This sleeving absorbs UV light, so it can be used in direct sunlight without getting damaged. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Made with a self-extinguishing additive, this sleeving will not produce fumes when exposed to open flame or high temperatures. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

A strip of hook-and-loop creates a strong seal along the entire length of this sleeving, yet it can be opened at any point to access contents. Use it to wrap around wire, cable, or hose without disconnecting them.

Zip this sleeving around wire, cable, or hose that are connected at both ends to quickly bundle them.

The tightly braided construction makes this polyester sleeving abrasion resistant. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Often used to protect wire, cable, and hose in robotics and other automated applications, this highly flexible sleeving withstands continuous motion without tearing or fraying.

Made of aluminum with a fiberglass liner, this sleeving reflects heat away from contents and withstands temperatures up to 390°F. A slit along the entire length makes it easy to install around wire, cable, and hose without disconnecting them.

Unlike traditional sleeving that bunches wire and cable into a circle, this sleeving holds them flat, so it’s good for tight spaces such as vehicle interiors. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

This sleeving stretches to fit over items for easy installation, and then tightens around its contents for a secure fit. Choose from multiple colors to organize wire and cable.

Tested to meet MIL-STD-202, this sleeving meets performance standards for flame retardance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

With excellent torsional strength, this sleeving withstands the extreme twisting found in robotics. It has impact strength similar to steel yet is lighter than most other sleeving materials. Stretch it to fit over items for easy installation; it tightens around its contents for a secure fit.

This sleeving withstands temperatures up to 390°F and is often used to insulate connections in transformers and relays. It prevents electricity and heat from dissipating from wire and cable.

Made from thicker and denser fiberglass than standard spark-resistant sleeving, this sleeving is more abrasion resistant and provides better insulation. The silicone rubber coating protects against sparks and molten metal splash.

Use this PTFE sleeving in applications where temperatures reach up to 500° F.

With a temperature rating of 1800°F or higher, this sleeving can withstand hotter temperatures than fiberglass and most ceramic.

Unlike fiberglass and silica, this sleeving won't irritate skin, so it's easier to handle. It has a temperature rating of 1100° F or higher.

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

Made of nylon, this sleeving is the most impact- and abrasion-resistant slit corrugated sleeving we offer. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them.

This sleeving reflects heat away from contents and withstands temperatures up to 300°F. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. The corrugated construction gives it impact and abrasion resistance similar to conduit, with more flexibility.

The two halves of this sleeving nest into each other, fully enclosing contents. It has interlocking ridges that overlap to keep out dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

This sleeving reflects heat away from contents and withstands temperatures up to 900°F. The corrugated construction gives it impact and abrasion resistance similar to conduit, but with more flexibility.

A mica and silicone rubber blend allows this sleeving to withstand temperatures up to 2100° F. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

This tubing creates a tight seal over irregularly shaped objects.

The smallest heat-shrink tubing we offer, this tubing protects wire with a 0.017" and smaller diameter.

Identify ground wire with this green-and-yellow striped tubing.

Resistant to diesel fuel, hydraulic fluid, and lubricating oil, this tubing is often used in vehicles.

Create a water-resistant seal—this tubing has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.

Made of PVC, this tubing resists chemicals, oil, and solvents. The adhesive lining creates a water-resistant seal when heated.

Often used in automated applications such as robotics, this highly flexible silicone rubber tubing withstands continuous motion without cracking and tearing. It resists abrasion and can be dragged over rough surfaces without damage.

Made of woven polyolefin/polyester fabric, this tubing has excellent abrasion resistance so it can be dragged over rough surfaces without damage.

Use this tubing in applications where temperatures reach up to 500° F. It's often used to insulate electronic components.

With excellent resistance to tears and cuts, this tubing withstands demanding use.

A flame-retardant additive makes this polyolefin tubing combustion resistant and minimizes the spread of flames.

Made of PVDF, this tubing has excellent cut and abrasion resistance. It has a flame-retardant additive that resists combustion and minimizes the spread of flames.

Approved for contact with food, this tubing is FDA Compliant 21 CFR 177.1330.

Also known as breakout boots, these splitters insulate and seal the point where wire splits off from cable, or where cables exit from conduit.

Keep general purpose tubing in a variety of sizes on hand.

Create a permanent seal without applying heat. This tubing is also known as cold-shrink tubing.

Seal the end of crimped connections, such as motor coils, to protect them from moisture.

Flexible enough for small bundles, these ties are often used for electronics.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

Create custom-length ties from a roll with hook on one side and loop on the other.

These ties stretch to hold material tightly without slipping.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

These cable ties are easy to yank apart or cinch shut, even when wearing gloves—a textured tab on the end gives you a good grip.

Create a cable tie with a buckle—no sewing required.

Feed a bundle through the closed loop and wrap the ends around pipe or conduit for support.

Stick these ties to any smooth, clean surface.

The buckle allows you to cinch these ties tight.

These cable ties come with a material certificate with traceable lot number and product shelf life.

These ties meet UL flammability requirements.

With a thin, flexible body, these cable ties fit tightly around irregularly shaped bundles.

The head of these cable ties is contoured to fit against pipe, tubing, and other round material for a tight fit.

These ties are less likely to crack and break from dryness than regular cable ties.

Use these plastic cable ties when detection and retrieval are essential, such as in food processing applications. Ties are brightly colored for visibility and contain a special compound that can be picked up by X-ray equipment and metal detectors.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

Often used as tamper seals and in tagging applications, these ties create a consistent loop size every time.

Use the built-in blade to remove excess length once these ties are secure.

The tail slots into the head to create a temporary loop to hold wires. Hook and unhook the loop to add additional wires before permanently cinching the tie.

The rounded, low-profile head keeps these ties from snagging and allows them to fit in tight spaces.

These ties are less likely to crack and break from dryness than regular cable ties.

Keep an assortment of cable ties on hand.

Reduce gaps between the cable tie and bundle—these ties have a smooth body that allows them to adjust to the exact size of the material.

Add push-in cable holder to this adapter to mount cable to DIN rail.

These mounts create space between a bundle and surface.

Bend cable around these holders and let tension keep the bundle in place. They are often used on wire harness boards.

A hard rubber coating and wire core helps these ties maintain their shape.

Bundle, close, and label bags and sacks.

Ties come on a spool for use in a twist tie machine.

The softest of our twist ties, they have a cushioned outer layer for bundling delicate materials.

These stretchy ties conform to irregularly shaped bundles to grip material tightly.

The ripple in the body prevents over tightening and allows for expansion to protect material that frequently changes size, such as heat cable.

The plastic coating on these ties adds an additional level of corrosion and abrasion resistance over other stainless steel cable ties.

Stamp or emboss these ties to identify material.

Secure and separate two bundles with the same tie.

Use this rubber tape to splice cable in high-voltage applications.

This traditional black cotton electrician's tape provides an abrasion-resistant shield for wrapping low-voltage splices.

Also known as mastic tape, this tape is thicker than other electrical tape to cushion, insulate, and seal out moisture and environmental contaminants in electrical connections.

At only 0.0025" thick, this tape combines conformability with durability and abrasion resistance.

This chemical-resistant tape has adhesive on both sides.

This puncture- and cut-resistant cotton tape is coated with a high-grade electrical-insulating varnish. Also known as cambric tape.

The adhesive on this conformable aluminum foil tape is electrically conductive for use on surfaces that can't be soldered. Use it to shield cables and electronic components from EMI (electromagnetic interference).

Use this tape to modify printed circuit boards, shield components, and prototype wiring-board layout and design.

A coating on this polyimide tape minimizes ESD (electrostatic discharge) when unwound from the roll and also during removal.

Use this tape to attach components to heat sinks and metal chassis walls in place of screws and other mechanical fasteners. It conducts heat away from sensitive electronics.

Use these convenient cut shapes to mask holes, fastener heads, and small areas while soldering.