In addition to removing large amounts of water, these separators also remove particles and oil droplets. Place them after your compressor and aftercooler, or at the point of use in applications that don't require an aftercooler.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air. Joiner clamps connect these air filters into your Parker setup.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Extend the service life of air-powered tools and equipment by removing particles and water droplets from compressed air.

Get two stages of filtration—the first stage removes most particles and water droplets; the second captures any remaining particles and water droplets down to 5 microns.

Discharge up to 300 gallons of water and particles per hour—these filters handle compressed air that’s high in moisture content.

Use these filters where high water and dirt removal is needed—they have a two-layer filter element made of stainless steel wire mesh and cotton/polyester packing.

No need to buy and service two filters—these filters have a single element that removes both oil and particles.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment. Joiner clamps connect these air filters into your Norgren setup.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Built to resist corrosion, these filters can withstand harsh environments that would cause standard filters to break down and fail.

With an activated carbon element, these filters remove all traces of oil vapor from your air lines, including odor. Joiner clamps connect these air filters into your Norgren setup.

Use these filters in applications where high-quality air is critical. They remove particles down to 0.003 microns, eliminating small traces of oil vapor and its associated odor.

Housing and bowl are 304 stainless steel for good corrosion resistance in damp environments.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

Connect these filter/regulators to other Aventics units of the same series with joiner clamps to customize your air preparation system. A filter and regulator joined top-to-bottom, they provide clean, compressed air at the pressure you need.

These filter/regulator combinations come as one convenient unit that cleans the air as it regulates pressure.

No need for thread adapters—these filter/regulators have an NPT inlet and a BSPP outlet.

Assembled, inspected, and packaged in a clean environment, these filter/regulators come sealed in antistatic double bags.

Built to resist corrosion, these filter/regulators withstand harsh environments that would cause standard filter/regulators to break down and fail.

Minimize the footprint of your air preparation system with these all-in-one manifolds—they include a filter, a regulator, a slow-start valve, and a safety lockout valve.

A filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Parker filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Wilkerson filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

With one outlet port before the lubricator and one after, these filter/regulator/lubricators work in systems that require lubrication in some lines but not in others.

With a polyurethane bowl and housing, these dryers resist synthetic compressor lubricants, solvents, acids, and other chemicals in your compressed air line. They have a clear bowl so you can monitor contents and the desiccant, which changes color when it needs to be replaced.

Once aftercoolers and separators have removed the bulk of the water, use these dryers to remove any remaining moisture in your air line.

Remove water and compressor oil from your air line to prevent damage to air-powered tools and equipment. The dryer and filter share the same cartridge to save space and reduce downtime when changing them.

These all-in-one dryers with filters eliminate the need for individual dryers and filters. They cool air through refrigeration to condense water vapor for removal.