2 27/32" Housing ID Bearings

Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place. For high-speed applications, consider clamp-on shaft mounts, which are less likely to slip.

Clamp-On Shaft Mount—The clamp tightens around the shaft for a strong 360° grip. These mounts attach more securely than set screws to reduce vibration. Plus, there aren't any screws pressing into the shaft, so it stays free from damage. Also known as a concentric lock.

Black-Oxide Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.

				Retaining Ring						Temp. Range, ° F
	For Shaft Dia.	For Housing ID	Wd.	OD	Thk.	Bearing Seal Type	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Bearing Trade No.		Each
Set-Screw Shaft Mount







				Black-Oxide Steel

				1 1/4"	2 27/32"	15/16"	3.078"	0.063"	Sealed	Not Rated	5,750	5,000	-20	250	ER20	0000000	000000


				1 3/8"	2 27/32"	15/16"	3.078"	0.063"	Shielded	1	6,400	5,000	-40	250	ER22	0000000	000000
				1 7/16"	2 27/32"	15/16"	3.078"	0.063"	Sealed	Not Rated	5,750	5,000	-20	250	ER23	0000000	00000


				Clamp-On Shaft Mount







								Black-Oxide Steel

								1 1/4"	2 27/32"	15/16"	3.078"	0.063"	Sealed	1	5,750	6,500	-20	220	ER20	0000000	000000


								1 7/16"	2 27/32"	15/16"	3.078"	0.063"	Sealed	1	5,750	6,500	-20	220	ER23	0000000	000000

Quick-Mount Ball Bearings for Food and Beverage

Set-Screw Shaft

Mount

Clamp-On Shaft

Mount

You don't need any special tools to install these bearings in food production areas. Slip them onto a shaft and secure with the turn of a screw for easy mounting. Greased with NSF-registered H1 lubricant, these bearings are safe to install on food-processing equipment, such as conveyor belts, so long as they don’t directly touch the food. They're IP69K rated, so they'll stand up to the hot water from a pressure washer when cleaning your facility at the end of the day.

Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place. For high-speed applications, consider clamp-on shaft mounts, which are less likely to slip.

Corrosion-Resistant Nickel-Plated Steel—These bearings resist mild chemicals, such as the ammonia in cleaning solutions, while maintaining the strength of steel. The nickel coating can wear or chip over time, though. If it does, the steel beneath will rust quickly.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

				Retaining Ring						Temp. Range, ° F
	For Shaft Dia.	For Housing ID	Wd.	OD	Thk.	Bearing Seal Type	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Enclosure Rating	Food Industry Std.		Each
Set-Screw Shaft Mount







				Corrosion-Resistant Nickel-Plated Steel

				1 7/16"	2 27/32"	15/16"	3.078"	0.063"	Sealed	1	5,750	2,000	-20	220	IP69K	NSF Registered H1	0000000	0000000


				Clamp-On Shaft Mount







								Corrosion-Resistant Nickel-Plated Steel

								1 1/4"	2 27/32"	15/16"	3.078"	0.063"	Sealed	1	5,750	2,000	-20	220	IP69K	NSF Registered H1	0000000	000000