storage rooms and warehouse rack rows, these lights have reflectors that direct all light downwards from ceilings up to 24 ft. high.

Illuminate steps to reduce the risk of tripping or falling, especially at night or in poorly lit areas.

Rated for over a decade of use well above 100° F, these linear bay lights long outlast standard facility lights in high heat.

Brighten large, open areas, such as warehouses and manufacturing spaces. IP rated and UL listed for wet locations, these lights are sealed against washdowns.

Create ambient and accent lighting with these sleek, modern lights that shine above, below, and around themselves.

Also known as sconces, these lights are a stylish choice for ambient and accent lighting in hallways and entryways. They’re UL or ETL listed for wet locations, so you can install them outdoors—rain and humidity won’t be a problem.

Tough enough for offshore rigs and seafaring vessels—yet less than half the height of typical jelly jar lights. Built with a thick aluminum housing and a tough polycarbonate lens, these lights withstand hard impact without a guard.

Illuminate areas that need frequent cleaning, such as food processing lines, with long rows of lights. Rated IP65, these lights have a sealed lens and liquid-tight end caps that protect them from low-pressure washdowns and dust.

Upgrade your traditional fluorescent washdown lights—these LEDs last longer and eliminate the need to replace bulbs.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust.

To keep contaminants from entering your clean room, these lights seal against drop ceilings with an airtight gasket.

Illuminate outdoor areas and objects such as parking lots, flag poles, and billboards.

Light up offshore rigs, coal mines, and other outdoor areas where gas, vapor, or dust could ignite. These lights have an enclosure that contains sparks and explosions, so they won’t react with nearby hazards.

No need for wiring—these lights plug-in with a three-prong plug.

See what’s happening outside your facility—day and night. These lights have a built-in video camera that records when they sense motion.

Powered by the sun, these security lights function in areas that don’t have access to electricity. They’re often used to shine light on parking lots, landscaping, signs, entryways, and other outdoor spaces.

Light up remote spaces without having to keep track of a new cordless tool battery. These floodlights run on a Milwaukee M18 battery (sold separately). These lights extend up to 7 ft. tall and have a pivoting head to direct light where you need it.

Brighten areas of a jobsite with these floodlights, and move them at a moment’s notice.

Compact and easy to carry, these ETL listed lights stand up to dripping, splashing, and falling liquids. The head adjusts up and down to direct light where it's needed.

Bring light to remote areas with the DeWalt rechargeable battery that's already in your toolkit.

Flood dark, remote jobsites with multiple tiers of light. These cordless lights stack on top of each other to focus a strong beam of light in one direction.

As bright as stadium lights, these floodlights are the most powerful in our offering—they’ll brighten jobsites half the size of a football field. They run on a diesel generator you can use to power other lights and tools in the field.

Light up large, open rooms where you need a quick setup and takedown, such as a room under construction. Just hang these lights from a ceiling up to 30' high and they’re ready to go.

Keep excess cords out of your way—the reel locks the cord at any length and retracts it when not in use.

Pop these lights on magnetic surfaces to brighten wet spaces. Rated NEMA 6 and ETL listed, you can splash, spray, or dunk them in water, and they’ll keep working.

Hang these lights where you need them on the job site.

A series of bulb heads are attached to a power cord to provide overhead lighting for job sites.

Power these lights with the same battery as your other cordless tools. They run on a Milwaukee M18 battery to light up work where there’s no outlet.

Because these lights are compatible with DeWalt rechargeable batteries, you can keep one type of cordless tool battery on hand. Their head pivots to aim light where it's needed in areas that don't have electrical power service.

Point light where it’s needed—even in wet areas. These lights are sealed against splashing and dripping water.

Flood hazardous areas with light—these lights are intrinsically safe, meaning they can’t cause an explosion or fire. Rated NEC Class I, II, III, and Zone 0, they’re safe to use in areas with ignitable concentrations of flammable or combustible gases, dust, and fibers.

Safely light up large spaces where combustible gases and dust are normally present. Rated NEC Class I and II, these lights have a housing that contains any sparks or flames and seals out ignitable gases, vapors, and dust.

Gooseneck arms can be repositioned faster and more easily than articulating arms.

Shine light on machinery and through the sight glass on tanks to inspect food, brewery, chemical, pharmaceutical, and bio-tech processing lines.

Light up your workspace when overhead lighting falls short.

Stretch the arm to bring light directly over your work—even across a large surface. Also known as articulating arm lights, these lights have rigid sections that hold their position steady, including when fully extended.

Clip or clamp these lights near your work to illuminate what you’re working on without lighting up the whole room. Powered by a rechargeable battery, they’re often used in spaces where an outlet isn’t available.

Create a high-intensity lighting system for inspecting small and microscopic parts. With a flexible fiber-optic cable, you can adjust these lights to direct light right where you need it, even in hard-to-reach spots.

Illuminate machines or monitor processes in environments that reach up to 210° F. These lights have a thick housing that acts as a heat sink to protect the LEDs and driver from overheating.

Mount these lights into a recessed opening on your machine—they sit flush against the surface for a streamlined appearance.

Illuminate machines and monitor processes where flammable and combustible gases, dust, or fibers are present—from paint spray booths to chemical plants. These lights have an enclosure that contains sparks, flashes, and explosions.

With a slimmer profile than other strip machine lights, these lights fit in tight spots inside machinery because they don’t have a circuit board.

Illuminate inline flow sights to inspect the color, clarity, and flow of liquids in food and beverage, brewery, chemical, and pharmaceutical processing lines.

Suspend these lights overhead or mount them above your workspace.

When the power goes out, these lights turn on. They have adjustable heads that illuminate the path toward exits during outages.

Installed in drop ceilings, these lights are often used in open workspaces where columns and walls are few and far between. Unlike traditional backup lights, they don’t require a vertical surface for mounting.

No hardwiring required—these backup lights plug into a standard outlet.

Install these lights in aircraft hangars, gas plants, and other facilities where flammable and combustible gases or dust may be present, such as leaks or ventilation failures. Rated NEC Class I, Division 2, they seal out gases but aren't built to contain explosions.

A motion sensor turns on these lights when an enclosure door is opened. Mount them inside cabinets, closets, and other enclosed spaces.

Brighten enclosures and small spaces like closets and drawers—no hardwiring or outlets needed. Powered by a rechargeable battery, these lights are easy to install and help save on maintenance costs.

Light up drawers and enclosures where power isn’t available—these lights are compact and powered by battery.

Safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust, these lights are rated NEC Class I, II, and III.

With built-in LEDs, these lights deliver all the brightness of larger dock lights in a low-profile design. A hinge stop keeps the arm from extending past the dock door, and the curved design fits around the track.