We will reply to your message within an hour.
More
A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.
Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.
A molded cushion reduces vibration and wear from clamp edges, plus it provides a tighter fit around material than standard vibration-damping loop clamps.
Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.
These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.
Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.
For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.
Organize multiple lines of pipe, tubing, or hose with a single clamp. They are polyethylene for good chemical and UV resistance.
Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.
For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.
Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.
Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.
Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.
Flexible grooves inside these polypropylene clamps allow material to expand and contract. Clamps are moisture and chemical resistant.
Slide these clamps into strut channel and snap closed for quick installation with no tools required. They are noncorrosive, nonconductive nylon.
For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.
Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.
Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.
For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.
Route pipe, tubing, and conduit across strut channel.
Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.
Hold pipe, tubing, and conduit away from strut channel.
A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.
For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.
Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.
For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.
Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.
Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.
Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.
Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.
Customize these clamps to any object—they have a bend-and-stay design so you can mold them to the size and shape you need. Made of plastic-coated 316 stainless steel, they withstand abrasion, corrosion, and UV rays.
Tighten the bolt for an exact fit around material. Clamps secure vertical pipes in sanitation drain applications and prevent them from coming in contact with the mounting surface.
Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.
These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.
Clip these hangers onto the side of threaded rod. Unlike other threaded-rod-mount hangers, you can use more than one hanger on the same rod to organize multiple lines of pipe, tubing, and conduit.
A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.
Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.
Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.
Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.
Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.
These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.
Connect these hangers to organize multiple lines of pipe, tubing, and conduit. The tight-fitting, santoprene body reduces vibration and prevents corrosion caused by metal-to-metal contact.
Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.
Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.
These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.
Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.
Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.
A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.
Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.
Cut as much strap as you need to hang duct, pipe, and other materials.
Use these close-fitting hangers for a more rigid hold around material than when using straps alone.
Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.
For a strong, secure connection, mount these hangers by welding them to a rod.
A versatile solution for temporary hanging of pipe and tubing at work sites as well as anywhere welding and fastening are not possible. Feed material through the strap, then use the D-rings to adjust the hanging height.
Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.
Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.
Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.
A mounting plate provides a more secure hold at the mounting surface.
Also known as muffler clamps, these U-bolts have a rounded mounting plate that fully surrounds pipe, conduit, and tubing for a secure fit.
Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.
Suspend and route flat-bottomed objects such as strut channel and small duct.
A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.
Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.
These fiberglass-reinforced polyurethane U-bolts have no metal parts, so they won't conduct electricity or cause metal-to-metal corrosion.
Route bundles of wire and cable through a single hook. A wide opening allows access for installation, adjustment, and removal.
Keep multiple bundles of wire and cable on separate hooks. The hooks have wide openings to allow access for installation, adjustment, and removal.
Also known as bridle rings, routing rings have an open-eye design that allows you to quickly install wire and cable.
These plastic rings won't conduct electricity. Also known as distribution rings, they have a large opening for routing multiple cables. A smooth surface prevents damage to wire and cable.
Anchor these ringbolts where you need them, then remove the ring when not in use. Once installed, the mounting bolt stays in place. Insert the ring by threading into the mounting bolt; remove by unthreading it.
Mount these ringbolts into a threaded hole, or use the nut for through-hole mounting. The pivoting ring allows material to move freely.
Temporarily mount routing rings and other threaded components to steel and iron surfaces.
Hang these S-hooks from fencing and railing to route large bundles of material, such as cable, hose, and wire through your facility or worksite to avoid tripping hazards.
Hang cable and other flexible material beneath wire to prevent it from sagging and swaying. To install, hook the two ends of the ring around the wire—no fasteners required.
Combine with a U-bolt or routing clamp to convey a variety of material, such as pipe, tubing, and cable raceway, at distance from floors, walls, and ceilings. The extra clearance allows access for maintenance and adding and removing lines.
Clip these saddles around the outside of strut channel for a quick way to route insulated tubing and pipe. Lips on either end of the saddle protect insulation from abrasion if the pipe should move.
Clamp onto metal tubes such as pipe, scaffolding, and railing to hang lighting fixtures, threaded rod, and equipment.
Mount to a surface to secure and route cable.
These mounts create space between a bundle and surface.
Grip delicate cables with these holders.
Add a hook and loop cable tie to these mounts to secure a bundle.
Attach with a screw or other fastener.
Stick these ties to any smooth, clean surface.
Route and organize wire, cable, and hose along your DIN rail. Unlike zip ties, these cable ties can be temporarily undone to add or remove material.
Quickly attach and detach a bundle.
Feed a bundle through the closed loop and wrap the ends around pipe or conduit for support.
Attach these cable ties directly to a surface—no separate mount needed.
Reduce gaps between the cable tie and bundle—these ties have a smooth body that allows them to adjust to the exact size of the material.
Use in noncritical applications, such as fencing, where the strength of a forged clamp is not required. Install clamps so the saddle is on the long (live) end and the U-bolt is on the short (dead) end. They’re also known as wire rope clips.
These clamps must be oriented with the saddle on the long (live) end and the U-bolt on the short (dead) end. They’re also known as wire rope clips.
These clamps have a forged fabrication and are reliable in critical applications. They are not for making slings. These must be oriented with the saddle on the long (live) end and U-bolt on the short (dead) end. They’re also known as wire rope clips.
Constructed with a saddle for both the long (live) end and the short (dead) end, these clamps apply equal pressure without crimping or crushing the wire rope, so orientation doesn't matter. Also known as fist grip wire rope clips.
Install these clamps without any specific orientation, slide the nut over the rope and tighten it onto the threaded halves with a torque wrench.
Kits include clamps and thimbles to support a wire rope loop and prevent it from fraying. Clamps must be oriented with the saddle on the long (live) end and U-bolt on the short (dead) end.
Make a removable loop without specialty tools for use in noncritical applications, such as fencing. Also known as tiller clamps.
Create a loop by feeding the wire rope through the clamp and tighten the set screw to secure it in place. Loosen the set screw to quickly adjust the loop. Also known as Gripple rope clamps. They are for use in noncritical applications, such as fencing.
A clamp and thimble in one convenient fitting simplifies installation while providing support and fray protection to the wire rope loop. Use a torque wrench to tighten the clamp.
These compression sleeves are designed to meet lifting specifications.
Use these sleeves for non-lifting applications such as tethering, securing, and suspending.
Keep multiple sleeves on hand in a variety of sizes.
These kits include two compression sleeves paired with two thimbles. The thimbles support the wire rope loops and prevent it from fraying.
Install these clevis-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.
Install these stud-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.
Install these eye-end plug-lock fittings on the end of wire rope for a strong hold and finished appearance.
Add an eye-end to wire rope without having to fray the rope or use a compression tool.
Add a clevis end to wire rope without having to fray the rope or use a compression tool.
Also known as open wedge sockets, these end fittings require only a torque wrench to install.
Compress sleeves with less effort than standard compression tools.
Compress sleeves with more force than hydraulic hand tools.
Install with a compression tool to create a strong, permanent loop.
Make a removable loop without specialty tools–secure the two halves of these clamps with a screwdriver and the included screws.
These are the most corrosion-resistant tray systems we offer.
The zinc plating on these tray systems offers good corrosion resistance.
Cut, bend, and connect these wire mesh tray systems to route cable and hose in configurations such as curves, slopes, and tees.
Slide these clips on DIN rails—often used in equipment cabinet racks—to route and organize cables. Since these clips don’t require adhesive or screws, you can move them anywhere along the rail.
Clip these suppressors—also known as ferrite beads and ferrite chokes—around data, USB, video, and sensitive-equipment cable to curb electromagnetic and radio frequency interference.
Lock Ethernet cords in place to prevent unauthorized removal from ports.
Route wires, cables, and tubing along T‐slotted rails.
For compatibility with quick-connect clamps to secure pipe and conduit without screws and tools, this strut channel has narrow slotted holes.
These brackets have narrow slots compatible with quick-connect clamps for securing pipe and conduit on the channel side of struts without screws or tools.
Replace worn and broken clamps on jumper cables.
Thicker wires allow for a fast start on large trucks and industrial vehicles.
These cables are for occasional use on cars and other small transport vehicles.