Get dry compressed air in high-pressure systems—these dryers have a maximum pressure rating of 300 psi. Once aftercoolers and separators have removed the bulk of the water, they remove any remaining moisture in your air line. Install after an oil filter to protect the desiccant. They have a sight glass so you can see inside the bowl to monitor contents.

Desiccant (sold separately) is required to remove moisture from air. To reuse saturated desiccant, heat it at its reactivation temperature until it returns to its dry color.

For use with Norgren modular compressed air systems, once aftercoolers and separators have removed the bulk of the water, use one of these desiccant-filled dryers to remove any remaining moisture in your air line. Install after an oil filter to protect the desiccant. They have a clear bowl so you can see inside to monitor contents. To reuse saturated desiccant, heat it at its reactivation temperature until it returns to its dry color.

Use a joiner clamp (sold separately) to connect your dryer to another Norgren modular component.

End block sets (sold separately) allow you to swap out filter/regulator/lubricator components without unthreading your air line connections. The blocks remain connected to your pipe while you replace components between them.

With a clear polycarbonate bowl that’s visible from all angles and silica gel desiccant that changes from blue to pink, it’s easy to see when it’s time to change the cartridge on these dryer/filters and dryer/filter/regulators. In addition to water, they remove compressor oil and particles, preventing damage to air-powered tools and equipment. Unlike some desiccant dryers, they don't require a filter to protect the desiccant. Both the dryer and filter are in the same cartridge, saving space and reducing downtime when they need to be changed. Install them after aftercoolers and separators, which remove the bulk of the moisture.

Dryer/filters and dryer/filter/regulators with a shut-off valve can stop the flow of air when the units are not in use to extend the life of the desiccant.

Dryer/filter/regulators have a regulator to monitor and adjust the flow of air.

These dryer/filters have a clay desiccant that removes moisture, oil, and particles, so there’s no need to install a separate filter and dryer. Once aftercoolers and separators have removed the bulk of the water, they remove any remaining moisture in your air line. Dryer/filters have a clear bowl or sight glass that allow you to see inside to monitor the contents. When the desiccant becomes saturated, it changes color to indicate that it should be replaced.

Dryer/filters with an aluminum bowl stand up to synthetic compressor lubricants and solvents better than dyers with an acrylic plastic bowl can.

Dryer/filters with a polyurethane bowl have excellent resistance to synthetic compressor lubricants, solvents, acids, and other chemicals.

Remove bulk water vapor from your compressed air line by refrigerating the air. These dryers have a timer-activated drain valve that opens automatically to discharge condensate. Install them in your air line after the compressor and separator.

Non-cycling dryers run continuously to dry compressed air, so they’re best for applications with a constant need for dry air.

Cycling dryers adjust their cooling level based on your compressed air system’s needs. While they require more maintenance than non-cycling dryers, they’re more energy efficient. They’re best suited for applications with varying air demands.

These all-in-one dryers with filters eliminate the need for individual dryers and filters. They cool air through refrigeration to condense water vapor for removal. Because they are non-cycling and run continuously, they are best for applications that need constant dry air. A float-operated drain valve opens automatically when the bowl begins to fill. After water removal, a heat exchanger raises the outlet air temperature to prevent condensation on downstream piping. The built-in display lets you monitor and adjust the dew point of the compressed air. Be sure to install in your air line after the compressor and separator.

Prevent equipment damage caused by moisture. The first step in water removal, these separators remove the water that accumulates as compressed air cools. They have a float-operated drain valve that automatically opens when the bowl begins to fill. Install in your air line after compressors and aftercoolers.

Separators with a sight glass allow you to see inside the bowl to monitor its contents.

Let these separators handle the dirty work of condensate disposal. When water condenses in a compressed air system, it picks up oil from the compressor, making disposal a challenge. These separators use two-stage filtration to cut oil content to under five parts per million. The primary filter clears out dirt, sludge, and most of the oil. The secondary filter handles the rest—including synthetic lubricants that other systems struggle with. A service sticker shows when it’s time to replace the filters. Check local codes for disposal requirements.

A sampling port lets you test water without disconnecting outlet piping. Connect up to four compressed air components—such as aftercoolers, separators, or drain valves—to the four inlets.

Replacement kits include both filter bags and a fresh service sticker.

In addition to removing large amounts of water, these separators also remove particles and oil droplets. Place them after your compressor and aftercooler, or at the point of use in applications that don't require an aftercooler. They have an automatic drain to discharge the moisture.

Separators with an aluminum bowl are stronger than those with a polycarbonate plastic bowl—they won’t crack or shatter if dropped.