A spring delivers a constant, low-pressure flow of grease to your lubrication point, so it never runs dry.

Tighten the cover to dispense grease.

By releasing a precise amount of grease at regular intervals, these motor-driven dispensers make sure your machine always has the right amount of grease.

Use compressed air to dispense grease.

This gun comes filled with 2 oz. of lithium-thickened grease.

Dispense small amounts of grease with one of these compact guns.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Prime these guns faster than standard grease guns and use them with just one hand.

Dispense grease with the highest-pressure-rated gun we offer.

Dispense small amounts of grease with this compact gun.

These guns deliver twice as much grease per stroke than standard lever-grip guns.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Designed to lubricate linear motion components, such as slide bearings, guides, and ball screws, these guns work exclusively with THK grease cartridges and fittings.

A display allows you to monitor how much grease is dispensed.

Increase the pressure of your grease system when necessary to dispense thick grease and force grease through clogged fittings.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Customize these dispensers to serve up to 24 lubrication points from a single location.

A sealed design prevents contamination in dirty and dusty environments.

Thread these dispensers directly into bearing housings, pumps, and other machinery. Flip the lever to start and stop flow; turn the dial to adjust flow.

Serve multiple lubrication points from a single location.

For use in clean environments, these manifolds have multiple air vents that keep pressure balanced.

Deliver an equal amount of oil to multiple lubrication points at once.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

Use this dispenser to brush oil on chain, gears, and conveyors. Often used to replenish lubricant after washdowns.

Flip the lever to start and stop flow.

Mount these reservoirs directly to your machine, or use them with a flow-adjustment valve and brush to create a dispenser.

A sealed design prevents contamination in dirty and dusty environments. Install a line between the reservoir's pressure port and the lubricated equipment to balance pressure.

Air pressurizes the oil in the reservoir and atomizes the spray. Add a spray valve to direct the flow of oil.

Driven by an air-powered pump, this dispenser comes with an adapter to mount through a bung opening on a drum.

A needle dispensing tip provides fine control for lubricating small parts.

Pull the trigger on these oilers for easier one-hand operation than standard hand-held oil dispensers.

Often attached to differential pressure gauges to measure liquid level in tanks, these manifolds have two isolation valves with a pressure-equalizing valve between them. To isolate your differential pressure gauge for maintenance or calibration, shut off flow on both sides and equalize pressure in the manifold. They are rated for at least 6,000 psi. Use with water, oil, air, and inert gas.

Also known as block and bleed valves, these have two vent ports to isolate pressure gauges, switches, and other components in high-pressure systems for maintenance, calibration, and sampling without interrupting the process. They are rated for up to 10,000 psi. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

The color-coded threads and numerical markings on these valves ensure consistent and repeatable settings. One full revolution of the handle reveals a new color to indicate the set point. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

With a gauge port on each side of these valves, you can install two different pieces of instrumentation equipment to simultaneously monitor multiple media properties without interrupting flow. Use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Rated for nearly twice the maximum temperature of standard threaded precision flow-adjustment valves, these can handle up to 700° F. They’re for use with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

To ensure highly precise flow adjustment, these valves adjust flow in smaller increments than other valves for finer control over the flow rate in metering and sampling applications. Use them with water, oil, air, and inert gas.

Solder these valves to tubing for a permanent, leak-tight connection. Use them with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Use these valves with NPT threaded pipe. They have a fluoroelastomer seal and a plastic body to withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For extra gripping power and a strong seal, these valves have Yor-Lok fittings with two sleeves that bite into tubing as you tighten the nut. All are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings. The 316 stainless steel body and seal, the PTFE seat and packing, and the Monel needle can withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Often used in low-pressure water pipelines, these valves have a plastic body for the lightest weight of our flanged flow-adjustment valves. Use them with water. They bolt to flanges to adjust and regulate flow in flanged pipelines.

These valves are for use with water, oil, air, and inert gas. They bolt to flanges to adjust and regulate flow in flanged pipelines.

Also known as proportional V-ball valves, these have a motor that adjusts and regulates flow in applications with higher flow rates and pressures than solenoid valves. As you increase the intensity of the electrical signal, the motor opens the valve, moving a ball with a V-cut opening that proportionately allows more flow as the valve opens. They're often integrated into PLC systems for automatic control over the valve position based on system conditions.

Solder these valves to copper tubing for a permanent, leak-tight connection. Use them with water and oil. All gradually open and close to adjust and regulate flow.

Also known as whistle valves, these open and throttle as force is applied to the lever and automatically close upon release. They’re commonly used for spraying, washing, and other applications that require manual discharge of liquid and air. Use with water, oil, air, and inert gas.

Rated for twice the pressure of other threaded flow-adjustment valves, these are often used in refineries and other demanding environments. Use with water, oil, air, and inert gas. They gradually open and close to adjust and regulate flow.

Plastic provides a lightweight and corrosion-resistant alternative to metal. Use with oil. These valves gradually open and close to adjust and regulate flow.