Quick-Change Boring and Turning Cartridges
Limit downtime when you’re changing out cutting tools. Rather than removing and replacing an insert while your lathe is stopped, just swap out these cartridges and get right back to work. While one cartridge is in use, you can replace the insert in another, so a fresh cutting tool is always ready to go.
Pair these cartridges with a carbide insert and connect them to your lathe with either a quick-change cartridge holder or boring bar (each sold separately). Cartridge holders mount to quick-change lathe systems, also known as Capto, while boring bars mount with round shank toolholders. All components are coolant-through compatible. They have a hole that delivers coolant from your lathe onto the workpiece to minimize heat.
Back-boring cartridges pass through an existing hole to enlarge it from the back of the workpiece, rather than enlarging the hole as they enter. They are commonly used to make pipe fittings and hydraulic cylinders.
Use right-hand cartridges when the workpiece is rotating counterclockwise, or toward you. Use left-hand cartridges when the workpiece rotates clockwise, or away from you.
Cutting edge angle is also known as lead angle, entering angle, or KAPR.
For Insert | |||||||
|---|---|---|---|---|---|---|---|
| Cartridge OD | Min. Hole Dia. | O'all Lg. | Cutting Edge Angle | Inscribed Circle Dia. (IC) | Thick. | Each | |
Right Hand | |||||||
| 3/4" | 0.92" | 1 3/8" | 95° | 3/8" | 0.156" | 9181N15 | 0000000 |
| 1" | 1.185" | 1 5/8" | 95° | 3/8" | 0.156" | 9181N16 | 000000 |
| 1 1/4" | 1.465" | 2 1/8" | 95° | 1/2" | 0.187" | 9181N19 | 000000 |
| 1 1/2" | 1.73" | 2 1/2" | 95° | 1/2" | 0.187" | 9181N21 | 000000 |
| 1 3/4" | 2" | 2 7/8" | 95° | 1/2" | 0.187" | 9181N22 | 000000 |
| 2" | 2.4" | 3 3/8" | 95° | 1/2" | 0.187" | 9181N23 | 000000 |
Left Hand | |||||||
| 3/4" | 0.92" | 1 3/8" | 95° | 3/8" | 0.156" | 9181N11 | 000000 |
| 1" | 1.185" | 1 5/8" | 95° | 3/8" | 0.156" | 9181N12 | 000000 |
For Insert | |||||||
|---|---|---|---|---|---|---|---|
| Cartridge OD | Min. Hole Dia. | O'all Lg. | Cutting Edge Angle | Inscribed Circle Dia. (IC) | Thick. | Each | |
Right Hand | |||||||
| 3/4" | 1.05" | 1 3/8" | 95° | 3/8" | 0.156" | 9181N46 | 0000000 |
| 1" | 1.31" | 1 5/8" | 95° | 3/8" | 0.156" | 9181N47 | 000000 |
| 1 1/4" | 1.5" | 2 1/8" | 95° | 3/8" | 0.156" | 9181N48 | 000000 |
| 1 1/4" | 1.7" | 2 1/8" | 95° | 3/8" | 0.156" | 9181N49 | 000000 |
| 1 1/2" | 1.96" | 2 1/2" | 95° | 3/8" | 0.156" | 9181N51 | 000000 |
| 1 3/4" | 2.23" | 2 7/8" | 95° | 3/8" | 0.156" | 9181N52 | 000000 |
| 2" | 2.5" | 3 3/8" | 95° | 3/8" | 0.156" | 9181N53 | 000000 |
Left Hand | |||||||
| 3/4" | 1.05" | 1 3/8" | 95° | 3/8" | 0.156" | 9181N39 | 000000 |
| 1" | 1.31" | 1 5/8" | 95° | 3/8" | 0.156" | 9181N41 | 000000 |
| 1 1/4" | 1.7" | 2 1/8" | 95° | 3/8" | 0.156" | 9181N42 | 000000 |
| 1 1/2" | 1.96" | 2 1/2" | 95° | 3/8" | 0.156" | 9181N43 | 000000 |
| 1 3/4" | 2.23" | 2 7/8" | 95° | 3/8" | 0.156" | 9181N44 | 000000 |
| 2" | 2.5" | 3 3/8" | 95° | 3/8" | 0.156" | 9181N45 | 000000 |
O'all | ||||||
|---|---|---|---|---|---|---|
| For Cartridge OD | Manufacturer Equivalent No. | Usable Lg., mm | Dia. | Lg., mm | Each | |
| 3/4" | Capto C4, PSC-40 | 55 | 40 | 100 | 8935N11 | 0000000 |
| 3/4" | Capto C5, PSC-50 | 55 | 50 | 105 | 8935N14 | 000000 |
| 1" | Capto C4, PSC-40 | 80 | 40 | 125 | 8935N12 | 000000 |
| 1" | Capto C5, PSC-50 | 80 | 50 | 130 | 8935N15 | 000000 |
| 1 1/4" | Capto C4, PSC-40 | 95 | 40 | 140 | 8935N13 | 000000 |
| 1 1/4" | Capto C5, PSC-50 | 95 | 50 | 145 | 8935N16 | 000000 |
| 1 1/4" | Capto C6, PSC-63 | 98 | 63 | 158 | 8935N18 | 000000 |
| 1 1/2" | Capto C5, PSC-50 | 115 | 50 | 165 | 8935N17 | 000000 |
| 1 1/2" | Capto C6, PSC-63 | 118 | 63 | 178 | 8935N19 | 000000 |
| 2" | Capto C6, PSC-63 | 153 | 63 | 213 | 8935N21 | 000000 |
Quick-Change Boring and Turning Cartridge Holders
A pyramid-shaped shank makes these holders easier to switch in or out of your lathe than round-shank holders. They meet ISO 26623 for compatibility with quick-change systems. Quick-change systems are also known as Capto or PSC. Since these holders form a rigid connection with lathes, they’re often used for precision turning. Rather than removing and replacing an insert while your lathe is stopped, just swap out the cartridge (sold separately) and get right back to work. While one cartridge is in use, you can replace the insert on another, so a fresh cutting tool is always ready to go. Both holders and cartridges have a hole that passes coolant from your lathe onto the workpiece, minimizing heat. Pair the cartridges with carbide inserts.
Use right-hand cartridges when the workpiece is rotating counterclockwise, or toward you. Use left-hand cartridges when the workpiece rotates clockwise, or away from you.
Cutting edge angle is also known as lead angle, entering angle, or KAPR.
O'all | ||||||
|---|---|---|---|---|---|---|
| For Cartridge OD | Manufacturer Equivalent No. | Usable Lg., mm | Dia. | Lg., mm | Each | |
| 3/4" | Capto C4, PSC-40 | 55 | 40 | 100 | 8935N11 | 0000000 |
| 3/4" | Capto C5, PSC-50 | 55 | 50 | 105 | 8935N14 | 000000 |
| 1" | Capto C4, PSC-40 | 80 | 40 | 125 | 8935N12 | 000000 |
| 1" | Capto C5, PSC-50 | 80 | 50 | 130 | 8935N15 | 000000 |
| 1 1/4" | Capto C4, PSC-40 | 95 | 40 | 140 | 8935N13 | 000000 |
| 1 1/4" | Capto C5, PSC-50 | 95 | 50 | 145 | 8935N16 | 000000 |
| 1 1/4" | Capto C6, PSC-63 | 98 | 63 | 158 | 8935N18 | 000000 |
| 1 1/2" | Capto C5, PSC-50 | 115 | 50 | 165 | 8935N17 | 000000 |
| 1 1/2" | Capto C6, PSC-63 | 118 | 63 | 178 | 8935N19 | 000000 |
| 2" | Capto C6, PSC-63 | 153 | 63 | 213 | 8935N21 | 000000 |
For Insert | |||||||
|---|---|---|---|---|---|---|---|
| Cartridge OD | Min. Hole Dia. | O'all Lg. | Cutting Edge Angle | Inscribed Circle Dia. (IC) | Thick. | Each | |
Right Hand | |||||||
| 3/4" | 0.92" | 1 3/8" | 95° | 3/8" | 0.156" | 9181N15 | 0000000 |
| 1" | 1.185" | 1 5/8" | 95° | 3/8" | 0.156" | 9181N16 | 000000 |
| 1 1/4" | 1.465" | 2 1/8" | 95° | 1/2" | 0.187" | 9181N19 | 000000 |
| 1 1/2" | 1.73" | 2 1/2" | 95° | 1/2" | 0.187" | 9181N21 | 000000 |
| 2" | 2.4" | 3 3/8" | 95° | 1/2" | 0.187" | 9181N23 | 000000 |
Left Hand | |||||||
| 3/4" | 0.92" | 1 3/8" | 95° | 3/8" | 0.156" | 9181N11 | 000000 |
| 1" | 1.185" | 1 5/8" | 95° | 3/8" | 0.156" | 9181N12 | 000000 |
For Insert | |||||||
|---|---|---|---|---|---|---|---|
| Cartridge OD | Min. Hole Dia. | O'all Lg. | Cutting Edge Angle | Inscribed Circle Dia. (IC) | Thick. | Each | |
Right Hand | |||||||
| 3/4" | 1.05" | 1 3/8" | 95° | 3/8" | 0.156" | 9181N46 | 0000000 |
| 1" | 1.31" | 1 5/8" | 95° | 3/8" | 0.156" | 9181N47 | 000000 |
| 1 1/4" | 1.5" | 2 1/8" | 95° | 3/8" | 0.156" | 9181N48 | 000000 |
| 1 1/4" | 1.7" | 2 1/8" | 95° | 3/8" | 0.156" | 9181N49 | 000000 |
| 1 1/2" | 1.96" | 2 1/2" | 95° | 3/8" | 0.156" | 9181N51 | 000000 |
| 2" | 2.5" | 3 3/8" | 95° | 3/8" | 0.156" | 9181N53 | 000000 |
Left Hand | |||||||
| 3/4" | 1.05" | 1 3/8" | 95° | 3/8" | 0.156" | 9181N39 | 000000 |
| 1" | 1.31" | 1 5/8" | 95° | 3/8" | 0.156" | 9181N41 | 000000 |
| 1 1/4" | 1.7" | 2 1/8" | 95° | 3/8" | 0.156" | 9181N42 | 000000 |
| 1 1/2" | 1.96" | 2 1/2" | 95° | 3/8" | 0.156" | 9181N43 | 000000 |
| 2" | 2.5" | 3 3/8" | 95° | 3/8" | 0.156" | 9181N45 | 000000 |
Boring Bars with Quick-Change Connection
To limit downtime when you’re changing out cutting tools, these boring bars adapt standard lathes for use with quick-change cartridges (sold separately). Rather than removing and replacing an insert while your lathe is stopped, just swap out the cartridges and get right back to work. While one cartridge is in use, you can replace the insert on another, so a fresh cutting tool is always ready to go. Both bars and cartridges have a hole that passes coolant from your lathe onto the workpiece, minimizing heat. Pair the cartridges with carbide inserts.
Use right-hand cartridges when the workpiece is rotating counterclockwise, or toward you. Use left-hand cartridges when the workpiece rotates clockwise, or away from you.
Cutting edge angle is also known as lead angle, entering angle, or KAPR.
Boring Bars | Replacement Set Screws | |||||
|---|---|---|---|---|---|---|
| For Cartridge OD | Shank Dia. | O'all Lg. | Each | Each | ||
| 3/4" | 3/4" | 9 1/2" | 7944N11 | 0000000 | 7944N22 | 00000 |
| 1" | 1" | 11 1/2" | 7944N12 | 000000 | 7944N23 | 0000 |
| 1 1/4" | 1 1/4" | 14" | 7944N13 | 000000 | 7944N24 | 0000 |
| 1 1/2" | 1 1/2" | 14" | 7944N14 | 000000 | 7944N25 | 0000 |
| 1 3/4" | 1 3/4" | 16" | 7944N15 | 000000 | 7944N26 | 0000 |
| 2" | 2" | 10" | 7944N16 | 000000 | 7944N27 | 0000 |
| 2" | 2" | 20" | 7944N17 | 000000 | 7944N27 | 0000 |
| 2" | 2 1/2" | 12" | 7944N18 | 000000 | 7944N27 | 0000 |
| 2" | 2 1/2" | 24" | 7944N19 | 000000 | 7944N27 | 0000 |
| 2" | 3" | 28" | 7944N21 | 000000 | 7944N27 | 0000 |
For Insert | |||||||
|---|---|---|---|---|---|---|---|
| Cartridge OD | Min. Hole Dia. | O'all Lg. | Cutting Edge Angle | Inscribed Circle Dia. (IC) | Thick. | Each | |
Right Hand | |||||||
| 3/4" | 0.92" | 1 3/8" | 95° | 3/8" | 0.156" | 9181N15 | 0000000 |
| 1" | 1.185" | 1 5/8" | 95° | 3/8" | 0.156" | 9181N16 | 000000 |
| 1 1/4" | 1.465" | 2 1/8" | 95° | 1/2" | 0.187" | 9181N19 | 000000 |
| 1 1/2" | 1.73" | 2 1/2" | 95° | 1/2" | 0.187" | 9181N21 | 000000 |
| 1 3/4" | 2" | 2 7/8" | 95° | 1/2" | 0.187" | 9181N22 | 000000 |
| 2" | 2.4" | 3 3/8" | 95° | 1/2" | 0.187" | 9181N23 | 000000 |
Left Hand | |||||||
| 3/4" | 0.92" | 1 3/8" | 95° | 3/8" | 0.156" | 9181N11 | 000000 |
| 1" | 1.185" | 1 5/8" | 95° | 3/8" | 0.156" | 9181N12 | 000000 |
For Insert | |||||||
|---|---|---|---|---|---|---|---|
| Cartridge OD | Min. Hole Dia. | O'all Lg. | Cutting Edge Angle | Inscribed Circle Dia. (IC) | Thick. | Each | |
Right Hand | |||||||
| 3/4" | 1.05" | 1 3/8" | 95° | 3/8" | 0.156" | 9181N46 | 0000000 |
| 1" | 1.31" | 1 5/8" | 95° | 3/8" | 0.156" | 9181N47 | 000000 |
| 1 1/4" | 1.5" | 2 1/8" | 95° | 3/8" | 0.156" | 9181N48 | 000000 |
| 1 1/4" | 1.7" | 2 1/8" | 95° | 3/8" | 0.156" | 9181N49 | 000000 |
| 1 1/2" | 1.96" | 2 1/2" | 95° | 3/8" | 0.156" | 9181N51 | 000000 |
| 1 3/4" | 2.23" | 2 7/8" | 95° | 3/8" | 0.156" | 9181N52 | 000000 |
| 2" | 2.5" | 3 3/8" | 95° | 3/8" | 0.156" | 9181N53 | 000000 |
Left Hand | |||||||
| 3/4" | 1.05" | 1 3/8" | 95° | 3/8" | 0.156" | 9181N39 | 000000 |
| 1" | 1.31" | 1 5/8" | 95° | 3/8" | 0.156" | 9181N41 | 000000 |
| 1 1/4" | 1.7" | 2 1/8" | 95° | 3/8" | 0.156" | 9181N42 | 000000 |
| 1 1/2" | 1.96" | 2 1/2" | 95° | 3/8" | 0.156" | 9181N43 | 000000 |
| 1 3/4" | 2.23" | 2 7/8" | 95° | 3/8" | 0.156" | 9181N44 | 000000 |
| 2" | 2.5" | 3 3/8" | 95° | 3/8" | 0.156" | 9181N45 | 000000 |
Quick-Change Shank-Style Cartridge Holders for Cutoff,
Profiling, and Grooving Carbide Inserts with Two Cutting Edges
Slot these holders directly into your lathe tool post or mount in a tool holder. They pair with quick-change cartridges (sold separately) to limit downtime when you're changing cutting tools. Rather than removing and replacing an insert while your lathe is stopped, just swap out the cartridge and get right back to work. While one cartridge is in use, you can replace the insert in another, so a fresh cutting edge is always ready to go. Both holders and cartridges have a hole that passes coolant from your lathe onto the workpiece to minimize heat. The coolant also helps flush out chips, which prevents clogs and extends your tool life.
Choose a cartridge with the same cut type as your holder. You’ll also need a carbide insert—make sure the thickness of the insert fits the cartridge.
Cartridge Holders | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
Shank | Replacement Lock Screws | Replacement Coolant Seals | |||||||||
| Wd. | Ht. | Overall Lg. | Material | Finish | Hex Key Size | Each | Each | Each | |||
For Cutoff, External Grooving, External Profiling | |||||||||||
Right Hand—Straight | |||||||||||
| 3/4" | 3/4" | 5" | Steel | Nickel Plated | 0.197" | 8132N11 | 0000000 | 8132N19 | 00000 | 8132N21 | 00000 |
| 1" | 1" | 5 1/2" | Steel | Nickel Plated | 0.197" | 8132N12 | 000000 | 8132N19 | 0000 | 8132N21 | 0000 |
Right Hand—90° Angle | |||||||||||
| 3/4" | 3/4" | 4 1/4" | Steel | Nickel Plated | 0.197" | 8132N13 | 000000 | 8132N19 | 0000 | 8132N21 | 0000 |
| 1" | 1" | 4 3/4" | Steel | Nickel Plated | 0.197" | 8132N14 | 000000 | 8132N19 | 0000 | 8132N21 | 0000 |
For Face Grooving | |||||||||||
Left Hand—Straight | |||||||||||
| 3/4" | 3/4" | 5" | Steel | Nickel Plated | 0.197" | 8132N15 | 000000 | 8132N19 | 0000 | 8132N21 | 0000 |
| 1" | 1" | 5 1/2" | Steel | Nickel Plated | 0.197" | 8132N16 | 000000 | 8132N19 | 0000 | 8132N21 | 0000 |
Left Hand—90° Angle | |||||||||||
| 3/4" | 3/4" | 4 1/4" | Steel | Nickel Plated | 0.197" | 8132N17 | 000000 | 8132N19 | 0000 | 8132N21 | 0000 |
| 1" | 1" | 4 3/4" | Steel | Nickel Plated | 0.197" | 8132N18 | 000000 | 8132N19 | 0000 | 8132N21 | 0000 |
Cartridges for cutoff, external grooving, and external profiling can be used to slice off the end of your workpiece, carve channels, and create contours on the surface of your workpiece. As right-hand cartridges, they move from right to left, or toward the lathe chuck.
Overall | ||||||||
|---|---|---|---|---|---|---|---|---|
| For Insert Thick. | Max. Dp. of Cut | Lg. | Wd. | Ht. | Material | Finish | Each | |
Right Hand | ||||||||
| 0.079" | 0.24" | 1 5/8" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N11 | 0000000 |
| 0.079" | 0.47" | 1 3/4" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N12 | 000000 |
| 0.079" | 0.71" | 2" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N13 | 000000 |
| 0.118" | 0.47" | 1 3/4" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N14 | 000000 |
| 0.118" | 0.71" | 2" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N15 | 000000 |
| 0.118" | 1.06" | 2 1/4" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N16 | 000000 |
| 0.157" | 0.47" | 1 3/4" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N17 | 000000 |
| 0.157" | 0.71" | 2" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N18 | 000000 |
| 0.157" | 0.95" | 2 1/4" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N19 | 000000 |
| 0.157" | 1.18" | 2 1/2" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N21 | 000000 |
| 0.197" | 0.39" | 1 3/4" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N22 | 000000 |
| 0.197" | 0.59" | 1 7/8" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N23 | 000000 |
| 0.197" | 0.98" | 2 1/4" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N24 | 000000 |
| 0.197" | 1.58" | 2 7/8" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N25 | 000000 |
| 0.236" | 0.47" | 1 3/4" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N26 | 000000 |
| 0.236" | 0.71" | 2" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N27 | 000000 |
| 0.236" | 1.18" | 2 1/2" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N28 | 000000 |
| 0.236" | 1.89" | 3 1/4" | 5/8" | 1 3/4" | Steel | Nickel Plated | 7853N29 | 000000 |
Cartridges for face grooving can be used to machine circular grooves onto the end of your workpiece. As left-hand cartridges, they move from left to right, or away from the lathe chuck.
Overall | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| For Insert Thick. | Max. Dp. of Cut | Cutting Dia. | Lg. | Wd. | Ht. | Material | Finish | Each | |
Left Hand | |||||||||
| 0.118" | 0.47" | 7/8"-1 1/8" | 1 3/4" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N31 | 0000000 |
| 0.118" | 0.47" | 1 3/16"-1 7/16" | 1 3/4" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N32 | 000000 |
| 0.118" | 0.47" | 1 1/2"-1 7/8" | 1 3/4" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N33 | 000000 |
| 0.118" | 0.47" | 1 7/8"-2 3/8" | 1 3/4" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N34 | 000000 |
| 0.118" | 0.47" | 2 5/16"-2 3/8" | 1 3/4" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N35 | 000000 |
| 0.118" | 0.47" | 2 5/16"-3 7/8" | 1 3/4" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N36 | 000000 |
| 0.118" | 0.47" | 3 15/16"-7 13/16" | 1 3/4" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N37 | 000000 |
| 0.118" | 0.47" | 7 7/8"-11 3/4" | 1 3/4" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N38 | 000000 |
| 0.118" | 0.47" | 11 13/16" | 1 3/4" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N39 | 000000 |
| 0.118" | 0.71" | 2 5/16"-2 3/8" | 2" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N41 | 000000 |
| 0.118" | 0.71" | 2 5/16"-3 7/8" | 2" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N42 | 000000 |
| 0.118" | 0.71" | 3 15/16"-7 13/16" | 2" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N43 | 000000 |
| 0.118" | 0.71" | 7 7/8"-11 3/4" | 2" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N44 | 000000 |
| 0.118" | 0.71" | 11 13/16" | 2" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N45 | 000000 |
| 0.118" | 0.95" | 3 15/16"-7 13/16" | 2 1/4" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N46 | 000000 |
| 0.118" | 0.95" | 7 7/8"-11 3/4" | 2 1/4" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N47 | 000000 |
| 0.118" | 0.95" | 11 13/16" | 2 1/4" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N48 | 000000 |
| 0.236" | 0.51" | 2"-2 15/16" | 1 7/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N49 | 000000 |
| 0.236" | 0.51" | 3"-5 1/16" | 1 7/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N51 | 000000 |
| 0.236" | 0.51" | 5 1/8"-11 3/4" | 1 7/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N52 | 000000 |
| 0.236" | 0.51" | 11 13/16"-19 5/8" | 1 7/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N53 | 000000 |
| 0.236" | 0.51" | 19 3/4" | 1 7/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N54 | 000000 |
| 0.236" | 1.02" | 3"-5 1/16" | 2 3/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N55 | 000000 |
| 0.236" | 1.02" | 5 1/8"-11 3/4" | 2 3/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N56 | 000000 |
| 0.236" | 1.02" | 11 13/16"-19 5/8" | 2 3/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N57 | 000000 |
| 0.236" | 1.02" | 19 3/4" | 2 3/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N58 | 000000 |
| 0.236" | 1.54" | 3"-5 1/16" | 2 7/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N59 | 000000 |
| 0.236" | 1.54" | 5 1/8"-11 3/4" | 2 7/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N61 | 000000 |
| 0.236" | 1.54" | 11 13/16"-19 5/8" | 2 7/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N62 | 000000 |
| 0.236" | 1.54" | 19 3/4" | 2 7/8" | 5/8" | 1 1/2" | Steel | Nickel Plated | 7853N63 | 000000 |