Use these lights in tight spaces in place of a tower. They emit three colors from a single lens. Color is selectable. Lights have an LED bulb that provides years of maintenance-free operation. Rated NEMA 4X for protection from corrosion and washdowns.

Mount these lights horizontally or vertically in places where a tower will not fit. The LED bulbs provide years of maintenance-free operation. Lights meet IP54 for use in environments with splashing water.

Give a signal with the push of a button. These lights have a control box with a button for activating each of the three light modules. The LED bulbs provide years of maintenance-free operation.The light modules meet IP54 and the control box meets IP20. They cannot be sold to the regions listed due to local energy efficiency requirements.

Mount the light by bolting the included bracket to a surface (fasteners not included) or clamping it over a surface such as an office partition or workstation. You can adjust the height of the light by using either the included 3 1/2” or 11 3/8” mounting poles.

Mount the control box using the included tape with adhesive on both sides. It connects to the light via a 4-ft. connecting cable.

This light emits three colors from a single lens and can be mounted in tight spaces where a tower will not fit. Color is selectable. Light has a quick-connect M12 plug that makes it easy to hook up and configure and an LED bulb for years of maintenance-free operation.

Use the DIN-rail-mount bracket (sold separately) to mount the light at any angle on a DIN rail.

The quick-connect four-pole M12 plug on these lights makes them easy to hook up and configure. Mount the male thread on the bottom of the light through a hole and then secure using the included nut and sealing gasket. Lights have LED bulbs for years of maintenance-free operation. They meet IP65 for protection from washdowns.

Lights have an LED bulb for years of maintenance-free operation. They help meet OSHA standards.

Communicate a status at a glance by wiring these strip lights to change color when a part is malfunctioning inside your enclosure. They connect to sensors and switches in your system. LED bulbs are long-lasting and don’t get hot, which protects your electronics. They have a low-profile design for use in tight spaces.

Strip lights with built-in white/red LED bulbs have a white light, so they can be used as a task light to see the components you're working on.

Strip lights with an M12 plug require a power cable (sold separately) to hardwire the lights to your power source.

Use a magnetic mounting bracket (sold separately) to install lights in steel enclosures without drilling holes through the enclosure and risking contaminants like water and dust.

Connector cables (sold separately) link multiple strip lights together from one power source, so you can brighten large enclosures. At 12V DC, connect up to 6 strip lights; at 24V DC, connect up to 16 strip lights.

These thin, flexible lights wrap around equipment, hide under cabinets, and squeeze into tight spaces—all you need is an outlet. Just peel and stick to attach them to any smooth surface. They’re easier to install than hardwired tape lights, but they’re not as bright. All come with a controller to turn them on or off and adjust the brightness and light appearance. You can also cut them to size.

Tape lights with any-color LEDs can display the full spectrum of colors and any temperature of white. Use them to illuminate signs, brighten displays, or mark zones in your facility. They’re more flexible than tape lights with only white LEDs, so you can bend them around corners without adding a connecting cable. You can connect two 20 ft. long lights to create a longer light.

Bend these flexible lights around corners or squeeze them into spaces where bulky fixtures won’t fit. They’re brighter than plug-in tape lights, so you can use them for inspections and other detailed work. They’re also a great choice to extend the life of your fluorescent or incandescent fixtures with energy-efficient LEDs. They have a higher CRI (color rendering index) than most other lights, so they illuminate subtle color differences. Each LED is inspected to make sure there are no visible differences in temperature and brightness, so you can combine multiple strips within the same space. Install them on any smooth surface—just peel and stick.

You’ll need a driver to power these lights. Customize your setup: join multiple lights together, use connectors to bridge gaps between stairs or shelves, or add channels to diffuse light within your space (all sold separately).

Note: To shorten a light, cut it at the marked intervals only. Cutting outside these marks can damage the circuit and create dead zones.

Know your machine’s status at a glance—green for running, red for stopped, yellow for standby. Using your programmable logic controller (PLC), you can adjust the brightness of these lights and mix red, green, and blue light to achieve thousands of colors. They shine a bright white by default to illuminate your production line.

With a smooth, shatterproof lens, these lights have no crevices where debris can accumulate. Their stainless steel connectors, plastic lens, and mounting brackets resist acids, alkalis, and other chemicals commonly used in food environment washdowns. All are IP rated to seal out dust and withstand high-pressure, high-temperature sprays required for sanitizing.

Use the included hardware to install them in your machine. They require a 5-pole micro M12 socket (sold separately) to connect to your PLC.