11mm ID Bearings | McMaster-Carr

Filter by

System of Measurement

Shaft Diameter

Length

Shaft Motion

Shaft Mount Type

Plain Bearing Type

Bearing Type

Diameter

Overall Length

Number of Splines

Dynamic Load Capacity

Material

Travel Distance per Turn

For Housing ID

Lubrication

Flange OD

Shaft Type

Minimum Temperature

RoHS Compliance

Root Diameter

Static Load Capacity

Forward

How can we improve?

13 Products

About Plain Bearings

Use where high loads and speeds are not required.

Thermoplastic-blend bearings have low moisture absorption and create very low friction in applications with light loads, and frequent starts and stops.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Thermoplastic-Blend Bearings
For Housing ID	Lg.	Flange OD	Flange Thick.	Dynamic Radial Load Capacity	Dynamic Thrust Load Capacity	Color	Temperature Range, °F		Each
For 11mm Shaft Dia.
13mm	5mm	18mm	1mm	60 lbs. @ 120 rpm	105 lbs. @ 120 rpm	Yellow	-50° to 190°	00000000	00000

Light Duty Dry-Running Thrust Bearings

Use where high loads and speeds are not required.

Thermoplastic bearings are fiber reinforced and lubricant infused for good wear resistance and low friction with light and medium loads.

Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.

For technical drawings and 3-D models, click on a part number.

Thermoplastic Blend Bearings
OD	Thick.	Dynamic Thrust Load Capacity	Color	Temp. Range, °F		Each
For 11 mm Shaft Dia.
15mm	1mm	13 lbs. @ 120 rpm	Gray	-40° to 260°	0000000	00000
27mm	0.5mm	75 lbs. @ 120 rpm	Gray	-40° to 260°	0000000	0000

Metric Press-Fit Drill Bushings

Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.

All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. They also have internal chamfers, so it's easier to insert bits, pins, and punches into the bushing. Some bushings have internal chamfers on both ends, so no matter which end of the bushing is inserted into your jig, your bits, pins, and other tooling enter easily. Having an internal chamfer on the bottom of your bushing may cause shavings to get caught and bind as you remove the bit, however.

DIN 179 bushings meet dimensional and material standards that make sure they're compatible with other parts and tools. Although DIN 179 is no longer an active standard, it's still a common reference point for designers.

Don't see the size you need? Additional sizes are available.

For technical drawings and 3-D models, click on a part number.

				Tolerance								Each
OD, mm	Lg., mm	Internal Chamfer	For Drill Bit Size	ID, mm	OD, mm	Lg., mm	Drill Bushing Type	Material	Hardness	Specifications Met		1-5	6-11	12-Up
11 mm ID
18	12	Both Ends	11 mm	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	__	000000000	000000	000000	00000
18	12	One End	11 mm	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	000000000	00000	00000	0000
18	20	Both Ends	11 mm	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	__	000000000	00000	00000	00000
18	20	One End	11 mm	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	000000000	00000	00000	00000
18	25	Both Ends	11 mm	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	__	000000000	00000	00000	00000
18	25	One End	11 mm	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	PM	Steel	Rockwell C61	DIN 179	000000000	00000	00000	00000

Metric Press-Fit Drill Bushings with Head

Shown in Countersunk Hole

Shown in Standard Hole

Even under extreme drilling pressure, these metric bushings won't press through your jig plate. A flanged head on the top of the bushing acts as a stop, preventing it from moving as you push down your drill bit, reamer, or other cutting bit. Drill bushings ensure accurate, consistent cuts and drilled holes from one part to the next. They sometimes also work as spacers, shims, and machinery bushings. Made of hardened, ground steel, these bushings hold their shape and resist wear over time. The flanged head protects your jig plate from damage caused by heavy use.

Although it's no longer an active standard, DIN 172 is still a common reference point for making sure parts are compatible with other parts and tools.

These bushings work in both countersunk and standard drill holes. To install, place the bushing inside the hole in your jig. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once centered, press the bushing into the hole with a hydraulic or lever press.

For technical drawings and 3-D models, click on a part number.

		Head		Tolerance								Each
OD, mm	Lg., mm	OD, mm	Thick., mm	ID, mm	OD, mm	Lg., mm	Drill Bushing Type	Material	Hardness	Specifications Met		1-5	6-11	12-Up
11 mm ID
18	8	22	4	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	000000000	000000	000000	000000
18	16	22	4	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000
18	21	22	4	0.016 to 0.034	0.012 to 0.023	-0.2 to 0.2	H	Steel	Rockwell C61	DIN 172	000000000	00000	00000	00000

Ball Screw/Splines and Bearings

From one compact system, transmit linear or rotary motion or both at once (sometimes called spiral motion). Because of these different motions, these ball screw/splines and bearings create efficient, fluid movements in complex automated applications, such as pick-and-place robots.

The ball bearings move smoothly and precisely, even at high speeds. They're powered independently, so you can drive one bearing at a time or both together to coordinate movements.

The ball screw/splines are hardened on the surface, so they stand up to repeated motion. They’re also hollow, so you can run electrical wiring, compressed air tubing, coolants, or lubricant through their center.

For technical drawings and 3-D models, click on a part number.

Spline		Thread					Ball Screw Bearing				Ball Spline Bearing
Lg.	No. of	Lg.	Direction	ID, mm	Lg., mm	Root Dia., mm	OD, mm	Overall Lg., mm	Dynamic Load Cap., lbs.	Static Load Cap., lbs.	OD, mm	Overall Lg., mm	Dynamic Load Cap., lbs.	Static Load Cap., lbs.	Max. Dynamic Torque, in.-lbs.	Temp. Range, ° F		Each
Metric—1055 Carbon Steel
16mm Dia. (Tolerance: -0.018mm to 0mm)
500 mm	6	360 mm	Right Hand	11	500	15.15	32	40	870	1,610	31	50	1,590	2,830	277	5° to 176°	0000000	000000000

Email Us

About Plain Bearings

Light Duty Dry-Running Flanged Sleeve Bearings

Light Duty Dry-Running Thrust Bearings

Metric Press-Fit Drill Bushings

Metric Press-Fit Drill Bushings with Head

Ball Screw/Splines and Bearings