About Copper, Brass, and Bronze
More
About Plain Bearings
More
About Ball and Roller Bearings
More
About Plastic
More
Set Screw Collar Ball Bearings
Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.
Bearings with a black-oxide steel ring have some corrosion resistance.
Sealed bearings block out dust and other contaminants better than shielded bearings.
Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.
Flanged bearings have a flange that ensures proper positioning inside a tube or housing.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number  | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | ABEC Rating | Each | |
Sealed (Lubricated) | ||||||||||||||
Black-Oxide Steel—With Retaining Ring | ||||||||||||||
| ER26 | 1 5/8" | 3.347" | 1 3/32" | 2.2969" | 1.9375" | 3 19/32" | 0.0625" | 7,900 | 5,100 | 3,800 | -20° to 220° | ABEC-1 | 0000000 | 0000000 |
Steel—Flanged | ||||||||||||||
| GYA110RRB | 1 5/8" | 3.3465" | 0.866" | 2.2813" | 1.6555" | __ | __ | 8,150 | 4,500 | 4,200 | -65° to 250° | ABEC-1 | 0000000 | 000000 |
One-Piece Thrust Ball Bearings
In addition to handling higher loads than three-piece ball bearings, one-piece bearings are easier to handle. They have an outer band that holds the bearing together and acts as a shield against dust and other contaminants.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Features | Each | |
Shielded | |||||||||||
| 1 5/8" | 2 31/32" | 13/16" | Steel | 10,300 | 25,000 | 2,400 | Required | -40° to 250° | Lubrication Hole | 00000000 | 000000 |
Oil-Embedded Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 1 5/8" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 2" | 1 1/2" | 4,850 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
| 2" | 2" | 6,500 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
| 2" | 3" | 9,750 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 00000 |
Oil-Embedded Flanged Sleeve Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
841 Bearing Bronze Bearings | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
For 1 5/8" Shaft Dia. | ||||||||||
| 2" | 2" | 2 1/4" | 3/16" | 6,500 lbs. @ 30 rpm | 3,800 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
Multipurpose Flanged Sleeve Bearings
These bronze bearings are strong, wear resistant, and excellent at handling shock loads. They’re sometimes called 660 leaded bronze bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Temperature Range, °F | Each | |
932 Bearing Bronze Bearings | |||||||||
|---|---|---|---|---|---|---|---|---|---|
For 1 5/8" Shaft Dia. | |||||||||
| 2" | 2" | 2 1/4" | 3/16" | 13,000 lbs. @ 30 rpm | 7,600 lbs. @ 30 rpm | Required | -350° to 450° | 00000000 | 000000 |
High-Load Dry-Running Thrust Bearings
A steel backing adds strength to these slippery PTFE bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD | Thick. | Dynamic Thrust Load Capacity | Temperature Range, °F | Each | |
Steel-Backed PTFE Plastic Bearings | |||||
|---|---|---|---|---|---|
For 1 5/8" Shaft Dia. | |||||
| 2 5/8" | 1/16" | 16,500 lbs. @ 30 rpm | -320° to 530° F° | 0000000 | 00000 |
Needle-Roller Bearings
Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.
Open bearings dissipate heat more efficiently than sealed bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range, °F | Specifications Met | Each | |
Open | ||||||||||||
| 1 5/8" | 2" | 5/8" | Steel | 5,700 | 8,900 | 6,200 | Required | 8 | -40° to 280° | __ | 00000000 | 000000 |
| 1 5/8" | 2" | 1 1/4" | Steel | 11,400 | 21,800 | 6,000 | Required | 8 | -20° to 280° | DIN 281, ISO 76 | 00000000 | 00000 |
Tapered-Roller Thrust Bearings
Thick, tapered rollers stand up to extremely high thrust loads.
Open bearings dissipate heat more efficiently than sealed bearings.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Each | |
Open | ||||||||||
| 1 5/8" | 2.869" | 0.8438" | Steel | 20,500 | 62,500 | 10 | Required | 0° to 150° | 00000000 | 000000 |
Mounted Roller Bearings
Roller bearings have a thinner profile and larger contact area than ball bearings, making them stronger and more space-efficient than ball bearings.
Sealed bearings block out dust and contaminants.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Hole Lg. | Hole Wd. | Hole Ctr.-to-Ctr. | Dynamic | Static | Dynamic Thrust Load Cap., lbs. | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Steel Bearings with Cast Iron Housing—Shaft Mount Type: Set Screw | ||||||||||||||||
| 1 5/8" | 2 1/8" | 4 1/4" | 7 7/8" | 3 3/8" | 3/4" | 5/8" | 6 1/4" | 7,850 | 33,000 | 2,550 | 3,300 | -60° to 250° | Fixed Alignment | Lubricated | 0000000 | 0000000 |
932 Bearing Bronze Tubes
- Yield Strength: 18,000 psi
- Hardness: Rockwell B35 (Soft)
- Temper: M07
- Heat Treatable: No
- Specifications Met: ASTM B505
Offering excellent antifriction qualities, 932 bronze also offers good strength and wear resistance. It's also known as SAE 660 and is often used for bearings, bushings, and thrust washers.
For technical drawings and 3-D models, click on a part number.
Certificates with a traceable lot number are available for these products. Download certificates from ORDER HISTORY after your order ships.
Press-Fit Drill Bushings
Mount flush with jig plates for precise drilling. These bushings can also be used as spacers, shims, and machinery bushings.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
1.625" ID | ||||||||||||
| 2 1/4" | 1" | 1 5/8" | 0.0003" to 0.0007" | 0.0021" to 0.0025" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 000000 | 000000 | 000000 |
| 2 1/4" | 1 1/2" | 1 5/8" | 0.0003" to 0.0007" | 0.0021" to 0.0025" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Press-Fit Drill Bushings with Head
The head prevents these bushings from being pushed through the jig when drilling pressure is extreme. The head sits above the jig plate or can be mounted flush by installing in a counterbored hole. Drill bushings can also be used as spacers, shims, and machinery bushings.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
1.625" ID | ||||||||||||||
| 2 1/4" | 1 3/8" | 1 5/8" | 2 31/64" | 3/8" | 0.0003" to 0.0007" | 0.0021" to 0.0025" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 000000 | 000000 | 000000 |
Quick-Disconnect (QD) Bushings
The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | ||||||||
|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
Clamp On | ||||||||
SD Style Bushing | ||||||||
| 1 5/8" | 2 3/32" | 3/8" | 3/16" | 108 | Steel | Clamping Screws | 00000000 | 000000 |
SDS Style Bushing | ||||||||
| 1 5/8" | 1 21/32" | 3/8" | 3/16" | 108 | Steel | Clamping Screws | 00000000 | 00000 |
SF Style Bushing | ||||||||
| 1 5/8" | 2 1/2" | 3/8" | 3/16" | 360 | Steel | Clamping Screws | 00000000 | 00000 |
SH Style Bushing | ||||||||
| 1 5/8" | 1 19/32" | 3/8" | 1/16" | 108 | Steel | Clamping Screws, Machine Key | 00000000 | 00000 |
SK Style Bushing | ||||||||
| 1 5/8" | 2 9/32" | 3/8" | 3/16" | 180 | Steel | Clamping Screws | 00000000 | 00000 |
Split-Tapered Bushings
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They're for use with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
Bushings with a machine key fit into a matching keyway on a sprocket or pulley for high-torque applications.
For technical drawings and 3-D models, click on a part number.
Keyway | |||||||
|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Taper | Fastener Tightening Torque, in.-lbs. | Each | |
Steel | |||||||
P1 Style Bushing with Machine Key | |||||||
| 1 5/8" | 1 15/16" | 3/8" | 5/16" | 3° | 192 | 00000000 | 000000 |
P2 Style Bushing with Machine Key | |||||||
| 1 5/8" | 2 15/16" | 3/8" | 5/16" | 3° | 192 | 00000000 | 00000 |
Q1 Style Bushing with Machine Key | |||||||
| 1 5/8" | 2 1/2" | 3/8" | 3/16" | 3° | 348 | 00000000 | 00000 |
Taper-Lock Bushings
Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing style. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Taper | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
1610 Style Bushing | |||||||||
| 1 5/8" | 1" | 3/8" | 1/8" | 8° | 175 | Steel | Machine Key, Set Screws | 000000000 | 000000 |
1615 Style Bushing | |||||||||
| 1 5/8" | 1 1/2" | 3/8" | 1/8" | 8° | 175 | Steel | Machine Key, Set Screws | 000000000 | 00000 |
2012 Style Bushing | |||||||||
| 1 5/8" | 1 1/4" | 3/8" | 3/16" | 8° | 280 | Steel | Set Screws | 000000000 | 00000 |
2517 Style Bushing | |||||||||
| 1 5/8" | 1 3/4" | 3/8" | 3/16" | 8° | 430 | Steel | Set Screws | 000000000 | 00000 |
3020 Style Bushing | |||||||||
| 1 5/8" | 2" | 3/8" | 3/16" | 8° | 800 | Steel | Set Screws | 000000000 | 00000 |
Wide-Rim Ring Shims
Also known as machinery bushings, these shims have an oversized OD to create a larger bearing surface for reduced wear between moving parts. Use them to precisely align, level, and adjust spacing on shafts and machinery.
Carbon steel shims have excellent strength and can be welded.
A zinc-plated finish adds a layer of corrosion resistance.
For technical drawings and 3-D models, click on a part number.
| ID | ID Tolerance | OD | OD Tolerance | Material | Min. Hardness | Magnetic Properties | Pkg. Qty. | Pkg. | |
0.075" Thick. (-0.007" to 0.007" Tolerance) | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 1 5/8" | 0.01" to 0.025" | 2 3/8" | -0.01" to 0.01" | 1008-1010 Carbon Steel | Rockwell B38 | Magnetic | 10 | 000000000 | 00000 |
0.134" Thick. (-0.008" to 0.008" Tolerance) | |||||||||
| 1 5/8" | 0.01" to 0.025" | 2 3/8" | -0.01" to 0.01" | 1008-1010 Carbon Steel | Rockwell B38 | Magnetic | 10 | 000000000 | 00000 |
| ID | ID Tolerance | OD | OD Tolerance | Material | Min. Hardness | Magnetic Properties | Pkg. Qty. | Pkg. | |
0.075" Thick. (-0.007" to 0.007" Tolerance) | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 1 5/8" | 0.01" to 0.025" | 2 3/8" | -0.01" to 0.01" | Zinc-Plated 1008-1010 Carbon Steel | Rockwell B38 | Magnetic | 10 | 000000000 | 00000 |
0.134" Thick. (-0.008" to 0.008" Tolerance) | |||||||||
| 1 5/8" | 0.01" to 0.025" | 2 3/8" | -0.01" to 0.01" | Zinc-Plated 1008-1010 Carbon Steel | Rockwell B38 | Magnetic | 5 | 000000000 | 0000 |
Clear Impact-Resistant Polycarbonate Tubes
- Color: Clear
- Temperature Range: -40° to 200° F
- Tensile Strength: 8,900-9,500 psi (Good)
- Impact Strength: 12-18 ft.-lbs./in. (Excellent)
- Hardness: Rockwell R118 (Hard)
- For Use Outdoors: No
Comparable to Lexan, Hyzod, Tuffak, and Makrolon, these polycarbonate tubes are half the weight of glass and maintain excellent impact resistance across a wide temperature range. Use them to make instrument gauge covers and display racks.
For technical drawings and 3-D models, click on a part number.
