Add push-in cable holder to this adapter to mount cable to DIN rail.

Grip delicate cables with these holders.

Keep individual wires separate by laying them between the coils on these holders.

Quickly attach and detach a bundle.

Attach with a screw or other fastener.

Route and organize wire, cable, and hose along your DIN rail. Unlike zip ties, these cable ties can be temporarily undone to add or remove material.

These ties meet UL flammability requirements.

These ties are flexible, reusable, and adjustable for delicate bundles or bundles that frequently change in size.

Keep a set of these differently sized cable ties on hand to use when you need them. They're flexible, reusable, adjustable.

Bundle cables outdoors with these ties that withstand exposure to UV rays and water.

Ties are made from heat-resistant fabric to withstand high temperatures.

These ties stretch to hold material tightly without slipping.

The buckle allows you to cinch these ties tight.

Able to fit small bundles, these thin ties are more flexible than other ties.

Woven from flexible stainless steel yarn and Nomex, these ties handle temperatures up to 850° F.

These mounts meet UL flammability requirements.

Use these plastic mounts with metal-detector-grade cable ties when detection and retrieval is essential, such as in food processing applications. Mounts are brightly colored for visibility and contain a special compound that can be picked up by X-ray equipment and metal detectors.

Reduce gaps between the cable tie and bundle—these ties have a smooth body that allows them to adjust to the exact size of the material.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.

Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.

Flexible grooves inside these polypropylene clamps allow material to expand and contract. Clamps are moisture and chemical resistant.

For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

A molded cushion reduces vibration and wear from clamp edges, plus it provides a tighter fit around material than standard vibration-damping loop clamps.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.

Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Route bundles of wire and cable through a single hook. A wide opening allows access for installation, adjustment, and removal.

Temporarily mount routing rings and other threaded components to steel and iron surfaces.

These plastic rings won't conduct electricity. Also known as distribution rings, they have a large opening for routing multiple cables. A smooth surface prevents damage to wire and cable.

Hang cable and other flexible material beneath wire to prevent it from sagging and swaying. To install, hook the two ends of the ring around the wire—no fasteners required.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.

Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.

Connect these hangers to organize multiple lines of pipe, tubing, and conduit. The tight-fitting, santoprene body reduces vibration and prevents corrosion caused by metal-to-metal contact.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.

Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.

A versatile solution for temporary hanging of pipe and tubing at work sites as well as anywhere welding and fastening are not possible. Feed material through the strap, then use the D-rings to adjust the hanging height.

Suspend and route flat-bottomed objects such as strut channel and small duct.

Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.

These fiberglass-reinforced polyurethane U-bolts have no metal parts, so they won't conduct electricity or cause metal-to-metal corrosion.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

For compatibility with quick-connect clamps to secure pipe and conduit without screws and tools, this strut channel has narrow slotted holes.

For extra security, these have a latch that snaps back into place to secure your load.

Bend these S-hooks by hand to hang large and small objects from almost any surface.

Join, organize, and suspend objects with these S-hooks.

Use these S-hooks for lifting applications.

The most secure carabiner we offer, these carabiners won’t accidentally open when rope slides because you need to unscrew the latch to unlock them.

Prevent twisting in your rope or line with these swiveling carabiners. To open, pull the latch down, twist 90° and push in.

These snaps have an eye that rotates for easy positioning.

Lock the bolt with wire or a cable tie for a secure connection.

For a more secure connection than standard trigger-locking snaps, squeeze the trigger and slide the latch grip down to release.

Constructed with a saddle for both the long (live) end and the short (dead) end, these clamps apply equal pressure without crimping or crushing the wire rope, so orientation doesn't matter. Also known as fist grip wire rope clips.

Install these clamps without any specific orientation, slide the nut over the rope and tighten it onto the threaded halves with a torque wrench.

These clamps have a forged fabrication and are reliable in critical applications. They are not for making slings. These must be oriented with the saddle on the long (live) end and U-bolt on the short (dead) end. They’re also known as wire rope clips.

Use in noncritical applications, such as fencing, where the strength of a forged clamp is not required. Install clamps so the saddle is on the long (live) end and the U-bolt is on the short (dead) end. They’re also known as wire rope clips.