These separators have higher flow rates compared to our other compressed air separators. Prevent equipment damage and wear caused by moisture in your compressed air supply. The first step in water removal, use one of these separators to remove the large amount of water created as compressed air cools.

Let these separators handle the dirty work of condensate disposal. These separators use two-stage filtration to cut oil content to under five parts per million.

Remove oil from the condensate in your air line, so you can properly dispose of it. These bags replace old ones in your compressed air condensate separators.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air. Joiner clamps connect these air filters into your Parker setup.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Get two stages of filtration—the first stage removes most particles and water droplets; the second captures any remaining particles and water droplets down to 5 microns.

A polyurethane bowl provides good chemical resistance for use with synthetic compressor oils and cleaning fluids.

Remove particles from large volumes of compressed air without causing restriction or drops in pressure.

Made of corrosion-resistant material, these filters withstand harsh environments where standard filters can break down and fail.

Quickly install these filters on your air line—no pipe nipples or joiner clamps required. Their push-to-connect fittings create tight seals around tubing.

Two-stage filtration is like getting two filters in one—the first stage removes large particles, while the second removes fine particles.

No need to buy and service two filters—these filters have a single element that removes both oil and particles.

Replace the filter element in your Norgren modular compressed air filter to trap solid particles and water droplets.

Replace the filter element in your ARO modular compressed air filter to trap solid particles and water droplets.

Replace the filter element in your Festo modular compressed air filter to trap solid particles and water droplets.

Produce clean air for instrumentation and other applications, such as food or medical device manufacturing.

Remove bacteria, viruses, moisture, and other particles from compressed air and gases used in food, pharmaceutical, biotech, and electronics applications.

Prevent damage to air-powered tools and equipment—these dryers remove water, compressor oil, and particles from your air supply. The dryer and oil filter share the same cartridge to save space and reduce downtime when changing them.

For an uninterrupted supply of clean, dry compressed air, these dryers have two desiccant towers. While desiccant in one tower absorbs moisture, the desiccant in the other is drying out, then they switch automatically.

For use with Norgren modular compressed air systems, once aftercoolers and separators have removed the bulk of the water, use one of these desiccant-filled dryers to remove any remaining moisture in your air line.

Install these dryers just before air-powered tools as final protection from water and particles and throw them away when you’re done.

These all-in-one dryers with filters eliminate the need for individual dryers and filters. They cool air through refrigeration to condense water vapor for removal.

Stop moisture from reaching tools and equipment. These dryers have a polypropylene filter element that expands when wet, shutting off airflow until the element is replaced.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

These filter/regulator combinations come as one convenient unit that cleans the air as it regulates pressure.

A filter and regulator joined top-to-bottom, these filter/regulators provide clean, compressed air at the pressure you need. They connect to other Festo units of these same series with joiner clamps—even if the pipe sizes are slightly different—so you can customize your air preparation system.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

Built to resist corrosion, these filter/regulators withstand harsh environments that would cause standard filter/regulators to break down and fail.

A clear polyurethane bowl makes these filter/regulators chemical resistant for use with synthetic compressor oils and cleaning fluids and allows you to see inside to monitor contents.

Assembled, inspected, and packaged in a clean environment, these filter/regulators come sealed in antistatic double bags.

Designed for quick installation on your air line, these filter/regulators don’t require pipe nipples or joiner clamps. Their push-to-connect fittings create airtight seals on tubing.

Minimize the footprint of your air preparation system with these all-in-one manifolds—they include a filter, a regulator, a slow-start valve, and a safety lockout valve.

A Wilkerson filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Norgren filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Parker filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

No need for thread adapters—these filter/regulator/lubricators have an NPT inlet and a BSPP outlet.

With one outlet port before the lubricator and one after, these filter/regulator/lubricators work in systems that require lubrication in some lines but not in others.

Distribute compressed air to multiple locations from a single source.