About Ball and Roller Bearings
More
About Plain Bearings
More
Set Screw Collar Ball Bearings
Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.
Sealed bearings block out dust and other contaminants better than shielded bearings.
Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number  | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | ABEC Rating | Each | |
Sealed (Lubricated) | ||||||||||||||
Steel—With Retaining Ring | ||||||||||||||
| 7613-2RS | 13/16" | 2" | 5/8" | 1.306" | 1.179" | 2.156" | 0.042" | 2,950 | 1,350 | 5,000 | -20° to 250° | Not Rated | 0000000 | 000000 |
One-Piece Thrust Ball Bearings
In addition to handling higher loads than three-piece ball bearings, one-piece bearings are easier to handle. They have an outer band that holds the bearing together and acts as a shield against dust and other contaminants.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Features | Each | |
Shielded | |||||||||||
| 13/16" | 1 15/32" | 9/16" | Steel | 4,250 | 7,300 | 5,500 | Required | -40° to 245° | Lubrication Hole | 00000000 | 000000 |
Oil-Embedded Thrust Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD | Thick. | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 13/16" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 1 1/2" | 1/8" | 2,600 lbs. @ 60 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
High-Load Ultra-Low-Friction Oil-Embedded Thrust Bearings
Handle heavy loads that frequently start and stop along shafts—these bearings contain extra iron and slippery PTFE lubricant. Startup friction causes a thin layer of PTFE to release onto the surface. Thanks to their high iron content, they also resist failing if their load suddenly and drastically increases, but they won’t run as fast as standard bearings. They’re thrust bearings, which means they support loads parallel to the shaft.
For technical drawings and 3-D models, click on a part number.
| OD | Thickness | Dynamic Thrust Load Capacity | Lubrication | Lubrication Method | Temp. Range, °F | Each | |
For 13/16" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 1 1/4" | 1/8" | 1,850 lbs. @ 60 rpm | Lubricated | Embedded | -60° to 300° | 00000000 | 000000 |
High-Load Dry-Running Thrust Bearings
A steel backing adds strength to these slippery PTFE bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD | Thick. | Dynamic Thrust Load Capacity | Temperature Range, °F | Each | |
Steel-Backed PTFE Plastic Bearings | |||||
|---|---|---|---|---|---|
For 13/16" Shaft Dia. | |||||
| 1 3/8" | 1/16" | 4,550 lbs. @ 60 rpm | -320° to 530° F° | 0000000 | 00000 |
Press-Fit Drill Bushings
Mount flush with jig plates for precise drilling. These bushings can also be used as spacers, shims, and machinery bushings.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.8125" ID | ||||||||||||
| 1 1/8" | 1/2" | 13/16" | 0.0002" to 0.0006" | 0.0017" to 0.002" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 000000 | 000000 | 000000 |
| 1 1/8" | 3/4" | 13/16" | 0.0002" to 0.0006" | 0.0017" to 0.002" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
| 1 1/8" | 1" | 13/16" | 0.0002" to 0.0006" | 0.0017" to 0.002" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
| 1 1/4" | 3/4" | 13/16" | 0.0002" to 0.0006" | 0.0017" to 0.002" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1 1/4" | 2" | 13/16" | 0.0002" to 0.0006" | 0.0017" to 0.002" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1 3/8" | 1/2" | 13/16" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
| 1 3/8" | 1" | 13/16" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
| 1 3/8" | 1 3/8" | 13/16" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
| 1 3/8" | 2" | 13/16" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
Press-Fit Drill Bushings with Head
The head prevents these bushings from being pushed through the jig when drilling pressure is extreme. The head sits above the jig plate or can be mounted flush by installing in a counterbored hole. Drill bushings can also be used as spacers, shims, and machinery bushings.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
0.8125" ID | ||||||||||||||
| 1 3/8" | 1" | 13/16" | 1 39/64" | 3/8" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 000000 | 000000 | 000000 |
Removable Drill Bushings
Replace worn bushings and quickly change IDs without needing to repeatedly use a lever press. Instead of pressing bushings in and out of your jig fixture, which can cause damage, these bushings slide in and out of sleeves (sold separately). By swapping in a bushing with a different ID, you can change the size of your bit and still use the same hole in your fixture. All are made to tight dimensional tolerances for consistent, accurate results, even as you change them in and out. They're also known as slip-fixed and renewable bushings.
Choose a sleeve with a length that matches the length of your bushing. To prevent bushings from spinning inside the sleeve as you drill, pair a standard sleeve with a lock screw, or use a locking sleeve.
Lock screws thread into a hole in your jig. The head of the screw fits into a notch on the bushing's head, which keeps the bushing from spinning.
For additional sizes, see Made-to-Order Removable Drill Bushings.
For technical drawings and 3-D models, click on a part number.
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | Lock Screw/Bushing Ctr.-to-Ctr. | ID | OD | Lg. | Drill Bushing Type | Material | 1-5 | 6-11 | 12-Up | |
0.8125" ID | ||||||||||||||
| 1" | 3/4" | 13/16" | 1 27/64" | 3/8" | 59/64" | 0.0002" to 0.0006" | -0.0002" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 000000 | 000000 | 000000 |
| 1 3/8" | 1" | 13/16" | 1 51/64" | 3/8" | 1 7/64" | 0.0002" to 0.0006" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
Taper-Lock Bushings
Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing style. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Taper | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
1610 Style Bushing | |||||||||
| 13/16" | 1" | 3/16" | 3/32" | 8° | 175 | Steel | Set Screws | 000000000 | 000000 |
Quick-Disconnect (QD) Bushings
The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | ||||||||
|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
Clamp On | ||||||||
JA Style Bushing | ||||||||
| 13/16" | 1" | 3/16" | 3/32" | 60 | Steel | Clamping Screws | 00000000 | 000000 |