13mm OD Bearings | McMaster-Carr

Smoother than smooth—the balls inside these bearings roll nearly friction-free. You’ll often find them on rapidly rotating parts, from the whirring chuck on a power drill to the spinning shaft on an electric motor.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

Corrosion-Resistant 440C Stainless Steel—Combine the strength of steel with the corrosion resistance of stainless steel. These bearings won't degrade from water or mild chemicals, such as the ammonia in cleaning solutions. However, they'll weaken when exposed to salt water and harsh chemicals, such as bleach.

Highly Corrosion-Resistant 316 Stainless Steel—The most corrosion-resistant metal bearings we offer. They won't pit or weaken from salt water or harsh chemicals, such as bleach and chlorine found in cleaning solutions.

ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Open







				Highly Corrosion-Resistant 316 Stainless Steel

				4	13	5	Not Rated	75	2,300	-40	140	Standard	624	5908K721	000000


				Shielded







								Steel

								4	13	5	3	210	53,000	-20	230	Standard	624-2Z	4481N32	00000




										Corrosion-Resistant 440C Stainless Steel

										4	13	5	5	290	48,000	-40	240	Standard	624-2Z	7804K103	0000


										5	13	4	5	240	50,000	-40	240	Standard	695-2Z	7804K108	0000
										6	13	5	5	240	48,000	-40	240	Standard	686-2Z	7804K113	0000


										Sealed







														Steel

														4	13	5	3	210	32,000	-30	210	Standard	624-2RS	4481N78	00000

Permanently Lubricated Ball Bearings

Install and forget these self-lubricating bearings. Their lubricant is a solid material that fills the space between the balls and releases oil over time, so you'll never need to add more.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Open







				Corrosion-Resistant 440C Stainless Steel

				3	13	5	1	220	37,000	-10	200	Standard	633	4668K104	000000


				5	13	4	1	180	33,000	-10	200	Standard	695	4668K115	00000
				6	13	3.5	1	180	31,000	-10	200	Standard	686	4668K119	00000


				Sealed







								Corrosion-Resistant 440C Stainless Steel

								3	13	5	1	220	37,000	-10	200	Standard	633-2RS	4668K215	00000


								4	13	5	1	220	35,000	-10	200	Standard	624-2RS	4668K222	00000
								5	13	4	1	180	33,000	-10	200	Standard	695-2RS	4668K226	00000
								6	13	5	1	180	31,000	-10	200	Standard	686-2RS	4668K231	00000

Flanged Ball Bearings

Install these bearings inside a housing and they won't budge. The flange presses against the housing wall, so vibration and other sudden forces parallel to the shaft (thrust loads) won't knock them off-kilter.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

				Flange, mm					Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	OD	Thk.	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Open







				Steel

				6	13	3.5	15	1	3	240	56,000	-50	300	Standard	686	57155K476	000000




						Corrosion-Resistant 440C Stainless Steel

						4	13	5	15	1	3	230	60,000	-50	300	Standard	624	57155K452	00000


						5	13	4	15	1	3	190	59,000	-50	300	Standard	695	57155K465	00000


						Shielded







										Steel

										5	13	4	15	1	3	240	50,000	-50	300	Standard	695-2Z	57155K575	00000


										6	13	5	15	1.1	3	240	48,000	-50	300	Standard	686-2Z	57155K588	00000




												Corrosion-Resistant 440C Stainless Steel

												4	13	5	15	1	3	240	51,000	-50	300	Standard	624-2Z	57155K563	00000


												5	13	4	15	1	3	190	50,000	-50	300	Standard	695-2Z	57155K576	00000
												5	13	4	15	1	5	240	50,000	-20	250	Standard	695-2Z	7804K138	0000
												6	13	5	15	1.1	3	190	48,000	-50	300	Standard	686-2Z	57155K589	00000
												6	13	5	15	1.1	5	240	48,000	-20	250	Standard	686-2Z	7804K143	0000

Ball Bearings for Food and Beverage

Sealed

Food production rolls along smoothly on these bearings. Greased with FDA-compliant lubricant, they’re safe to install on food-processing equipment, such as conveyor belts, so long as they don’t directly touch the food. The lubricant is a solid material that fills the space between the balls and releases oil over time, so you'll never need to add more.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Food Industry Std.	Bearing Trade No.		Each
Sealed







				Corrosion-Resistant 440C Stainless Steel

				4	13	5	1	290	35,000	-40	200	Standard	FDA Compliant 21 CFR 178.3570	624-2RS	4648K306	000000


				5	13	4	1	240	33,000	-40	200	Standard	FDA Compliant 21 CFR 178.3570	695-2RS	4648K318	00000
				6	13	5	1	240	31,500	-40	200	Standard	FDA Compliant 21 CFR 178.3570	686-2RS	4648K314	00000

High-Precision Ball Bearings

Open

Shielded

The most precise bearings we offer, with tolerances tighter than a speck of dust. Rated ABEC 7 out of 9, they meet strict tolerance standards established by the Annular Bearing Engineers Committee (ABEC). You'll find them in equipment that requires both high speed and pinpoint accuracy, such as gyroscopes.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type		Each
Open







				Corrosion-Resistant 440C Stainless Steel

				4	13	5	7	205	44,000	-30	280	Standard	7487N18	000000


				6	13	3.5	7	160	42,000	-30	280	Standard	7487N26	00000


				Shielded







								Corrosion-Resistant 440C Stainless Steel

								5	13	4	7	185	44,000	-30	280	Standard	7487N52	00000


								6	13	5	7	160	42,000	-30	280	Standard	7487N56	00000

Dry-Running Flanged Sleeve Bearings

Made of naturally slippery plastic so you’ll never have to add lubricant. They’re ideal for clean environments where you need to prevent oil drips or graphite flakes. Compared to metal bearings, they are lighter and will never rust.

Flanged sleeve bearings combine a sleeve and thrust bearing in one. The flange supports thrust loads and prevents the bearing from being pushed out of place. The sleeve is the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

Nylon—The most popular choice, nylon is wear resistant yet economical. Keep in mind, though, that it will swell and weaken when exposed to moisture.

Ultra-Chemical-Resistant PTFE—The most chemical-resistant bearings we offer. PTFE is unaffected by the harsh fluids that other plastics can't handle, including all strong acids and bases. PTFE also reduces friction better than nylon but is not as strong.

High-Load Moisture-Resistant Rulon LR—Won’t swell in wet or humid places, similar to acetal, but can support higher loads. These bearings also operate smoothly from cryogenic to oven-like temperatures.

Moisture-Resistant Ultra-Low-Friction Plastic Blend—These bearings won't warp or swell from humidity or direct contact with water. They glide effortlessly for applications with frequent starts and stops, such as conveyor systems.

	For Housing ID, mm	Lg., mm	Flange OD, mm	Flange Thk., mm	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Color	Temp. Range, ° F	Specs. Met		Each
Nylon



	10	13	10	16	1.5	37 lb. @ 120 rpm	28 lb. @ 120 rpm	White	-20 to 210	—	6389K485	00000


	10	13	20	16	1.5	75 lb. @ 120 rpm	28 lb. @ 120 rpm	White	-20 to 210	—	6389K481	0000


	Ultra-Chemical-Resistant PTFE



			10	13	12	16	1.5	15 lb. @ 120 rpm	9.5 lb. @ 120 rpm	White	-200 to 450	FDA Compliant 21 CFR 177.1550	2706T524	00000


			10	13	16	16	1.5	20 lb. @ 120 rpm	9.5 lb. @ 120 rpm	White	-200 to 450	FDA Compliant 21 CFR 177.1550	2706T525	00000


			High-Load Moisture-Resistant Rulon LR



					10	13	12	16	1.5	150 lb. @ 120 rpm	95 lb. @ 120 rpm	Maroon	-400 to 500	—	6362K424	00000


					Moisture-Resistant Ultra-Low-Friction Plastic Blend



							11	13	5	18	1	60 lb. @ 120 rpm	105 lb. @ 120 rpm	Yellow	-50 to 190	—	2705T141	0000

Needle-Roller Bearings

Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.

Open Bearing—Open bearings dissipate heat more efficiently than sealed bearings.

				Radial Load Cap., lb.
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	For Shaft Surface Smoothness, Ra, μin	Temp. Range, ° F	Specs. Met		Each
For Radial Load—Open with Steel Ring



		9	13	8	750	800	26,500	Required	8	-20 to 280	DIN 618, ISO 3245	5905K526	00000


		9	13	10	960	1,050	26,500	Required	8	-40 to 280	DIN 618, ISO 3245	5905K353	0000
		9	13	12	1,150	1,400	26,500	Required	8	-20 to 280	DIN 618, ISO 3245	5905K527	0000

Dry-Running Ball Bearings

Made of naturally slippery plastic so there's no lubricant to maintain or make a mess. These bearings are ideal for spic-and-span spaces since oil won't drip off, wash out, or collect dust over time. They won't rust or warp from moisture, so they stand up to thorough cleanings.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, reducing wear and extending the life of the bearing.

Acetal—The most common choice for plastic bearings, acetal is economical yet still stands up to daily wear and tear.

316 Stainless Steel Balls—Won't corrode from salt water or harsh chemicals, such as bleach and chlorine found in cleaning solutions.

						Temp. Range, ° F				316 Stainless Steel Balls
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	ABEC Rating	Bearing Trade No.		Each
Open







				Acetal

				4	13	5	15	3,100	-40	180	Not Rated	624	6455K91	00000

Lubrication-Free Corrosion-Resistant Swivel Joints

A slippery PTFE liner reduces wear and eliminates the need for lubrication. Also known as spherical bearings, they support angular misalignment. Press them into a hole or housing where a ball joint rod end won’t fit.

						Temp., ° F
ID, mm	OD, mm	Overall Thk., mm	Housing Thk., mm	Max. Ball Swivel	Static Radial Load Cap., lb.	Min.	Max.	Material		Each



	5	13	8	6	26°	2,800	-50	390	316 Stainless Steel	63215K111	000000

Dry-Running Sleeve Bearings

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

Nylon—The most popular choice, nylon is wear resistant yet economical. Keep in mind, though, that it will swell and weaken when exposed to moisture.

								Each
	For Shaft Dia., mm	For Housing ID, mm	Lg., mm	Dynamic Radial Load Cap. @ Speed	Color	Temp. Range, ° F		1-24	25-99	100-Up
Nylon



		10	13	10	31 lb. @ 120 rpm	Off-White	-10 to 220	6389K738	000000	00000	00000


		10	13	12	37 lb. @ 120 rpm	Off-White	-10 to 220	6389K739	00000	0000	0000
		10	13	20	60 lb. @ 120 rpm	Off-White	-10 to 220	6389K741	00000	00000	0000

Ball Joint Rod End Seals


Shown Installed

Keep dirt out and lubrication in to extend the life of your rod ends. Seals are Buna-N with a stainless steel washer for corrosion resistance. Use them between the head of your rod end and your fastener.

For Rod End ID, mm	ID, mm	OD, mm	Overall Ht., mm	Material	Washer Material		Pair
6	6	13	3	Buna-N	304 Stainless Steel	4737T12	00000

Clear Ultra-Impact-Resistant Polycarbonate Round Tubes

Comparable to Lexan, Hyzod, Tuffak, and Makrolon, these polycarbonate tubes are half the weight of glass and maintain excellent impact resistance across a wide temperature range. Use them to make instrument gauge covers and display racks.

Metric

Image of Product. Front orientation. Plastic. Clear Ultra-Impact-Resistant Polycarbonate Round Tubes.

									8 ft. Long
	OD, mm	ID, mm	Fabrication	Temp., ° F	Tensile Strength, psi	Impact Strength, ft·lbf/in	Flammability Rating	Food Industry Std.		Each
2.000 mm Thick Wall (-0.260 mm to 0.260 mm Tolerance)



		13	9	Extruded	-40 to 200	8,900 to 9,500	12 to 18	UL 94 HB	FDA Standard	8585K829	000000