McMaster-Carr logo
    Filter by
    System of Measurement
    Shaft Diameter
    Attribute Image
    Bearing Type
    Industrial Info Compare
    For Housing ID
    Attribute Image
    Plain Bearing Type
    Dynamic Radial Load Capacity
    Width
    Attribute Image
    Shaft Mount Type
    Bearing Construction
    Bearing Seal Type
    Length
    Attribute Image
    Static Radial Load Capacity
    Ball Bearing Profile
    Lubricant
    Shaft Type
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    2 Products

    Four-Point Angular Contact Ball Bearings

    Image of Product. Front orientation. Ball Bearings. Four-Point Angular Contact Ball Bearings.
    Support complex movement in multiple directions with a single compact bearing. The balls distribute weight at four points, so these bearings handle radial, thrust, and moment loads all at once. For example, you’ll often find them in robot arms, which rotate, extend, and twist while supporting an object’s weight. Thinner than two standard angular contact ball bearings paired together, these bearings squeeze into tight spaces. They’re commonly paired with large hollow shafts to run electrical wire and other lines.
    Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Dynamic
    Load Cap.
    Temp.
    Range, ° F
    For Shaft
    Dia.
    For Housing
    ID
    Wd.
    ABEC
    Rating
    Radial,
    lb.
    Thrust,
    lb.
    Moment,
    ft·lbf
    Max. Rotation
    Speed, rpm
    Contact
    Angle
    Min.
    Max.
    Inner Ring
    Type
    Each
    Open
     
    Steel
    4"4 1/2"1/4"1F7501,20010060030°-60250Standard00000000000000
     

    Oil-Embedded Sleeve Bearings

    Image of Product. Front orientation. Sleeve Bearings. Oil-Embedded Sleeve Bearings.
    Install and forget these self-lubricating bearings. All are made from porous metal and saturated with oil to reduce maintenance and downtime. A good all-around choice, they are used in everything from palm-sized fans in electronics to tire-sized pulleys. Although these bearings will work in most conditions, oil may drip away if temperatures get too high. Consider a graphite-lubricated bearing for higher temperatures or places where you can’t afford the mess. All are fabricated, lubricated, and inspected in the U.S.
    With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.
    841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.
    Mineral Oil Base—Mineral oil consistently lubricates at most temperatures but doesn’t last as long as synthetic oil.
    For Shaft
    Dia.
    For Housing
    ID
    Lg.
    Dynamic Radial Load
    Cap. @ Speed
    Base Oil
    Temp. Range,
    ° F
    Each
    841 Bearing Bronze
    4"4 1/2"4"25,450 lb. @ 30 rpmMineral Oil10 to 220000000000000000
     
    back to top