These bearings have the highest speed ratings of any mounted ball bearing that we offer. The clamp-on collar creates a 360° grip around the shaft for a strong, mar-free hold. Bearings are self-aligning to compensate for shaft misalignment.

Sealed bearings block out dust and other contaminants better than shielded bearings.

For technical drawings and 3-D models, click on a part number.

Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants. All have NSF registered H1 lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications. Made of 316 stainless steel, they resist corrosion and prevent rusting caused by salt water, chlorine solutions, and chemicals.

Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw does leave some marring on shafts.

Clamp on bearings have a locking collar to center shafts and secure them better than set screw bearings, so there’s less vibration and noise. To install them, tighten the locking collar’s screw until it grips the inner ring.

Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, won’t absorb water, and are FDA compliant.

For technical drawings and 3-D models, click on a part number.

A split housing means you can remove the top half of these bearings to inspect or repair shafts and components. This reduces downtime and minimizes the risk of damaging surrounding components.

Bearings for radial loads accommodate minor changes in your shaft’s length as it expands and contracts from your machinery heating up and cooling down. They are typically used in assemblies with long shafts and positioned away from the drive end.

Bearings for combined radial and thrust loads anchor the shaft in position and absorb the thrust load. However, they are not designed to handle your shaft expanding and contracting. They’re typically mounted near the drive side of an assembly.

For technical drawings and 3-D models, click on a part number.

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

Bearings with a set-screw shaft mount secure to shafts with no need for an additional collar. They can be used for bi-directional shaft rotation when applications require reversing action. The set screw may cause some marring on the shaft.

For technical drawings and 3-D models, click on a part number.

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.

For technical drawings and 3-D models, click on a part number.

Made to withstand frequent washdowns, these bearings are permanently lubricated, which means you’ll never have to add lubricant. Use them in hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. With a 316 stainless steel housing, these bearings won’t rust from salt water, chlorine, or chemicals. All are lubricated with NSF registered H1 grease, which is certified for incidental contact with food.

Concentric-lock bearings have a collar that centers and secures the shaft in the bearing bore. To install, tighten the single screw on the collar around its inner ring on your shaft. These bearings have a secure grip on the shaft that reduces vibration and noise.

For technical drawings and 3-D models, click on a part number.

Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants. They have excellent corrosion resistance and prevent rusting caused by salt water, chlorine solutions, and chemicals because their housing is 316 stainless steel. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.

Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw does leave some marring on shafts.

Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, won’t absorb water, and are FDA compliant.

For technical drawings and 3-D models, click on a part number.

Combine with threaded pipe to mount these bearings in a variety of positions without the need for a flat mounting surface. Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.

NPSM (National Pipe Straight Mechanical) threads are compatible with NPT threads. See more about pipe thread type and sizing.

For technical drawings and 3-D models, click on a part number.

Add on to an existing screw conveyor or keep it running like new.

Screws are designed for right-hand operation. Screws with a thicker edge offer longer service life for abrasive materials.

Discharge spouts can be welded to a cutout in the trough.

Coupling shafts connect two screws together. End shafts support the end conveyor section. Coupling bolts connect shafts to the screw.

End-shaft seals prevent material contamination and discharge.

End-shaft bearings support the end of the shaft and help the screw rotate.

Bearing hangers mount inside the trough.

Hardwood bearings are oil impregnated and are often used in agricultural applications. UHMW bearings work well with chemicals and wet environments. Iron bearings are oil impregnated and offer longer life for abrasive materials. Bronze bearings are oil impregnated.

For technical drawings and 3-D models, click on a part number.