We will reply to your message within an hour.
Drill holes of any size and etch your own circuit board design into copper-clad boards.
Also known as breadboards or proto-boards, these boards have 0.042” dia. holes with solder pads.
Also known as solderless breadboards. A contact point inside each hole creates a connection without soldering.
Combine the functionality of a PC with the flexibility of a development board’s digital inputs and outputs.
Prototype electronics and build simple automation systems with the configurable inputs and outputs on these boards.
Keep a development board and a breadboard in one handy spot for prototyping.
These boards are smaller than other development boards, so they save space in your setup—while still having the configurable inputs and outputs that make them good for rapid prototyping.
Program mini development boards and other custom circuit boards with these modules.
Use these headers to make quick, temporary connections to development boards and other circuit boards when prototyping.
Also known as thermal pads and thermal interface pads, these heat-dissipating pads pull heat away from electronic components.
Limit the electrical current that flows through your circuit, adjust signal levels, and divide voltages.
Terminals fit into 0.042" dia. holes so you can make connections to a circuit board.
Use diodes and rectifiers to convert current from AC to DC. Transistors allow you to switch or amplify electronic signals.
Capacitors store electrical energy and release it all at once, similar to a camera flash.
Holders have snap-on or screw-on covers to fully enclose and protect batteries.
Combine the functionality of a PLC and the accessibility of a development board. Built around a Raspberry Pi and an Arduino-enabled microcontroller, these controllers use open-source software to make programming and troubleshooting convenient.
Often found on older radio transmitters and circuit boards, these switches configure instructions for electronic devices.
Also known as tactile switches, these are small enough to fit inside a computer keyboard.
Sized for 4 mm or 6 mm panel cutouts, these switches are often used with circuit boards to control electronics.
Solder these relays directly to printed circuit boards using their solder pin terminals.
Make quick, secure connections between your development board and your system’s components, such as sensors and actuators.
Make connections in circuit boards with these short lengths of terminated wire.
This wire wraps around a post terminal on a circuit board to make an electrical connection, eliminating the need for soldering.
Use this tool to tightly wrap wire around a post terminal, or to unwind it.
Assortments include wire in multiple lengths and colors.
Light up small and hard-to-reach areas.
These connectors allow you to connect USB devices to a circuit board.
Add ix Industrial connections to printed circuit boards (PCBs).
Audio/video HDMI connectors and cords are rated IP67 when mated.
Solder the pins on these blocks directly to your circuit board.
Some of the smallest signal/power connectors we offer, these connectors fit in tight spaces and are often used in electronics.
Add RJ45 connectors to circuit boards.
Add a D-sub connection to a printed circuit board (PCB). These connectors are often used in applications involving monitoring, control, and communication.
Often used to prototype or replace damaged connections, these connectors allow you to access and connect to individual USB pins.
Wire terminals allow you to connect these bulbs to a power source through a panel.
Scan RFID cards when prototyping systems for item tracking, conveyor sorting, and facility access.
Protect up to twenty-four 3" × 3" to 12" × 12" circuit boards from static electricity.
Protect development boards from dust, water, and debris by mounting them to DIN rails inside control cabinets.
Glue these gauges onto a structure to measure strain in a single direction.
Communicate between a development board and other components, such as sensors and actuators, that use digital signals at a different voltage.
Measure your equipment’s pressure and send the data directly to a development board or single-board computer. Also known as transducers, these transmitters convert pressure into an electrical I2C signal and transmit it to your board.
Includes technical, machinery, and electrical code handbooks as well as occupational safety manuals and field reference books.
Cool down enclosures, laser and optical equipment, and other small devices to maintain their ideal temperature.