Minimize false triggers—these switches require 10 lbs. of actuation force in order to shut off machinery immediately. Combine with a controller (sold separately) to create a self-monitoring system that also shuts off machinery when a fault is detected. They’re sensitive along their entire length and often used to signal when an overhead door closes or when an item reaches the end of a conveyor. The attached mounting channel can be mounted to a door or flat surface. Punch or drill holes into the channel to match an existing hole pattern or create a new mounting pattern. Switches are rated IP65 for protection from washdowns.

Sealed actuators prevent these switches from jamming, even when exposed to oil, sand, mud, or ice. They send a signal to your circuit when an object hits the actuator—for instance, a box on a conveyor runs into the switch, stopping the conveyor. They open and close circuits as fast as snap-acting switches, but they have a bigger actuator for large objects. To actuate, they require a push, similar to a button. Rated IP68, they’re protected against dust and temporary submersion.

Switches with a stainless steel housing stand up better to wear and tear and corrosion better than switches with a zinc-plated steel housing.

Step or press anywhere along the switch to control doors, lights, or alarms. These switches are often placed across driveways and walkways to detect foot and vehicle traffic. Rated IP67, they can be temporarily submerged in puddles without the water harming their internal parts. These switches are bright yellow, so they can easily be spotted from far away. Made from PVC, they are flexible enough to conform to irregular and uneven surfaces.

Made with stainless steel conductors, these switches resist corrosion in damp areas. They’re less than 1/4” thick, so they’ll fit under floor mats and in other tight spaces. Control doors, lights, and alarms by pressing or stepping anywhere along the switch to actuate it. They’re more rigid than other strip switches, so mounting channels aren’t necessary—just stick them in place with mounting tape.

These narrow switches are also thin enough to be hidden under carpeting or installed anywhere space is limited. Actuate them anywhere along the length of the switch.

Optional mounting channels secure switches to a flat surface.

Customize the length of these switches by cutting them from a 50-foot roll. They're narrow and thin, so they can be hidden under carpeting or installed anywhere space is limited. Actuate them anywhere along the length of the switch. A complete system includes a strip switch and a termination kit (sold separately).

Optional mounting channels secure switches to a flat surface.

Use surface fillers for vinyl fabric (not included) to seal ends.

With a smaller footprint than other switch mats, these fit in confined spaces.

Rated IP67 and NEMA 6, these switch mats withstand washdowns and temporary submersion. They have a smaller footprint than other switch mats to fit in confined spaces.

Customize the length of these switches by cutting them from a 25-foot roll. The width cannot be cut. They fit under carpeting or anywhere else you want to hide them. Mats have bare wires that solder or crimp to a connector.

These mats fit under carpeting or anywhere else you want to hide them.

Step on these mats to control doors, lights, or alarms.

Prevent personnel from getting too close to dangerous equipment while it’s running. Step anywhere on these mats and they can turn on warning lights and alarms or shut down equipment. To minimize circuit damage, they also activate if they detect any malfunctions in your equipment’s electrical system. A complete switch requires a mat and a controller (sold separately). Together they meet ANSI/RIA R15.06 safety requirements. Mats are rated IP65 for protection from washdowns.

Red mats are easy to spot in crowded areas and in dim light. They help you avoid stepping on them if you don’t want to stop machinery or to find them quickly if you do.

Mats with diamond tread have a raised pattern on the surface to add traction and prevent slipping. Made from aluminum, they’re more durable than plastic mats, and less likely to be punctured or damaged by impact. However, they’re also more rigid than plastic mats, so they can only be used on flat surfaces. These mats are often used in high-traffic welding shops and freight warehouses.

Optional frames secure mats to the floor. Punch holes in the frame to insert a screw anywhere along the length.