About Rod Ends
More
About Ball and Roller Bearings
More
About Plain Bearings
More
About Linear Bearings
More
Stainless Steel Ball Bearings
Bearings are 440C stainless steel for good corrosion resistance.
Shielded bearings block out dust and other contaminants, but do not dissipate heat as efficiently as open bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
148-2Z | 8mm | 14mm | 4mm | 440C Stainless Steel | 180 | 70 | 45,000 | Lubricated | -40° to 240° | ABEC-5 | 00000000 | 00000 |
605-2Z | 5mm | 14mm | 5mm | 440C Stainless Steel | 290 | 110 | 48,000 | Lubricated | -40° to 240° | ABEC-5 | 00000000 | 0000 |
687-2Z | 7mm | 14mm | 5mm | 440C Stainless Steel | 260 | 100 | 45,000 | Lubricated | -40° to 240° | ABEC-5 | 00000000 | 0000 |
Permanently Lubricated Stainless Steel Ball Bearings
A solid polymer lubricant surrounds the balls, eliminating the need for additional lubrication. The solid lubricant blocks out water and dust, extending the life of the bearing.
Sealed bearings have even better resistance to dust and contaminants than open bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Open | ||||||||||||
605 | 5 | 14 | 5 | 440C Stainless Steel | 230 | 110 | 31,000 | Lubricated | -10° to 200° | ABEC-1 | 00000000 | 000000 |
679 | 9 | 14 | 3 | 440C Stainless Steel | 200 | 100 | 26,000 | Lubricated | -10° to 200° | ABEC-1 | 00000000 | 00000 |
687 | 7 | 14 | 3.5 | 440C Stainless Steel | 200 | 100 | 30,000 | Lubricated | -10° to 200° | ABEC-1 | 00000000 | 00000 |
Sealed | ||||||||||||
605-2RS | 5 | 14 | 5 | 440C Stainless Steel | 230 | 110 | 31,000 | Lubricated | -10° to 200° | ABEC-1 | 00000000 | 00000 |
687-2RS | 7 | 14 | 5 | 440C Stainless Steel | 200 | 100 | 30,000 | Lubricated | -10° to 200° | ABEC-1 | 00000000 | 00000 |
Precision Stainless Steel Ball Bearings
Made to tight tolerances, these 440C stainless steel bearings combine speed and accuracy with corrosion resistance.
Open bearings dissipate heat more efficiently than shielded bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
Open | |||||||||||
7mm | 14mm | 3.5mm | 440C Stainless Steel | 160 | 50 | 38,000 | Lubricated | -30° to 280° | ABEC-7 | 0000000 | 000000 |
Food Industry Permanently Lubricated Stainless Steel Ball Bearings
Good for applications with incidental food contact, these 440C stainless steel bearings have a food-grade, solid polymer lubricant between the balls and ring that eliminates the need for additional lubrication. The solid lubricant blocks out water and dust, extending the life of the bearing.
Sealed bearings have even better resistance to dust and contaminants than open bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia., mm | For Housing ID, mm | Wd., mm | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Specifications Met | Each | |
Sealed | |||||||||||||
605-2RS | 5 | 14 | 5 | 440C Stainless Steel | 290 | 110 | 31,500 | Lubricated | -40° to 200° | ABEC-1 | FDA Compliant 21 CFR 178.3570 | 00000000 | 000000 |
Flanged Ball Bearings
The flange ensures proper positioning inside a tube or housing.
440C stainless steel bearings are more corrosion resistant than steel bearings.
Open bearings dissipate heat more efficiently than shielded and sealed bearings.
Shielded bearings block out dust and other contaminants, but do not dissipate heat as efficiently as open bearings.
For technical drawings and 3-D models, click on a part number.
Flange | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
148 | 8mm | 14mm | 3.5mm | 15.6mm | 0.8mm | 440C Stainless Steel | 140 | 65 | 50,000 | Lubricated | -50° to 300° | ABEC-3 | 000000000 | 000000 |
148 | 8mm | 14mm | 3.5mm | 15.6mm | 0.8mm | Steel | 180 | 85 | 50,000 | Lubricated | -50° to 300° | ABEC-3 | 000000000 | 0000 |
605 | 5mm | 14mm | 5mm | 16mm | 1mm | 440C Stainless Steel | 230 | 90 | 56,000 | Lubricated | -50° to 300° | ABEC-3 | 000000000 | 00000 |
605 | 5mm | 14mm | 5mm | 16mm | 1mm | Steel | 290 | 110 | 56,000 | Lubricated | -50° to 300° | ABEC-3 | 000000000 | 00000 |
Flange | Radial Load Cap., lbs. | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Bearing Trade Number | For Shaft Dia. | For Housing ID | Wd. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | ABEC Rating | Each | |
148-2Z | 8mm | 14mm | 4mm | 15.6mm | 0.8mm | 440C Stainless Steel | 140 | 65 | 42,000 | Lubricated | -50° to 300° | ABEC-3 | 000000000 | 000000 |
148-2Z | 8mm | 14mm | 4mm | 15.6mm | 0.8mm | 440C Stainless Steel | 180 | 70 | 45,000 | Lubricated | -20° to 250° | ABEC-5 | 00000000 | 0000 |
148-2Z | 8mm | 14mm | 4mm | 15.6mm | 0.8mm | Steel | 180 | 85 | 42,000 | Lubricated | -50° to 300° | ABEC-3 | 000000000 | 00000 |
605-2Z | 5mm | 14mm | 5mm | 16mm | 1mm | 440C Stainless Steel | 230 | 90 | 48,000 | Lubricated | -50° to 300° | ABEC-3 | 000000000 | 00000 |
605-2Z | 5mm | 14mm | 5mm | 16mm | 1mm | Steel | 290 | 110 | 48,000 | Lubricated | -50° to 300° | ABEC-3 | 000000000 | 00000 |
687-2Z | 7mm | 14mm | 5mm | 16mm | 1.1mm | 440C Stainless Steel | 210 | 90 | 44,000 | Lubricated | -50° to 300° | ABEC-3 | 000000000 | 00000 |
Thrust Ball Bearings
Steel balls and washers allow these bearings to handle higher loads than bearings with stainless steel components. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
Bearings with steel cage and with bronze cage handle higher loads and speeds than bearings with a plastic cage.
For technical drawings and 3-D models, click on a part number.
Corrosion-Resistant Thrust Ball Bearings
A combination of stainless steel and nylon components provide increased corrosion resistance over standard thrust ball bearings. With an open design, they dissipate heat more efficiently than one-piece thrust ball bearings.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | OD | Thick. | Cage Material | Washer Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Includes | Each | |
Open | ||||||||||||
6mm | 14mm | 4.92mm | Nylon Plastic | 410 Stainless Steel | 10 | 90 | 5,000 | Required | -40° to 220° | Two Washers | 0000000 | 00000 |
Needle-Roller Bearings
Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.
Open bearings dissipate heat more efficiently than sealed bearings.
Sealed bearings block out dust better than open bearings, but retain more heat.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range, °F | Specifications Met | Each | |
Open | ||||||||||||
10mm | 14mm | 10mm | Steel | 990 | 1,150 | 24,300 | Required | 8 | -40° to 280° | DIN 618, ISO 3245 | 00000000 | 00000 |
10mm | 14mm | 12mm | Steel | 1,200 | 1,500 | 24,300 | Required | 8 | -20° to 280° | DIN 618, ISO 3245 | 00000000 | 0000 |
10mm | 14mm | 15mm | Steel | 1,500 | 1,950 | 24,300 | Required | 8 | -20° to 280° | DIN 618, ISO 3245 | 00000000 | 0000 |
Sealed—Both Sides | ||||||||||||
10mm | 14mm | 12mm | Steel | 700 | 750 | 14,600 | Lubricated | 8 | 0° to 210° | DIN 618 | 00000000 | 00000 |
10mm | 14mm | 14mm | Steel | 980 | 1,100 | 14,600 | Lubricated | 8 | -20° to 210° | DIN 618, ISO 3245 | 00000000 | 00000 |
Shaft Liners for Precision Needle-Roller Bearings
Adapt high-precision needle-roller bearings to use on unhardened, unground shafts. The liner fits between the roller and the shaft.
For technical drawings and 3-D models, click on a part number.
For Shaft Dia. | OD | Wd. | Ring Material | Lubrication | Specifications Met | Each | |
10mm | 14mm | 16mm | Steel | Required | DIN 620 | 0000000 | 00000 |
One-Way Locking Needle-Roller Bearing Clutches
The needles in these bearings roll freely in one direction, but lock to transmit torque when the rotation of the shaft is reversed. Also known as drawn-cup roller clutches. An arrow on the lip indicates the rotational direction that locks the bearings.
Triple-row bearings support radial loads.
Bearings with 301 stainless steel springs handle higher temperatures than bearings with acetal springs.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | For Housing ID | Wd. | Ring Material | Dynamic | Static | Max. Speed, rpm | Max. Torque, ft.-lbs. | Lubrication | For Shaft Surface Smoothness (Ra), microinch | Temp. Range, °F | Each | |
Triple Row | ||||||||||||
301 Stainless Steel Springs | ||||||||||||
8mm | 14mm | 20mm | Steel | 940 | 680 | 21,000 | 3.2 | Required | 16 | -20° to 250° | 0000000 | 000000 |
Needle-Roller Thrust Bearings
Thinner rollers allow these bearings to fit in tighter spaces than tapered-roller thrust bearings. Because of the large contact area between the rollers and washers (not included), these bearings are great for medium to heavy duty, low-friction jobs. For use on hardened and ground surfaces.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|
For Shaft Dia. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microns | Temp. Range, °F | Specifications Met | Each | |
Steel Rollers | |||||||||||
Open | |||||||||||
4mm | 14mm | 2mm | 1,000 | 1,800 | 21,000 | Required | 0.2 | 0° to 240° | DIN 5405-2 | 000000 | 00000 |
For Shaft Dia. | OD | Thick. | Washer Material | Specifications Met | Each | |
4mm | 14mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 00000 |
Washers for Needle-Roller Thrust Bearings
Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
For technical drawings and 3-D models, click on a part number.
For Shaft Dia. | OD | Thick. | Washer Material | Specifications Met | Each | |
4mm | 14mm | 1mm | Steel | DIN 5405-3, ISO 303 | 00000000 | 00000 |
High-Load Oil-Embedded Sleeve Bearings
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds. Startup friction causes them to release a thin layer of oil on the bearing’s surface. Color is silver because of the iron. These bearings are also magnetic due to the high iron content.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Dynamic Radial Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 10mm Shaft Dia. | |||||||
---|---|---|---|---|---|---|---|
14mm | 8mm | 750 lbs. @ 120 rpm | Lubricated | SAE 90 Oil | 10° to 510° | 00000000 | 000000 |
14mm | 10mm | 930 lbs. @ 120 rpm | Lubricated | SAE 90 Oil | 10° to 510° | 00000000 | 00000 |
14mm | 14mm | 1,300 lbs. @ 120 rpm | Lubricated | SAE 90 Oil | 10° to 510° | 00000000 | 00000 |
14mm | 16mm | 1,500 lbs. @ 120 rpm | Lubricated | SAE 90 Oil | 10° to 510° | 00000000 | 00000 |
14mm | 25mm | 2,300 lbs. @ 120 rpm | Lubricated | SAE 90 Oil | 10° to 510° | 00000000 | 00000 |
Light Duty Dry-Running Sleeve Bearings
Use where high loads and speeds are not required.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Water-Resistant Dry-Running Sleeve Bearings
Good for underwater applications, these bearings won’t swell or warp when wet.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
ID | For Housing ID | Lg. | Dynamic Radial Load Capacity | Color | Temperature Range, °F | Each | |
Rulon LR Plastic Bearings | |||||||
---|---|---|---|---|---|---|---|
For 10mm Shaft Dia. | |||||||
10mm | 14mm | 10mm | 125 lbs. @ 120 rpm | Maroon | -400° to 500° | 00000000 | 000000 |
Light Duty Dry-Running Flanged Sleeve Bearings
Use where high loads and speeds are not required.
Thermoplastic-blend bearings have low moisture absorption and create very low friction in applications with light loads, and frequent starts and stops.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Color | Temperature Range, °F | Each | |
Thermoplastic-Blend Bearings | |||||||||
---|---|---|---|---|---|---|---|---|---|
For 10mm Shaft Dia. | |||||||||
14mm | 14mm | 17.5mm | 1mm | 170 lbs. @ 120 rpm | 110 lbs. @ 120 rpm | Yellow | -50° to 190° | 00000000 | 00000 |
For 12mm Shaft Dia. | |||||||||
14mm | 4.5mm | 18mm | 1mm | 50 lbs. @ 120 rpm | 95 lbs. @ 120 rpm | Yellow | -50° to 190° | 00000000 | 0000 |
14mm | 10mm | 18mm | 1mm | 120 lbs. @ 120 rpm | 95 lbs. @ 120 rpm | Yellow | -50° to 190° | 00000000 | 0000 |
Corrosion-Resistant Flanged Sleeve Bearings
The addition of iron and aluminum gives these bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
For Housing ID | Lg. | Flange OD | Flange Thick. | Dynamic Radial Load Capacity | Dynamic Thrust Load Capacity | Lubrication | Temperature Range, °F | Each | |
954 Aluminum-Bronze Bearings | |||||||||
---|---|---|---|---|---|---|---|---|---|
For 8mm Shaft Dia. | |||||||||
14mm | 12mm | 20mm | 3mm | 660 lbs. @ 120 rpm | 1,800 lbs. @ 120 rpm | Required | -350° to 500° | 00000000 | 00000 |
14mm | 20mm | 20mm | 3mm | 1,100 lbs. @ 120 rpm | 1,800 lbs. @ 120 rpm | Required | -350° to 500° | 00000000 | 00000 |
For 12mm Shaft Dia. | |||||||||
14mm | 12mm | 16mm | 1mm | 1,000 lbs. @ 120 rpm | 610 lbs. @ 120 rpm | Required | -350° to 500° | 00000000 | 0000 |
14mm | 20mm | 16mm | 1mm | 1,650 lbs. @ 120 rpm | 610 lbs. @ 120 rpm | Required | -350° to 500° | 00000000 | 0000 |
Oil-Embedded Thrust Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
OD, mm | Thick., mm | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 7 mm Shaft Dia. | |||||||
---|---|---|---|---|---|---|---|
14 | 1.5 | 500 lbs. @ 120 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 00000000 | 000000 |
Linear Bearings for Ball Splines
Combine these bearings with a ball spline to create a compact linear and rotary motion system for applications with fast, complex movements, such as robotics. These bearings move smoothly and precisely even at high speeds along ball splines while grooves on the ball spline transmit rotary power. Clip a retaining ring into the groove on these bearings to position them in your system. Use the keyway and included machine key for attaching your load.
Stainless steel bearings are more corrosion resistant than steel bearings.
Splines are alloy steel for high strength and wear resistance. They're hardened only on the outside, so they stand up to repeated motion while keeping their center soft enough to absorb stress from shifting loads.
For technical drawings and 3-D models, click on a part number.
Groove | Keyway | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Spline Dia., mm | For No. of Splines | Overall Lg., mm | OD, mm | Dynamic Load Capacity, lbs. | Static Load Capacity, lbs. | Max. Dynamic Torque, in.-lbs. | Max. Static Torque, in.-lbs. | Max. Temp., °F | With Retaining Ring Grooves | Wd., mm | Dia., mm | Includes | Lg., mm | Wd., mm | Dp., mm | Each | |
6 | 4 | 25 | 14 | 270 | 510 | 13 | 21 | 176° | Yes | 1.3 | 13.3 | Machine Key | 10.5 | 2.5 | 1.2 | 00000000 | 000000 |
Groove | Keyway | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Spline Dia., mm | For No. of Splines | Overall Lg., mm | OD, mm | Dynamic Load Capacity, lbs. | Static Load Capacity, lbs. | Max. Dynamic Torque, in.-lbs. | Max. Static Torque, in.-lbs. | Max. Temp., °F | With Retaining Ring Grooves | Wd., mm | Dia., mm | Includes | Lg., mm | Wd., mm | Dp., mm | Each | |
6 | 4 | 25 | 14 | 270 | 510 | 13 | 21 | 176° | Yes | 0.6 | 13.4 | Machine Key | 10.5 | 2.5 | 1.2 | 00000000 | 0000000 |
Mounted Linear Bearings for Ball Splines
A flange with mounting holes makes it easy to attach a load to these bearings. Create a compact linear and rotary motion system for robots and other applications requiring complex, fast movements, by combining them with ball splines. These bearings move smoothly and precisely even at high speeds along ball splines while grooves on the ball spline transmit rotary power. Clip a retaining ring (not included) into the groove on these bearings to position them in your system.
Splines are alloy steel for high strength and wear resistance. They're hardened only on the outside, so they stand up to repeated motion while keeping their center soft enough to absorb stress from shifting loads.
For technical drawings and 3-D models, click on a part number.
Groove | Mounting Holes | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
For Spline Dia., mm | For No. of Splines | Overall Lg., mm | Flange OD, mm | Bolt Circle Dia., mm | OD, mm | Dynamic Load Capacity, lbs. | Static Load Capacity, lbs. | Max. Dynamic Torque, in.-lbs. | Max. Static Torque, in.-lbs. | Max. Temperature, ° F | With Retaining Ring Grooves | Wd., mm | Dia., mm | No. of | Thread Size | Each | |
6 | 4 | 25 | 30 | 22 | 14 | 270 | 510 | 13 | 21 | 176° | Yes | 1.25 | 13.7 | 4 | M3 × 0.5 mm | 00000000 | 000000 |
Ball Joint Rod End Inserts
Without changing the ID, these inserts handle some misalignment on rod ends. They attach to your rod end to move your fastener away from the rod-end body.
Cone-style inserts help position rod ends between receiving forks, straps, and clevises.
For technical drawings and 3-D models, click on a part number.
For Rod End ID | ID | OD | Overall Ht. | Each | |
Cone | |||||
---|---|---|---|---|---|
Chrome-Plated Carbon Steel | |||||
6mm | 6mm | 14mm | 9mm | 000000000 | 000000 |
Metric Press-Fit Drill Bushings
Also known as jig bushings, these metric drill bushings fit inside fixture plate holes to guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so that your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings. These bushings are made of hardened, ground steel that holds its shape and resists wear, so they last for many cycles without needing to be replaced.
All bushings have a chamfer on the outside that centers the bushing as you place it into the hole. Press into place with a manual or hydraulic press. They also have internal chamfers, so it's easier to insert bits, pins, and punches into the bushing. Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Tolerance | Each | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
OD, mm | Lg., mm | Internal Chamfer | For Drill Bit Size | ID, mm | OD, mm | Lg., mm | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
10 mm ID | |||||||||||||
14 | 25 | One End | 10 mm | 0.005 to 0.014 | 0.028 to 0.039 | -0.02 to 0.2 | PM | Steel | Rockwell C61 | 0000000 | 00000 | 00000 | 00000 |
Ring Shims
Precisely align, level, and adjust spacing on fasteners, shafts, and machinery with these shims.
For accurate leveling, choose materials such as steel or stainless steel, which are hard enough to resist scratching and deforming. Softer shims, like copper or aluminum, can be used as wear plates between components that rub together, preventing damage to equipment.
Stainless steel shims are more corrosion resistant than steel shims. 316 stainless steel shims have the best corrosion resistance of our stainless steel shims.
Carbon steel shims have excellent strength and can be welded, but aren't as corrosion resistant as other shims.
Spring steel shims are comparable in strength to carbon steel shims, but are harder and hold their shape better. They aren't as corrosion resistant as other shims.
Brass and copper shims are corrosion resistant and nonmagnetic. Copper shims are good conductors of heat and electricity, so these shims are often used when installing heat sinks.
For technical drawings and 3-D models, click on a part number.
ID | ID Tolerance | OD | OD Tolerance | Material | Min. Hardness | Specifications Met | Pkg. Qty. | Pkg. | |
0.1 mm Thick. (-0.013 mm to 0.013 mm Tolerance) | |||||||||
---|---|---|---|---|---|---|---|---|---|
8mm | -0.3mm to 0.3mm | 14mm | -0.05mm to 0.05mm | 316 Stainless Steel | Rockwell B70 | __ | 10 | 000000000 | 000000 |
0.2 mm Thick. (-0.023 mm to 0.023 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.05mm to 0.05mm | 316 Stainless Steel | Rockwell B70 | __ | 10 | 000000000 | 00000 |
0.3 mm Thick (-0.015 mm to 0.015 mm Tolerance) | |||||||||
8mm | -0.13mm to 0.13mm | 14mm | -0.13mm to 0.13mm | 316 Stainless Steel | Rockwell B70 | ASTM A240 | 1 | 000000000 | 0000 |
0.5 mm Thick. (-0.064 mm to 0.064 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.05mm to 0.05mm | 316 Stainless Steel | Rockwell B70 | __ | 10 | 000000000 | 00000 |
1 mm Thick. (-0.105 mm to 0.105 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.05mm to 0.05mm | 316 Stainless Steel | Rockwell B70 | __ | 10 | 000000000 | 00000 |
2 mm Thick. (-0.29 mm to 0.08 mm Tolerance) | |||||||||
8mm | -0.13mm to 0.13mm | 14mm | -0.13mm to 0.13mm | 316 Stainless Steel | Rockwell B70 | ASTM A240 | 1 | 000000000 | 0000 |
ID | ID Tolerance | OD | OD Tolerance | Material | Min. Hardness | Pkg. Qty. | Pkg. | |
0.1 mm Thick. (-0.013 mm to 0.013 mm Tolerance) | ||||||||
---|---|---|---|---|---|---|---|---|
8mm | -0.3mm to 0.3mm | 14mm | -0.05mm to 0.05mm | 18-8 Stainless Steel | Rockwell B70 | 50 | 000000000 | 000000 |
0.2 mm Thick. (-0.023 mm to 0.023 mm Tolerance) | ||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.05mm to 0.05mm | 18-8 Stainless Steel | Rockwell B70 | 25 | 000000000 | 0000 |
0.3 mm Thick. (-0.055 mm to 0.055 mm Tolerance) | ||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.05mm to 0.05mm | 18-8 Stainless Steel | Rockwell B70 | 25 | 000000000 | 0000 |
0.5 mm Thick. (-0.064 mm to 0.064 mm Tolerance) | ||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.05mm to 0.05mm | 18-8 Stainless Steel | Rockwell B70 | 25 | 000000000 | 0000 |
1 mm Thick. (-0.105 mm to 0.105 mm Tolerance) | ||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.05mm to 0.05mm | 18-8 Stainless Steel | Rockwell B70 | 25 | 000000000 | 0000 |
1.5 mm Thick. (-0.14 mm to 0.14 mm Tolerance) | ||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.05mm to 0.05mm | 18-8 Stainless Steel | Rockwell B70 | 10 | 000000000 | 0000 |
2 mm Thick. (-0.21 mm to 0.21 mm Tolerance) | ||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.05mm to 0.05mm | 18-8 Stainless Steel | Rockwell B70 | 10 | 000000000 | 0000 |
ID | ID Tolerance | OD | OD Tolerance | Material | Min. Hardness | Pkg. Qty. | Pkg. | |
0.1 mm Thick. (-0.013 mm to 0.013 mm Tolerance) | ||||||||
---|---|---|---|---|---|---|---|---|
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 1008-1010 Carbon Steel | Rockwell B40 | 5 | 00000000 | 00000 |
0.2 mm Thick. (-0.045 mm to 0.045 mm Tolerance) | ||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 1008-1010 Carbon Steel | Rockwell B40 | 5 | 00000000 | 0000 |
0.3 mm Thick. (-0.072 mm to 0.072 mm Tolerance) | ||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 1008-1010 Carbon Steel | Rockwell B40 | 5 | 00000000 | 0000 |
0.5 mm Thick. (-0.064 mm to 0.064 mm Tolerance) | ||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 1008-1010 Carbon Steel | Rockwell B40 | 100 | 00000000 | 0000 |
1 mm Thick. (-0.105 mm to 0.105 mm Tolerance) | ||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 1008-1010 Carbon Steel | Rockwell B40 | 100 | 00000000 | 0000 |
1.5 mm Thick. (-0.14 mm to 0.14 mm Tolerance) | ||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 1008-1010 Carbon Steel | Rockwell B40 | 100 | 00000000 | 0000 |
2 mm Thick. (-0.21 mm to 0.21 mm Tolerance) | ||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 1008-1010 Carbon Steel | Rockwell B40 | 100 | 00000000 | 00000 |
ID | ID Tolerance | OD | OD Tolerance | Material | Min. Hardness | Specifications Met | Pkg. Qty. | Pkg. | |
0.1 mm Thick. (-0.03 mm to 0 mm Tolerance) | |||||||||
---|---|---|---|---|---|---|---|---|---|
8mm | 0.03mm to 0.4mm | 14mm | -0.47mm to -0.04mm | 1074-1095 Spring Steel | Rockwell B85 | DIN 988 | 50 | 000000000 | 00000 |
0.2 mm Thick. (-0.04 mm to 0 mm Tolerance) | |||||||||
8mm | 0.03mm to 0.4mm | 14mm | -0.47mm to -0.04mm | 1074-1095 Spring Steel | Rockwell B85 | DIN 988 | 50 | 000000000 | 0000 |
0.3 mm Thick. (-0.05 mm to 0 mm Tolerance) | |||||||||
8mm | 0.03mm to 0.4mm | 14mm | -0.47mm to -0.04mm | 1074-1095 Spring Steel | Rockwell B85 | DIN 988 | 50 | 000000000 | 0000 |
0.5 mm Thick. (-0.05 mm to 0 mm Tolerance) | |||||||||
8mm | 0.03mm to 0.4mm | 14mm | -0.47mm to -0.04mm | 1074-1095 Spring Steel | Rockwell B85 | DIN 988 | 50 | 000000000 | 0000 |
1 mm Thick. (-0.05 mm to 0 mm Tolerance) | |||||||||
8mm | 0.03mm to 0.4mm | 14mm | -0.47mm to -0.04mm | 1074-1095 Spring Steel | Rockwell B85 | DIN 988 | 50 | 000000000 | 0000 |
2 mm Thick. (-0.2 mm to 0 mm Tolerance) | |||||||||
8mm | -0.4mm to 0.4mm | 14mm | -0.47mm to 0.4mm | 1074-1095 Spring Steel | Rockwell C40 | __ | 25 | 000000000 | 0000 |
ID | ID Tolerance | OD | OD Tolerance | Material | Min. Hardness | Specifications Met | Pkg. Qty. | Pkg. | |
0.1 mm Thick. (-0.013 mm to 0.013 mm Tolerance) | |||||||||
---|---|---|---|---|---|---|---|---|---|
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 260-360 Brass | Rockwell B14 | ASTM B36 | 5 | 000000000 | 00000 |
0.2 mm Thick. (-0.045 mm to 0.045 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 260-360 Brass | Rockwell B14 | ASTM B36 | 5 | 000000000 | 0000 |
0.3 mm Thick. (-0.072 mm to 0.072 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 260-360 Brass | Rockwell B14 | ASTM B36 | 5 | 000000000 | 0000 |
0.5 mm Thick. (-0.064 mm to 0.064 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 260-360 Brass | Rockwell B14 | ASTM B36 | 25 | 000000000 | 00000 |
1 mm Thick. (-0.105 mm to 0.105 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 260-360 Brass | Rockwell B14 | ASTM B36 | 25 | 000000000 | 00000 |
1.5 mm Thick. (-0.14 mm to 0.14 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 260-360 Brass | Rockwell B14 | ASTM B36 | 10 | 000000000 | 0000 |
2 mm Thick. (-0.21 mm to 0.21 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 260-360 Brass | Rockwell B14 | ASTM B36 | 10 | 000000000 | 0000 |
ID | ID Tolerance | OD | OD Tolerance | Material | Min. Hardness | Specifications Met | Pkg. Qty. | Pkg. | |
0.1 mm Thick. (-0.013 mm to 0.013 mm Tolerance) | |||||||||
---|---|---|---|---|---|---|---|---|---|
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 110 Copper | Rockwell F40 | ASTM B152 | 5 | 000000000 | 00000 |
0.2 mm Thick. (-0.045 mm to 0.045 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 110 Copper | Rockwell F40 | ASTM B152 | 5 | 000000000 | 0000 |
0.3 mm Thick. (-0.072 mm to 0.072 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 110 Copper | Rockwell F40 | ASTM B152 | 5 | 000000000 | 0000 |
0.5 mm Thick. (-0.064 mm to 0.064 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 110 Copper | Rockwell F40 | ASTM B152 | 25 | 000000000 | 00000 |
1 mm Thick. (-0.105 mm to 0.105 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 110 Copper | Rockwell F40 | ASTM B152 | 10 | 000000000 | 0000 |
1.5 mm Thick. (-0.14 mm to 0.14 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 110 Copper | Rockwell F40 | ASTM B152 | 10 | 000000000 | 0000 |
2 mm Thick. (-0.21 mm to 0.21 mm Tolerance) | |||||||||
8mm | -0.3mm to 0.3mm | 14mm | -0.5mm to 0.5mm | 110 Copper | Rockwell F40 | ASTM B152 | 10 | 000000000 | 0000 |