35mm Housing ID Bearings

Smoother than smooth—the balls inside these bearings roll nearly friction-free. You’ll often find them on rapidly rotating parts, from the whirring chuck on a power drill to the spinning shaft on an electric motor.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

Corrosion-Resistant 440C Stainless Steel—Combine the strength of steel with the corrosion resistance of stainless steel. These bearings won't degrade from water or mild chemicals, such as the ammonia in cleaning solutions. However, they'll weaken when exposed to salt water and harsh chemicals, such as bleach.

Highly Corrosion-Resistant 316 Stainless Steel—The most corrosion-resistant metal bearings we offer. They won't pit or weaken from salt water or harsh chemicals, such as bleach and chlorine found in cleaning solutions.

ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Open







				Steel

				15	35	11	1	1,750	26,000	-20	230	Standard	6202	00000000	00000


				17	35	10	1	1,300	28,000	-20	230	Standard	6003	00000000	00000




						Corrosion-Resistant 440C Stainless Steel

						15	35	11	1	1,150	20,000	-40	240	Standard	6202	00000000	00000


						17	35	10	1	1,100	24,000	-40	240	Standard	6003	00000000	00000




								Highly Corrosion-Resistant 316 Stainless Steel

								15	35	11	Not Rated	200	1,000	-40	140	Standard	6202	0000000	00000


								17	35	10	Not Rated	200	1,000	-40	140	Standard	6003	0000000	00000


								Shielded







												Steel

												10	35	11	3	1,900	26,000	-20	230	Standard	6300-2Z	0000000	00000


												15	35	11	1	1,750	20,000	-20	230	Standard	6202-2Z	00000000	0000
												15	35	11	3	1,800	22,000	-20	230	Standard	6202-2Z	0000000	00000
												17	35	8	1	1,400	31,000	-20	230	Standard	16003-2Z	00000000	00000
												17	35	10	1	1,300	22,000	-20	230	Standard	6003-2Z	00000000	0000
												17	35	10	3	1,400	22,000	-20	230	Standard	6003-2Z	0000000	00000




														Corrosion-Resistant 440C Stainless Steel

														10	35	11	1	1,500	23,000	-40	240	Standard	6300-2Z	00000000	00000


														15	35	11	1	1,150	20,000	-40	240	Standard	6202-2Z	0000000	00000
														17	35	10	1	1,100	20,000	-40	240	Standard	6003-2Z	00000000	00000


Sealed







														Steel

														10	35	11	3	1,900	15,000	-20	210	Standard	6300-2RS	00000000	00000


														15	35	11	3	1,800	13,000	-30	210	Standard	6202-2RS	00000000	00000
				15										35	11	3	2,000	19,400	-4	212	Standard	6202-2RS	00000000	0000
				15	35									14	1	1,800	14,000	-20	230	Standard	62202-2RS	00000000	00000
				17	35									10	1	1,300	11,800	-20	230	Standard	6003-2RS	0000000	00000
				17	35									10	3	1,400	13,000	-30	210	Standard	6003-2RS	0000000	00000




														Corrosion-Resistant 440C Stainless Steel

						15								35	11	1	1,450	20,000	-40	240	Standard	6202-2RS	0000000	00000

Permanently Lubricated Ball Bearings

Install and forget these self-lubricating bearings. Their lubricant is a solid material that fills the space between the balls and releases oil over time, so you'll never need to add more.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Open







				Steel

				15	35	11	1	1,450	12,000	10	200	Standard	6202	00000000	000000


				17	35	10	1	1,100	11,500	10	200	Standard	6003	00000000	00000




						Corrosion-Resistant 440C Stainless Steel

						10	35	11	1	1,400	13,000	-10	200	Standard	6300	00000000	00000


						15	35	11	1	1,300	12,000	-10	200	Standard	6202	00000000	00000
						17	35	10	1	1,180	11,000	-10	200	Standard	6003	00000000	00000


						Sealed







										Steel

										10	35	11	1	1,400	13,000	10	200	Standard	6300-2RS	00000000	00000


										15	35	11	1	1,450	12,000	10	200	Standard	6202-2RS	00000000	00000
										17	35	10	1	1,100	11,500	10	200	Standard	6003-2RS	00000000	00000




												Corrosion-Resistant 440C Stainless Steel

												10	35	11	1	1,400	13,000	-10	200	Standard	6300-2RS	00000000	00000


												15	35	11	1	1,300	12,000	-10	200	Standard	6202-2RS	00000000	00000
												17	35	10	1	1,150	11,000	-10	200	Standard	6003-2RS	00000000	00000

Self-Aligning Ball Bearings

Open

Sealed

Misalignments correct themselves on the fly in these bearings. Two rows of balls have separate raceways in the inner ring and a shared raceway in the outer ring, so the balls rock back and forth to compensate for misalignment. This construction also reduces noise and vibration.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

								Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Misalignment Capability	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Open







				Steel

				10	35	17	1	2,050	18,000	4°	Not Rated	210	Standard	2300	00000000	000000


				15	35	11	1	1,700	18,000	4°	Not Rated	210	Standard	1202	00000000	00000
				15	35	14	1	1,950	26,000	2.5°	-30	210	Standard	2202	0000000	000000


				Sealed







								Steel

								15	35	14	1	1,650	14,000	1.5°	-30	210	Standard	2202-2RS	0000000	000000

Angular Contact Ball Bearings


Single Row Open	Single Row Sealed	Double Row Open	Double Row Shielded	Double Row Sealed

Support radial and thrust loads at the same time. These bearings are often found inside equipment such as gearboxes and pumps. For example, a bearing inside a gearbox withstands a radial load when the gear is engaged and a momentary thrust load when you shift to a new one. While they don't handle as much force from radial loads as standard bearings, you can pair them with a cylindrical roller bearing to increase their load capacity.

Single Row—Single-row bearings withstand thrust loads from one direction.

Double Row—Double-row bearings handle thrust loads from both directions.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

										Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Material	Dynamic Combined Load Cap., lbf	Max. Rotation Speed, rpm	Lubrication	Contact Angle	Min.	Max.	Bearing Trade No.		Each
Single Row







				Open

				15	35	11	3	Steel	1,850	24,000	Required	40°	-40	300	7202	0000000	000000




						Sealed

						15	35	11	1	Steel	1,850	24,000	Lubricated	40°	-20	230	7202-2RS	0000000	000000


						Double Row







										Open

										15	35	15.9	1	Steel	2,500	17,000	Required	30°	-40	250	3202	00000000	00000




												Shielded

												15	35	15.9	1	Steel	2,500	18,000	Lubricated	30°	-40	250	3202-2Z	00000000	000000




														Sealed

														15	35	15.9	1	Steel	2,500	14,000	Lubricated	30°	-40	210	3202-2RS	00000000	000000

Dry-Running Flanged Ball Bearings

Shielded

Don't risk your bearing popping out of place or making a mess. The flange presses against the housing wall, so vibration and other sudden forces parallel to the shaft (thrust loads) won't knock these bearings off-kilter. Made of naturally slippery plastic, there's no lubricant to maintain. No lubricant means no oil that could drip off, wash out, or collect dust, so they're ideal for spic-and-span spaces. They stand up to thorough cleanings since they won't rust or warp from moisture.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Acetal—The most common choice for plastic bearings, acetal is economical yet still stands up to daily wear and tear.

316 Stainless Steel Balls—Won't corrode from salt water or harsh chemicals, such as bleach and chlorine found in cleaning solutions.

				Flange, mm				Temp. Range, ° F				316 Stainless Steel Balls
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	OD	Thk.	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	ABEC Rating	Bearing Trade No.		Each
Shielded







				Acetal

				10	35	9	38	2	25	1,900	-40	175	Not Rated	6000	00000000	000000


				12	35	9	38	2	30	1,700	-40	175	Not Rated	6001	00000000	00000

Ball Bearings with Retaining Ring

Shielded

Sealed

No need for complicated tools—install these bearings by hand inside a housing. The ring stops the bearing from being jostled out of place when it experiences sudden forces parallel to the shaft (thrust loads).

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

				Retaining Ring, mm					Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	OD	Thk.	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Shielded







				Steel

				15	35	11	39.7	1.12	1	1,800	22,000	-20	230	Standard	6202-2Z	0000000	000000


				Sealed







								Steel

								15	35	11	39.7	1.12	1	1,800	13,000	-40	210	Standard	6202-2RS	0000000	00000


								17	35	10	39.7	1.12	1	1,400	13,000	-40	210	Standard	6003-2RS	0000000	00000

High-Load Dry-Running Ball Bearings

Double the balls for double the load capacity—these bearings carry twice as much weight as standard dry-running ball bearings. Made of naturally slippery plastic, there's no lubricant to maintain. No lubricant means no oil that could drip off, wash out, or collect dust, so they're ideal for spic-and-span spaces. They stand up to thorough cleanings since they won't rust or warp from moisture.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, reducing wear and extending the life of the bearing.

Acetal—The most common choice for plastic bearings, acetal is economical yet still stands up to daily wear and tear.

316 Stainless Steel Balls—Won't corrode from salt water or harsh chemicals, such as bleach and chlorine found in cleaning solutions.

						Temp. Range, ° F				316 Stainless Steel Balls
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	ABEC Rating	Bearing Trade No.		Each
Open







				Acetal

				15	35	16	85	800	-40	180	Not Rated	A5202-6	00000000	000000

Ball Bearings for Food and Beverage

Sealed

Food production rolls along smoothly on these bearings. Greased with FDA-compliant lubricant, they’re safe to install on food-processing equipment, such as conveyor belts, so long as they don’t directly touch the food. The lubricant is a solid material that fills the space between the balls and releases oil over time, so you'll never need to add more.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Food Industry Std.	Bearing Trade No.		Each
Sealed







				Corrosion-Resistant 440C Stainless Steel

				10	35	11	1	1,500	13,000	-40	200	Standard	FDA Compliant 21 CFR 178.3570	6300-2RS	00000000	000000


				15	35	11	1	1,450	12,000	-40	200	Standard	FDA Compliant 21 CFR 178.3570	6202-2RS	00000000	00000
				17	35	10	1	1,100	11,000	-40	200	Standard	FDA Compliant 21 CFR 178.3570	6003-2RS	00000000	00000

High-Precision Angular Contact Ball Bearings

Open

Our most precise bearings for tackling radial and thrust loads at once, with tolerances tighter than a speck of dust. Rated ABEC 7 out of 9, they meet strict tolerance standards established by the Annular Bearing Engineers Committee (ABEC). Choose them for equipment that requires both high speed and pinpoint accuracy, such as machine tool spindles. For example, a bearing on a spindle withstands a radial load as it spins at high speeds and a thrust load when the cutting tool touches the workpiece. These bearings don’t handle as much force from radial loads as standard ones, but you can pair them with a cylindrical roller bearing to increase their load capacity.

Single Row—Single-row bearings withstand thrust loads from one direction.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

										Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Material	Dynamic Combined Load Cap., lbf	Max. Rotation Speed, rpm	Lubrication	Contact Angle	Min.	Max.	Bearing Trade No.		Each
Single Row







				Open

				15	35	11	7	Steel	2,000	46,000	Required	15°	-40	245	7202	0000000	0000000


				17	35	10	7	Steel	1,500	50,000	Required	15°	-30	140	7003	0000000	000000

One-Way-Locking Ball Bearings

Shielded

Sealed

Prevent shafts from reversing direction. These bearings have internal components (sprags) that lock against the outer ring to transmit torque one way but spin freely in the other. They're often found in backstopping, indexing, and overrunning applications. For example, they're used to prevent conveyors from reversing.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

								Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Max. Torque, ft·lbf	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Shielded







				Steel

				15	35	11	1	1,160	9,400	15	-40	170	Standard	FZ 6202	0000000	0000000


				Sealed







								Steel

								15	35	16	1	1,160	8,400	15	-40	170	Standard	FZ 6202 2RS	0000000	000000

Electrically Insulating Ball Bearings

Sealed

Protect bearings from stray currents. The ceramic balls insulate bearings from electrical charges in electric motors and power generators that can damage the inner ring over time. The balls also generate less heat than metal ones, so you don’t have to lubricate them as often to keep bearings running smoothly.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

							Temp. Range, ° F			Ceramic Balls
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Bearing Trade No.		Each
Sealed







				Steel

				15	35	11	1	1,800	22,000	-40	210	6202-2RS	0000000	0000000


				17	35	10	1	1,400	22,000	-40	210	6003-2RS	0000000	000000

Dry-Running Ball Bearings

Made of naturally slippery plastic so there's no lubricant to maintain or make a mess. These bearings are ideal for spic-and-span spaces since oil won't drip off, wash out, or collect dust over time. They won't rust or warp from moisture, so they stand up to thorough cleanings.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, reducing wear and extending the life of the bearing.

Acetal—The most common choice for plastic bearings, acetal is economical yet still stands up to daily wear and tear.

316 Stainless Steel Balls—Won't corrode from salt water or harsh chemicals, such as bleach and chlorine found in cleaning solutions.

Glass Balls—Nonmagnetic, so they won't interfere with sensors and other sensitive electronics.

						Temp. Range, ° F				316 Stainless Steel Balls		Glass Balls
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	ABEC Rating	Bearing Trade No.		Each		Each
Open







				Acetal

				15	35	11	65	1,000	-40	180	Not Rated	6202	0000000	000000	00000000	000000


				17	35	8	65	1,000	-40	180	Not Rated	16003	00000000	00000	———	0
				17	35	10	65	1,000	-40	180	Not Rated	6003	00000000	00000	———	0

High-Temperature Graphite-Lubricated Ball Bearings

Keep parts spinning in industrial ovens and other places as hot as 660° F. Greased with graphite lubricant, these bearings stay slippery where oil would burn off or solidify. You can install and forget them since the lubricant lasts forever.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Shielded







				Steel

				15	35	11	1	1,800	350	-70	660	Standard	6202-2Z	0000000	0000000

Needle-Roller Bearings

Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.

Open Bearing—Open bearings dissipate heat more efficiently than sealed bearings.

				Radial Load Cap., lb.
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	For Shaft Surface Smoothness, Ra, μin	Temp. Range, ° F	Specs. Met		Each
For Radial Load—Open with Steel Ring



		28	35	16	3,650	5,950	9,200	Required	8	-20 to 280	DIN 618, ISO 3245	0000000	000000


		28	35	20	4,650	8,050	9,200	Required	8	-20 to 280	DIN 618, ISO 3245	00000000	00000

Oil-Embedded Sleeve Bearings

Install and forget these self-lubricating bearings. All are made from porous metal and saturated with oil to reduce maintenance and downtime. A good all-around choice, they are used in everything from palm-sized fans in electronics to tire-sized pulleys. Although these bearings will work in most conditions, oil may drip away if temperatures get too high. Consider a graphite-lubricated bearing for higher temperatures or places where you can’t afford the mess. All are fabricated, lubricated, and inspected in the U.S.

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.

High-Load 863 Iron Copper—Iron makes these bearings harder, stronger, and more resistant to sudden starts and stops than 841 bearing bronze. However, they operate at slower speeds. The increased iron content makes these bearings appear silver.

Extreme-Load Heat-Treated Iron Copper—Our strongest oil-embedded sleeve bearings. They’re heat treated to form a uniform internal grain that makes them stronger than 863 iron copper. As a result, they’re often used to support extreme loads in earth-moving equipment and railroad applications. The increased iron content makes these bearings appear silver.

Mineral Oil Base—Mineral oil consistently lubricates at most temperatures but doesn’t last as long as synthetic oil.

Synthetic Oil Base—A high-quality lubricant makes all the difference. Synthetic oil is less sensitive to temperature changes than mineral oil, so it won't get runny and leak away at higher temperatures.

	For Housing ID, mm	Lg., mm	Dynamic Radial Load Cap. @ Speed	Base Oil	Temp. Range, ° F		Each
841 Bearing Bronze



	25	35	25	1,900 lb. @ 60 rpm	Synthetic Oil	-35 to 300	00000000	00000


	25	35	30	2,300 lb. @ 60 rpm	Synthetic Oil	-35 to 300	00000000	00000
	25	35	35	2,700 lb. @ 60 rpm	Synthetic Oil	-35 to 300	00000000	00000
	25	35	50	3,850 lb. @ 60 rpm	Synthetic Oil	-35 to 300	00000000	00000
	30	35	25	2,300 lb. @ 30 rpm	Synthetic Oil	-35 to 300	00000000	0000
	30	35	30	2,750 lb. @ 30 rpm	Synthetic Oil	-35 to 300	00000000	0000


	High-Load 863 Iron Copper



			25	35	25	2,150 lb. @ 60 rpm	Synthetic Oil	-15 to 300	00000000	00000


			Extreme-Load Heat-Treated Iron Copper



					25	35	25	4,650 lb. @ 60 rpm	Mineral Oil	10 to 220	00000000	00000

Sleeve Bearings

These bearings don’t come with a lubricant, so you can select the oil that meets the needs of your application. You’ll need to refill the oil, so make sure the bearing is located where you can access it. All are fabricated and inspected in the U.S.

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

High-Load 932 Bearing Bronze—These bearings are strong enough for sudden starts and stops, plus they resist wear and tear. They are cast from an alloy of leaded tin bronze for uniform rigidity and strength. Also known as 660 leaded bronze bearings.

High-Load Chemical-Resistant 954 Bearing Bronze—The strongest of our bronze bearings. The addition of iron and aluminum makes them exceptionally strong and resistant to chemicals. They’re often used in the most demanding environments, such as salt mines. Also known as aluminum bronze.

	For Housing ID, mm	Lg., mm	Dynamic Radial Load Cap. @ Speed	Temp. Range, ° F		Each
High-Load 932 Bearing Bronze



	25	35	25	3,850 lb. @ 60 rpm	-350 to 450	00000000	000000


	25	35	40	6,200 lb. @ 60 rpm	-350 to 450	00000000	00000
	25	35	100	15,500 lb. @ 60 rpm	-350 to 450	00000000	00000
	28	35	25	4,300 lb. @ 30 rpm	-350 to 450	00000000	00000
	28	35	40	6,900 lb. @ 30 rpm	-350 to 450	00000000	00000


	High-Load Chemical-Resistant 954 Bearing Bronze



			28	35	100	19,500 lb. @ 30 rpm	-350 to 500	00000000	00000

Grooved Sleeve Bearings

A figure-8-shaped groove provides a flow path for lubricant and distributes it evenly inside the bearing’s surface. A refill hole on the outside lets you inject your lubricant straight into the groove. These bearings don’t come with a lubricant, so you can select the oil that meets the needs of your application. You’ll need to refill the oil, so make sure the bearing is located where you can access it. All are fabricated and inspected in the U.S.

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

	For Housing ID, mm	Lg., mm	Dynamic Radial Load Cap. @ Speed	Temp. Range, ° F		Each
High-Load 932 Bearing Bronze



	25	35	25	3,350 lb. @ 60 rpm	-350 to 450	00000000	000000


	25	35	40	5,400 lb. @ 60 rpm	-350 to 450	00000000	00000

Dry-Running Sleeve Bearings

Made of naturally slippery plastic so you’ll never have to add lubricant. They’re ideal for clean environments where you need to prevent oil drips or graphite flakes. Compared to metal bearings, they are lighter and will never rust.

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

Nylon—The most popular choice, nylon is wear resistant yet economical. Keep in mind, though, that it will swell and weaken when exposed to moisture.

								Each
	For Shaft Dia., mm	For Housing ID, mm	Lg., mm	Dynamic Radial Load Cap. @ Speed	Color	Temp. Range, ° F		1-24	25-99	100-Up
Nylon



		25	35	30	185 lb. @ 60 rpm	Off-White	-10 to 220	00000000	000000	000000	000000


		30	35	25	310 lb. @ 30 rpm	Off-White	-10 to 220	00000000	00000	00000	00000
		30	35	30	370 lb. @ 30 rpm	Off-White	-10 to 220	00000000	00000	00000	00000

Dry-Running Metal-Reinforced Plastic Sleeve Bearings

Combine slippery plastic with the strength of metal. The PTFE core is naturally slippery, so you’ll never have to add lubricant. These bearings also keep your workspace clean with no lubricant to drip or flake and attract dust. Compared to all-metal bearings, they are lighter.

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

PTFE with Aluminum Shell—A lightweight upgrade from our steel shell. These bearings also offer good corrosion resistance similar to stainless steel but aren’t as strong.

	For Housing ID, mm	Lg., mm	Dynamic Radial Load Cap. @ Speed	Temp. Range, ° F		Each
PTFE with Aluminum Shell



	30	35	25	2,500 lb. @ 30 rpm	-400 to 400	00000000	000000


	30	35	30	3,000 lb. @ 30 rpm	-400 to 400	0000000	000000

High-Temperature Graphite-Lubricated Sleeve Bearings

Made of a graphite and metal alloy, these bearings stay slippery at high temperatures where oil burns off and other bearings fail. With no need for refills, they require little to no maintenance. You’ll find them in pumps, propellers, and mixers that spin near steam or inside ovens. However, graphite may eventually flake off, dropping flecks and leaving smudges. If you need a spic-and-span space, consider dry-running bearings made of slippery plastic instead. All are fabricated, lubricated, and inspected in the U.S.

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

	For Housing ID, mm	Lg., mm	Dynamic Radial Load Cap. @ Speed	Temp. Range, ° F		Each
High-Load 932 Bearing Bronze



	25	35	50	6,750 lb. @ 60 rpm	-350 to 450	00000000	000000

Oil-Embedded Sleeve Bearings for Food and Beverage

These lead-free bearings are infused with a food-grade oil that is odorless, colorless, tasteless, and safe for unintended contact with food. They’re often used in food and beverage processing, packing, and handling equipment. All are made from porous metal and saturated with oil to reduce maintenance and downtime. If you need a bearing rated for contact with food, consider dry-running sleeve bearings for food and beverage. All are fabricated, lubricated, and inspected in the U.S.

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

	For Housing ID, mm	Lg., mm	Dynamic Radial Load Cap. @ Speed	Base Oil	Temp. Range, ° F	Specs. Met		Each
High-Load 863 Iron Copper



	25	35	35	3,050 lb. @ 60 rpm	Synthetic Oil	-75 to 300	FDA Compliant 21 CFR 178.3570, ASTM B439	00000000	000000