About Ball and Roller Bearings
More
Set Screw Collar Ball Bearings



Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.
Bearings with a black-oxide steel ring have some corrosion resistance.
Sealed bearings block out dust and other contaminants better than shielded bearings.
Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.
Flanged bearings have a flange that ensures proper positioning inside a tube or housing.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | ABEC Rating | Each | |
Sealed (Lubricated) | ||||||||||||||
Black-Oxide Steel—With Retaining Ring | ||||||||||||||
ER27 | 1 11/16" | 3.347" | 1 3/32" | 2.2969" | 1.9375" | 3 19/32" | 0.0625" | 7,900 | 5,100 | 3,800 | -20° to 220° | ABEC-1 | 0000000 | 0000000 |
Steel—Flanged | ||||||||||||||
GYA111RRB | 1 11/16" | 3.3465" | 0.866" | 2.2813" | 1.6555" | __ | __ | 8,150 | 4,500 | 4,000 | -65° to 250° | ABEC-1 | 0000000 | 000000 |
One-Piece Thrust Ball Bearings

In addition to handling higher loads than three-piece ball bearings, one-piece bearings are easier to handle. They have an outer band that holds the bearing together and acts as a shield against dust and other contaminants.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Features | Each | |
Shielded | |||||||||||
1 11/16" | 1 31/32" | 13/16" | Steel | 10,300 | 25,000 | 2,400 | Required | -40° to 245° | Lubrication Hole | 00000000 | 000000 |
Mounted Ball Bearings
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Bearings with nickel-plated cast iron housing are more corrosion resistant and durable than bearings with a cast iron housing.
Bearings with a set screw secure to shafts without using a collar. They let shafts rotate in both directions, so they’re good for applications where you need to reverse. However, the set screw will leave some marring on the shaft.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Nickel-Plated Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
1 11/16" | 2 1/8" | 4 3/16" | 7 15/32" | 2 1/4" | 13/16" | 21/32" | 5 3/4" | 7,650 | 4,750 | 3,000 | 0° to 210° | Self Aligning | Lubricated | 0000000 | 000000 |
Washdown Mounted Ball Bearings
Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants. All have NSF registered H1 lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications. Made of 316 stainless steel, they resist corrosion and prevent rusting caused by salt water, chlorine solutions, and chemicals.
Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw does leave some marring on shafts.
Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, won’t absorb water, and are FDA compliant.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Dp. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Lubrication | Specifications Met | Each | |
Self Aligning | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
1 11/16" | 2 1/8" | 4 1/4" | 7 1/2" | 4 1/4" | 0.688" | 5 3/4" | 7,900 | 5,100 | 1,500 | -20° to 220° | Lubricated | NSF Registered H1 | 0000000 | 0000000 |


For Shaft Diameter | OD | Material | Mount Type | Temperature Range,°F | Specifications Met | Each | |
Closed | |||||||
---|---|---|---|---|---|---|---|
1 11/16", 1 3/4", 45mm | 3 9/16", 90mm | Polypropylene Plastic | Snap In | -20° to 220° | FDA Compliant 21 CFR 177.1520 | 0000000 | 000000 |
Open | |||||||
1 11/16" | 3 9/16" | Polypropylene Plastic | Snap In | -20° to 220° | FDA Compliant 21 CFR 177.1520 | 0000000 | 00000 |
Mounted Ball Bearings with Two-Bolt Flange

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Bearings with a set-screw shaft mount secure to shafts with no need for an additional collar. They can be used for bi-directional shaft rotation when applications require reversing action. The set screw may cause some marring on the shaft.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
1 11/16" | 4 3/8" | 7 1/16" | 2 3/16" | 9/16" | 9/16" | 5 53/64" | 7,450 | 4,850 | 4,300 | -20° to 210° | Self Aligning | Lubricated | 00000000 | 0000000 |
Washdown Mounted Ball Bearings with Two-Bolt Flange
Used in food, beverage, pharmaceutical, and chemical plants, these mounted ball bearings are IP69K certified for washdown environments and have a two-bolt flange for mounting. Their 316 stainless steel housing has excellent corrosion resistance and prevents rust caused by salt water, chlorine solutions, and chemicals. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.
Set screw bearings grip shafts as you tighten their screw. They don’t use a collar, but the screw leaves some marring on shafts.
Snap optional covers onto bearings to protect them from moisture. Made of polypropylene, they resist corrosion, don’t absorb water, and are FDA compliant.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dp. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Specifications Met | Each | |
Sealed Steel Bearings with 316 Stainless Steel Housing | ||||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||||
1 11/16" | 2 3/16" | 4 3/8" | 7 1/16" | 3 3/64" | 1 9/16" | 1.563" | 5 27/32" | 7,900 | 5,100 | 1,500 | -20° to 220° | Self Aligning | Lubricated | NSF Registered H1 | 0000000 | 0000000 |


For Shaft Diameter | OD | Material | Mount Type | Temperature Range,°F | Specifications Met | Each | |
Closed | |||||||
---|---|---|---|---|---|---|---|
1 11/16", 1 3/4", 45mm | 3 9/16", 90mm | Polypropylene Plastic | Snap In | -20° to 220° | FDA Compliant 21 CFR 177.1520 | 0000000 | 000000 |
Open | |||||||
1 11/16" | 3 9/16" | Polypropylene Plastic | Snap In | -20° to 220° | FDA Compliant 21 CFR 177.1520 | 0000000 | 00000 |
Mounted Ball Bearings with Four-Bolt Flange
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
1 11/16" | 5 3/8" | 5 3/8" | 2 7/32" | 3/4" | 1/2" | 4 1/8" | 7,450 | 4,850 | 4,300 | -20° to 210° | Self Aligning | Lubricated | 00000000 | 0000000 |
Washdown Mounted Ball Bearings with Four-Bolt Flange
Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants. They have excellent corrosion resistance and prevent rusting caused by salt water, chlorine solutions, and chemicals because their housing is 316 stainless steel. All have USDA H1 approved lubrication, which is certified for incidental contact with food and is suitable for food and beverage applications.
Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw does leave some marring on shafts.
Snap optional covers onto bearings to shield them from moisture. Made of polypropylene, they resist corrosion, won’t absorb water, and are FDA compliant.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Specifications Met | Each | |
Sealed Steel Bearings with 316 Stainless Steel Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
1 11/16" | 5 3/8" | 5 3/8" | 2 3/64" | 9/16" | 19/32" | 4 1/8" | 7,900 | 5,100 | 1,500 | -20° to 220° | Self Aligning | Lubricated | NSF Registered H1 | 00000000 | 0000000 |


For Shaft Diameter | OD | Material | Mount Type | Temperature Range,°F | Specifications Met | Each | |
Closed | |||||||
---|---|---|---|---|---|---|---|
1 11/16", 1 3/4", 45mm | 3 9/16", 90mm | Polypropylene Plastic | Snap In | -20° to 220° | FDA Compliant 21 CFR 177.1520 | 0000000 | 000000 |
Open | |||||||
1 11/16" | 3 9/16" | Polypropylene Plastic | Snap In | -20° to 220° | FDA Compliant 21 CFR 177.1520 | 0000000 | 00000 |
Mounted Bearings with Three-Bolt Flange
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Steel bearings are stronger than stainless steel bearings, but not as corrosion resistant.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. Lg. | Hole Ctr.-to-Ctr. Ht. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Each | |
Sealed Steel Ball Bearings with Nickel-Plated Cast Iron Housing—Self Aligning | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
1 11/16" | 4 1/4" | 6 27/32" | 4 3/16" | 1 31/32" | 23/32" | 7/16" | 2 1/8" | 1 11/16" | 7,650 | 4,750 | 3,000 | 0° to 210° | 0000000 | 000000 |
Insert Bearings


Swap out worn inserts instead of replacing the entire mounted unit. Use the manufacturer model number on your existing mounted bearing to choose a compatible insert. Inserts must be used with the manufacturer model number specified.
For technical drawings and 3-D models, click on a part number.
For Shaft Dia. | For Mounted Bearing Model No. | Each | |
Sealmaster Steel Insert Bearings | |||
---|---|---|---|
Shaft Mount Type: Set Screw | |||
1 11/16" | NP-27, NPG-27-12, NPG-27-18, NPL-27, SC-27, SF-27, SFC-27, SFT-27, SP-27, ST-27, STH-27-12, STH-27-18, TB-27 | 00000000 | 0000000 |
Press-Fit Drill Bushings

Mount flush with jig plates for precise drilling. These bushings can also be used as spacers, shims, and machinery bushings.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Tolerance | Each | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
1.6875" ID | ||||||||||||
2 1/4" | 1" | 1 11/16" | 0.0003" to 0.0007" | 0.0021" to 0.0025" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 000000 | 000000 | 000000 |
Bearing Adapter Sleeves

Make up for imperfections and gaps between your bearing and shaft for a tight fit. These bearing adapter sleeves are the most common way to mount a bearing with a tapered bore onto a cylindrical seat. They work with both straight and stepped shafts. Secure using the included lock nut.
For technical drawings and 3-D models, click on a part number.
Adapter Sleeve Trade Number | For Shaft Diameter | ID | Width | Includes | Each | |
Low-Carbon Steel | ||||||
---|---|---|---|---|---|---|
SNW-10 | 1 11/16" | 1 11/16" | 1.755" | Lock Nut, Lock Washer | 0000000 | 000000 |
Quick-Disconnect (QD) Bushings


The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | ||||||||
---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Overall Wd. | Wd. | Dp. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
Clamp On | ||||||||
SD Style Bushing | ||||||||
1 11/16" | 1 13/16" | 3/8" | 3/16" | 108 | Steel | Clamping Screws | 00000000 | 000000 |
SDS Style Bushing | ||||||||
1 11/16" | 1 3/8" | 3/8" | 3/16" | 108 | Steel | Clamping Screws | 00000000 | 00000 |
SF Style Bushing | ||||||||
1 11/16" | 2 1/16" | 3/8" | 3/16" | 360 | Steel | Clamping Screws | 00000000 | 00000 |
SH Style Bushing | ||||||||
1 11/16" | 1 5/16" | __ | __ | 108 | Steel | Clamping Screws | 00000000 | 00000 |
SK Style Bushing | ||||||||
1 11/16" | 1 15/16" | 3/8" | 3/16" | 180 | Steel | Clamping Screws | 00000000 | 00000 |
Taper-Lock Bushings

Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing style. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | |||||||||
---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Overall Wd. | Wd. | Dp. | Taper | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
1610 Style Bushing | |||||||||
1 11/16" | 1" | 3/8" | 1/8" | 8° | 175 | Steel | Machine Key, Set Screws | 000000000 | 000000 |
2012 Style Bushing | |||||||||
1 11/16" | 1 1/4" | 3/8" | 3/16" | 8° | 280 | Steel | Set Screws | 000000000 | 00000 |
2517 Style Bushing | |||||||||
1 11/16" | 1 3/4" | 3/8" | 3/16" | 8° | 430 | Steel | Set Screws | 000000000 | 00000 |