For a simplified keying system, these cam locks open with a hex key (not included).

Locks with a fixed latching distance are best when you know the precise distance you need. Since you won’t have to adjust the cam into position, they’re faster to install than locks with an adjustable latching distance. Those with offset or roller cams come with multiple cams to accommodate different latching distances.

Locks with an adjustable latching distance handle a wide range of latching distances, so they’re best for tasks when precise distances are unknown. Adjust the position of the cam before installing. They project further into the enclosure than those with a fixed latching distance.

Locks with a roller or protected cam rotate more smoothly than those with other straight and offset cams, making them easier to open and close. The cam won't scrape paint or metal chips off the frame that can damage items in the enclosure. The roller cam also compresses a bit to help minimize rattling from vibration.

Locks with a curved cam push closed without a tool or key. When pushed, the curved design lets the cam pivot slightly around the strike plate, securing the lock. To open them, turn the latch—the cam springs back so it's ready to be pushed closed again.

Stainless steel and plastic locks resist corrosion better than zinc locks. Plastic locks are the lightest in weight and do not conduct electricity. However, they’re easier to drill into and tamper with compared to metal locks.

Style B have a low profile, so they won’t catch on anything that passes by.

Locks with a pull tab give you a spot to grab to easily open doors and panels.

IP or NEMA rated locks have a gasket that keeps dust and water from getting in through the lock. IP65 rated locks seal out water from low-pressure washdowns.

EN 45545 rated locks meet flammability standards.

For technical drawings and 3-D models, click on a part number.

A gasket stops water from getting past these locks during high-pressure, high-temperature washdowns common in food processing plants. This helps you maintain a sealed enclosure's IP rating. Also known as quarter-turn locks, these locks rotate a cam 90° to secure your door or drawer. They lock with a hex key, so they’re great if you don’t want to keep a complicated keying system. Made of stainless steel, they resist corrosion, even when exposed to constant moisture. These locks come with multiple cams to accommodate different latching distances.

For technical drawings and 3-D models, click on a part number.

Spot when these locks are open with just a glance—a red indicator shows they're unlocked. Also known as compression cam locks, their cam seals more tightly against a door or drawer than a standard cam to reduce rattling from vibration. Using a hex key (sold separately), turn the head a quarter-turn to lock, then another quarter-turn to draw the cam firmly against your surface. Since they lock with a hex key, they’re great if you want a simple keying system. All come with multiple cams to accommodate different latching distances.

To help maintain a sealed enclosure's IP and NEMA rating, these locks have a gasket that stops water and dust from getting past the lock. Made of stainless steel, these locks resist corrosion, even in environments with constant moisture.

Locks with a fixed latching distance are best when you know the precise distance you need. Since you won’t have to adjust the cam into position, these are faster to install than those with an adjustable latching distance.

Locks with an adjustable latching distance are best for installations when precise latching distances are unknown. Adjust the position of the cam before you begin to install them. They project further into the enclosure than those with a fixed distance.

For technical drawings and 3-D models, click on a part number.

Trigger a light, alarm, or other device to signal your door is unlocked. These locks have a magnet on the cam that is detected by a sensor (required, sold separately). When you unlock the door, the magnet moves out of the sensing range, activating a switch that turns your device on or off. Lock the door to reset the switch. When choosing a lock, consider the magnet location that works best for your setup. Install your sensor next to the side of the cam where the magnet is located. You cannot use these locks near existing magnetic fields, since they could interfere with the sensor.

These locks open with a hex key (not included) for a simple keying system. Also known as quarter-turn locks, they have a cam that rotates 90° to close enclosure doors. You can adjust the cam’s latching distance, so these locks are best for jobs when precise distances are unknown. Adjust the position of the cam before installing.

A gasket stops dust and water from getting into your sealed enclosure through the lock. This helps you maintain the enclosure’s IP65 and NEMA 4 ratings.

Single pole, double throw (SPDT) sensors can be set to turn a device from off to on (normally open) or from on to off (normally closed).

Sensors with a light illuminate when the latch is open, so you can see the inside of your enclosure when you swing open the door.

For technical drawings and 3-D models, click on a part number.

A hex key (not included) opens and closes these cam locks, simplifying your keying system. Also known as quarter-turn locks, they have a cam that rotates 90° to lock cabinet doors and other enclosures. A gasket prevents water, dust, and dirt from getting into the enclosure through the lock. This helps you maintain your sealed enclosure’s IP65 and NEMA 4 ratings.

These locks come with three cams, so you can choose between three different latching distances. Each individual cam has a fixed latching distance. Since you won’t have to adjust the cams into position, these locks are faster to install than those that have cams with an adjustable latching distance. Locks with a roller cam rotate more smoothly than those with straight and offset cams, making them easier to open and close. The cam won’t scratch or flake enclosure surfaces to protect electronics inside from paint or metal chips.

For technical drawings and 3-D models, click on a part number.