System of Measurement System of Measurement |
---|
|
For Shaft Diameter For Shaft Diameter |
---|
|
Mounted Bearing Type Mounted Bearing Type |
---|
![]() | Base Mount |
![]() | Two-Bolt Flange Mount |
![]() | Four-Bolt Flange Mount |
Shaft Mount Type Shaft Mount Type |
---|
|
ID ID | Show |
---|
|
ID ID | Hide |
---|
Bearing Type Bearing Type |
---|
![]() | Ball |
For Load Direction For Load Direction |
---|
![]() | Radial |
Seal Type Seal Type |
---|
|
Bearing Material Bearing Material |
---|
|
Housing Material Housing Material |
---|
|
Mounting Hole Width Mounting Hole Width |
---|
|
Alignment Style Alignment Style |
---|
|
Lubrication Lubrication |
---|
|
Grease Fitting Included Grease Fitting Included |
---|
|
For Shaft Type For Shaft Type |
---|
![]() | Round |
Number of Set Screws Included Number of SetScrews Included |
---|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
---|
|
About Ball and Roller Bearings
More
Mounted Ball Bearings
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Bearings with a set screw secure to shafts without using a collar. They let shafts rotate in both directions, so they’re good for applications where you need to reverse. However, the set screw will leave some marring on the shaft.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
1 1/8" | 1 11/16" | 3 3/4" | 6 1/2" | 1 7/8" | 13/16" | 1/2" | 4 3/4" | 4,350 | 2,550 | 5,400 | -20° to 220° | Self Aligning | Lubricated | 0000000 | 0000000 |
Mounted Ball Bearings with Two-Bolt Flange

Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Bearings with a set-screw shaft mount secure to shafts with no need for an additional collar. They can be used for bi-directional shaft rotation when applications require reversing action. The set screw may cause some marring on the shaft.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
1 1/8" | 3 1/8" | 5 9/16" | 1 45/64" | 17/32" | 1/2" | 4 19/32" | 4,350 | 2,500 | 6,300 | -20° to 210° | Self Aligning | Lubricated | 0000000 | 0000000 |
Mounted Ball Bearings with Four-Bolt Flange
Bearings are self-aligning to compensate for shaft misalignment. Seals block out dust and contaminants.
Set screw bearings secure to shafts as you tighten their screw. They don’t need a collar, but the screw leaves some marring on shafts. Use them in applications where shafts rotate in both directions.
For technical drawings and 3-D models, click on a part number.

Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | ||||||||||||||
Shaft Mount Type: Set Screw | ||||||||||||||
1 1/8" | 4 1/4" | 4 1/4" | 1 45/64" | 5/8" | 1/2" | 3 1/4" | 4,350 | 2,500 | 6,300 | -20° to 210° | Self Aligning | Lubricated | 00000000 | 0000000 |
Insert Bearings


Swap out worn inserts instead of replacing the entire mounted unit. Use the manufacturer model number on your existing mounted bearing to choose a compatible insert. Inserts must be used with the manufacturer model number specified.
For technical drawings and 3-D models, click on a part number.
For Shaft Dia. | For Mounted Bearing Model No. | Each | |
SKF Steel Insert Bearings | |||
---|---|---|---|
Shaft Mount Type: Set Screw | |||
1 1/8" | F2B 102 TF, F4B 102-TF, FY 1.1/8 TF, FYT 1.1/8 TF | 0000000 | 000000 |