Use this general purpose cable to supply power to equipment.

This cable can be stretched by about 40% and return to its original length, making it useful for applications where cable is in motion. It's often sewn into garments or used with equipment that must be worn.

A thick rubber insulation resists cuts and abrasion, so this cable can be pulled over rough surfaces without damaging the wires inside.

A braided bronze armor provides excellent protection against abrasion and other damage. The wires are tin-plated for corrosion resistance, and the insulation resists corrosive chemicals and salt water.

Rated to 12 volts DC, this cable is often used in low-voltage applications such as battery and vehicle wiring and radios. Also known as GPT cable.

Weather-resistant insulation makes this cable suitable for outdoor use and direct burial without conduit.

Reduce cable strain caused by equipment hanging from drop-down cable.

Often used in automated applications such as robotics and cable carriers, this cable withstands continuous motion without degrading data or signal transmission.

Use this cable without conduit in automated applications—it meets crush and impact requirements for exposed runs in cable carriers, and withstands continuous motion without degrading data or signal transmission.

In addition to handling continuous movement, this cable withstands twisting up to 450° without degrading data or signal transmission. It's often used in welding robots and rotary tables.

With a life span of more than 20 million high-speed flex cycles, this cable lasts twice as long as standard continuous-flex cable. The frequent motion will not degrade data or signal transmission.

Send data between computers, servers, and switches in an office or workstation.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. Use it to send data between computers, servers, and switches.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. It has an oil-resistant insulation to protect wires as the cable moves from duct to equipment or machinery.

Use this cable for complex and high-speed data and signal transmission.

Connect devices such as sensors, programmable logic controllers, and actuators to an automated network.

Also known as plenum cable, this cable has low-smoke insulation and can be used without conduit in ductwork and above a drop ceiling. Use it to transmit audio, video, and data signals.

Send signal and data to operate, measure, or regulate automated equipment such as conveyors and CNC machines.

This cable is used in variable-frequency drive motors. It has shielding to block signal interference caused by voltage fluctuations and current spikes.

Keep water from damaging wires—this cable has a layer of absorbent material that traps moisture before it reaches the internal wires. It sends signal and data to operate, measure, or regulate automated equipment.

This cable is approved for use in vertical shafts and large facilities with multiple levels. It's often used for low-current circuits such as intercoms and security systems.

Connect low-current circuits such as intercoms and security systems to a building's electrical system in single-level facilities.

The metal armor on this cable acts as conduit to protect the internal wires. It's often used along the exterior of walls to carry power to outlet boxes. Also known as MC cable.

This cable has an uninsulated ground wire that touches the protective metal armor so it can be used for bonding and grounding. It's often used along the exterior of walls to carry power to outlet boxes. Also known as AC cable.

Hook up thermostats, air-conditioning units, and other low-voltage equipment.

This cable withstands abrasion, oil, and the rough conditions found in welding applications.

Also known as hook-up wire, this wire is primarily used for wiring electrical panels, lighting, and plant floor equipment.

Keep spools of wire in multiple colors on hand.

More flexible than standard wire, this wire is often used for internal appliance wiring and machine tools. Also known as MTW wire.

Our most chemical-resistant wire—the PTFE insulation protects against most chemicals, solvents, and oil.

Use this wire in ovens, furnaces, and other electrical heating equipment where temperatures reach 480° F and higher.

Use this wire in high-voltage applications that require 10,000 volts DC or greater, such as in high-power signs and lasers.

Nearly half the diameter and up to 40% lighter than standard wire of the same gauge and voltage, this wire fits in tight spaces.

The shielding in this wire blocks signal interference from nearby equipment and devices. When pulled lengthwise, it extends 40% and then returns to its original length, so it's useful for high-vibration applications.

Connect batteries in vehicles and generators.

Keep spools of vehicle wire in multiple colors on hand.

Often used in automated applications such as robotics, this wire withstands continuous motion without degrading data or signal transmission.

The TPE insulation on this wire resists most chemicals, including oil and coolant, and withstands continuous motion.

Protected by an insulation that resists UV light and water, this wire is often used outdoors for lighting and generators.

Make connections in circuit boards with these short lengths of terminated wire.

This wire wraps around a post terminal on a circuit board to make an electrical connection, eliminating the need for soldering.

Connect devices such as computers, printers, and mobile devices.

With Kevlar-reinforced armor, these USB cords stand up to frequent use and bending better than standard USB cords.

Power up mobile devices and other electronics.

Screw these caps onto the socket end of wet-location USB cords. They maintain an IP67 rating when cords are not in use.

The insulation serves as a tough armor that protects these cords in high-traffic areas.

Often used in robotics, packaging, conveyors, and other applications with constant movement and high temperatures, these silicone rubber cords bend and flex at temperatures up to 325° F.

Stretch these cords out when you need extra length and their coiled design springs back when it’s not needed to make them smaller.

Connect computers, monitors, printers, and other devices with DB connections.

Display video from one source on two different monitors.

The shielding blocks signal interference from nearby equipment and devices.

To send high-speed data in tough, rugged environments, these cords have an M12 connector on one end that threads onto switches, sensors, and other devices prone to vibration. The other end has a traditional RJ45 plug that connects to Ethernet equipment, such as computers, IO modules, and programmable logic controllers (PLCs).

Send high-speed data between sensors, switches, or I/O modules with an M8 connection and programmable logic controllers (PLCs) and computers with a traditional RJ45 connection.

Often used in labs, storage facilities, and offices, the shielding blocks low to moderate signal interference from nearby equipment and devices. These cords have a flange on the socket end to mount them in a panel cutout.

The plugs on these cords pivot up to 90° in each direction to fit Ethernet jacks at awkward angles or in tight spots, such as behind equipment or in enclosures.

Send high-definition signals to monitors, TVs, and projectors.

Often used in automated applications such as robotics, these cords withstand continuous motion without degrading data transmission.

Connect audio to a single speaker, or extend the distance between stereo audio devices.

Make quick, secure connections between your development board and your system’s components, such as sensors and actuators.

Commonly used for movie, stage, and interior building lighting, these cords connect to equipment with five-pin XLR connections.

Replace the cords connecting your robot controller and teach pendant when they become worn, or switch them out for a different length.

Use these cords with computers, lab equipment, and office machines that have IEC connections.

Create a vibration-resistant connection—the socket on these cords securely locks onto any male receptacle and will not detach until manually unlocked.

Also known as hospital-grade cords, these cords have an extra-tight connection to prevent them from detaching. The plug is marked with a green dot.

Power multiple devices from one power source.

Designed for indoor applications, these cords are often used to power appliances.

All cords have a country-specific plug to power equipment from international outlets.

After a power failure, these cords must be manually reset, preventing unexpected equipment startup.

These cords work with any Milwaukee tool with a pin socket (Quik-Lok) connection.

FDA compliant for direct contact with food, these cords are safe to use with 12 mm proximity switches, valves, and power supplies in food, beverage, and pharmaceutical applications.