We will reply to your message within an hour.
Wider than our standard ball bearings, these rugged bearings are good for handling heavy loads at low speeds.
Slip these bearings onto a shaft and secure with the included set screws, no special tools required.
Secure these bearings in washdown areas, such as food, beverage, pharmaceutical, and chemical plants, by tightening the set screw onto a shaft—no additional collar needed.
In addition to handling higher loads than three-piece ball bearings, one-piece bearings are easier to handle. They have an outer band that holds the bearing together and acts as a shield against dust and other contaminants.
Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.
Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together.
Adapt high-precision needle-roller bearings to use on unhardened, unground shafts.
Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
These bronze bearings are strong, wear resistant, and excellent at handling shock loads.
A figure-8-shaped groove provides a flow path for lubricant, distributing it evenly along the bearing’s surface.
Grooves on the inside of the bearing provide a flow path for lubricant, distributing it evenly along the bearing’s surface.
The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.
Also known as Oilite® bearings.
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.
Handle heavy loads that frequently start and stop along shafts—these bearings contain extra iron and slippery PTFE lubricant. They’re thrust bearings, which means they support loads parallel to the shaft.
Made of 863 iron-copper and embedded with NSF registered H1 oil, these bearings can tackle high-load applications in food plants, such as bottling and filling lines.
Use where high loads and speeds are not required.
A metal backing adds strength.
Ball bearings operate with less friction than other bearings, so they can run at higher speeds.
A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication.
Also known as tapped-base bearings, these ball bearings mount to surfaces from the bottom through threaded holes. Because of their narrow profile, they’re commonly used in tight-clearance spaces, including systems where multiple shafts are mounted close together.
These bearings have the highest speed ratings of any mounted ball bearing that we offer.
Meeting IP69K for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants.
Synthetic grease or graphite enables these bearings to operate in high temperatures.
Keep shafts, such as those with a shoulder, clear of the mounting surface. These bearings have a higher mounting base that gives them more space to the mounting surface than standard mounting bases.
A reliable classic—these babbitt bearings are strong and corrosion resistant.
Roller bearings have a thinner profile and larger contact area than ball bearings, making them stronger and more space-efficient than ball bearings.
Ball bearings operate with less friction than other bearings, so you can run them at higher speeds.
An elongated mounting hole on one side of the flange lets you adjust the position of these bearings without having to remove your shaft.
A bolt in each corner makes for a secure, even hold.
The tapered rollers in these bearings support large shafts at high static loads.
With all three mounting holes on one side, you can position the bearing above or below the mounting surface.
Swap out worn inserts instead of replacing the entire mounted unit.
Also known as spherical bearings, swivel joints support angular misalignment. Press them into a hole or housing where a ball joint rod end won’t fit.
Specially designed lubrication channels and integral seals allow these joints to last up to three times longer than other swivel joints.
A unique design allows these joints to support heavy one-direction thrust loads as well as combined radial/thrust loads.
Offering excellent antifriction qualities, 932 bronze also offers good strength and wear resistance. It's also known as SAE 660 and is often used for bearings, bushings, and thrust washers.
Powdered bronze is pressed and then impregnated with SAE 30 oil to make this material self-lubricating.
954 bronze contains a minimum of 10% aluminum for strength and weldability. It is also known as aluminum bronze. It's widely used for bearings, bushings, valve bodies, and worm gears. The strength of this material increases with heat treating.
An easier-to-machine alternative to 932 bronze, 936 also has better corrosion resistance. It's also called modified SAE 64.
The addition of MDS gives these tubes exceptional wear resistance along with a self-lubricating surface. They're made of cast nylon 6, making them easier to machine and better electrical insulators than other MDS-filled nylon tubes.
A good choice for making sprockets and pulleys, these cast nylon 6 tubes withstand higher temperatures and are easier to machine than standard nylon 6/6 tubes.
Delrin® acetal resin, also known as acetal homopolymer, is stronger and stiffer than acetal copolymer.
In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.
Precisely align, level, and adjust spacing on fasteners and shafts with these shims.
Be prepared with ring shims in a variety of thicknesses. These shims fit around fasteners and shafts to precisely align, level, and adjust spacing.
Also known as machinery bushings, these shims have an oversized OD to create a larger bearing surface for reduced wear between moving parts.
Precisely align, level, and adjust spacing on fasteners, shafts, and machinery with these shims, which are color-coded by thickness for easy identification.
Be prepared with ring shims in a variety of thicknesses. These shims are color-coded by thickness for easy identification.
Be prepared with shims in a variety of thicknesses. Also known as arbor spacers, these shims are notched to fit over keyed shafts.
Insert these bushings into the bore of your sprocket for flush or recessed mounting.
A toothed slot lets these bushings contract for insertion into the bore of your sprocket or pulley and then expand for a snug fit.
The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings.
Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws.