McMaster-Carr logo
    Filter by
    System of Measurement
    For Housing ID
    Attribute Image
    Bearing Type
    Length
    Attribute Image
    Construction
    Plain Bearing Type
    Bushing Trade Number
    Shaft Type
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Dynamic Radial Load Capacity @ Speed
    Lubrication
    Maximum Temperature
    Minimum Temperature
    For Load Direction
    Overall Width
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    11 Products
    About Sleeve Bearings
    industrial info icon

    Choose a sleeve bearing that matches your load and speed requirements and that's right for your environment.

    Sleeve Bearings

    Image of Product. Front orientation. Sleeve Bearings. Sleeve Bearings.
    These bearings don’t come with a lubricant, so you can select the oil that meets the needs of your application. You’ll need to refill the oil, so make sure the bearing is located where you can access it. All are fabricated and inspected in the U.S.
    With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.
    High-Load 932 Bearing Bronze—These bearings are strong enough for sudden starts and stops, plus they resist wear and tear. They are cast from an alloy of leaded tin bronze for uniform rigidity and strength. Also known as 660 leaded bronze bearings.
    For Shaft
    Dia., mm
    For Housing
    ID, mm
    Lg.,
    mm
    Dynamic Radial Load
    Cap. @ Speed
    Temp. Range,
    ° F
    Each
    High-Load 932 Bearing Bronze
    657510037,550 lb. @ 30 rpm-350 to 4507811K322000000
     

    Quick-Disconnect (QD) Bushings

    Image of Product. Front orientation. Pulley and Sprocket Bushings. Quick-Disconnect (QD) Bushings, Clamp-On Shaft Mount.
    Image of Attribute. Side1 orientation. Contains Annotated. Quick-Disconnect (QD) Bushings.

    Clamp-On Shaft Mount

    The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing trade number. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
    Keyway,
    mm
    Overall
    Wd., mm
    Wd.
    Dp.
    Fastener Tightening
    Torque, in·lbf
    Material
    Includes
    For Shaft
    Dia., mm
    Each
    Clamp-On Shaft Mount
     
    Bushing Trade Number E
    67184.4720Cast IronClamping Screws652344K920000000
     

    Set Screw Shaft Collars

    Image of Product. Front orientation. Shaft Collars. Set Screw Shaft Collars.
    Slide these traditional collars from one end of the shaft and tighten the set screw. They dig into the shaft for a secure hold, but one that leaves a gouge. For maximum holding power, make sure the set screw is harder than the shaft.
    Zinc-Plated Carbon Steel—A step up from plain carbon steel collars, these withstand occasional exposure to moisture.
    Blue Passivated Zinc-Plated Carbon Steel—Withstand moisture and mild chemicals better than standard zinc-plated-steel collars. The blue passivated finish makes it easy to identify metric collars at a glance.
    Carbon Steel—Strong and easy to machine. Use in dry environments, since moisture will cause steel to rust.
    303 Stainless Steel—Withstand moisture and mild cleaning solutions, such as acetone and ammonia. These are easier to machine than other stainless steel collars.
    Set
    Screw
    For Shaft
    Dia., mm
    OD,
    mm
    Wd.,
    mm
    Type
    No.
    Included
    Each
    Blue Passivated Zinc-Plated Carbon Steel
    6510020Hex Socket16057N49000000
     
    Carbon Steel
    6510020Hex Socket16056N4900000
     
    303 Stainless Steel
    6510020Hex Socket26058N49000000
     

    Two-Piece Shaft Collars

    Image of Product. Front orientation. Shaft Collars. Two Piece, For Round Shafts.

    For Round Shafts

    Image of Product. Front orientation. Shaft Collars. Two Piece, For Keyed Shafts.

    For Keyed Shafts

    Attach these collars anywhere along your shaft, which helps when other components are already installed or you can't access the end. They clamp firmly and evenly without marring the shaft, so you can reposition or remove collars later.
    Black-Oxide Carbon Steel—Dark and matted for a finished look, but with minimal corrosion resistance. Best for dry environments.
    Chrome-Plated Carbon Steel—Resist moisture and mild cleaning solutions better than zinc-plated collars.
    Carbon Steel—Strong and easy to machine. Use in dry environments, since moisture will cause steel to rust.
    303 Stainless Steel—Withstand moisture and mild cleaning solutions, such as acetone and ammonia. These are easier to machine than other stainless steel collars.
    Aluminum—One-third the weight of steel and corrosion resistant.
    For Round Shafts
    For Keyed Shafts
    Clamping
    Screw
    Keyway,
    mm
    For Shaft
    Dia., mm
    OD,
    mm
    Wd.,
    mm
    Type
    No.
    Included
    Each
    Wd.
    Dp.
    Each
    Black-Oxide Carbon Steel
    659319Socket Head26063K36000000184.43390N290000000
     
    Chrome-Plated Carbon Steel
    659319Socket Head23388N3400000—————0
     
    Carbon Steel
    659319Socket Head29739T52800000—————0
     
    303 Stainless Steel
    659319Socket Head23369K33000000—————0
     
    Aluminum
    659319Socket Head29520T24000000—————0
     
    back to top