We will reply to your message within an hour.
Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.
A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.
Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.
Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.
Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.
Clip these hangers onto the side of threaded rod. Unlike other threaded-rod-mount hangers, you can use more than one hanger on the same rod to organize multiple lines of pipe, tubing, and conduit.
These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.
Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.
Connect these hangers to organize multiple lines of pipe, tubing, and conduit. The tight-fitting, santoprene body reduces vibration and prevents corrosion caused by metal-to-metal contact.
These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.
Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.
These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.
Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.
Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.
Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.
A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.
Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.
Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.
A versatile solution for temporary hanging of pipe and tubing at work sites as well as anywhere welding and fastening are not possible. Feed material through the strap, then use the D-rings to adjust the hanging height.
Cut as much strap as you need to hang duct, pipe, and other materials.
Use these close-fitting hangers for a more rigid hold around material than when using straps alone.
Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.
These clamps have a fixed hanger for rigid connections.
Reduce noise caused by HVAC systems. These sturdy rubber supports isolate vibration caused by heat pumps and air conditioning units, resulting in a quieter facility. When used on roofs, they also keep components above puddled water, which can cause damage.
These U-shaped supports allows access to pipe and conduit after installation.
Bolt directly to a pipe flange to suspend a run of pipe above the ground.
Adjust supports to the exact height you need to route pipe, conduit, and tubing through strut-mount routing clamps and hangers.
For a secure hold on pipe and conduit suspended above the ground, these supports have a cushioned clamp provides a 360° grip while reducing vibration.
Support lines that expand and contract. The roller on these supports compensates for movement in your line from changing temperatures.
Attach these supports onto metal stud knockouts to route cable, conduit, and tubing through metal studs.
Mount these brackets between two studs to support copper tubing for sink faucets and other water supply fixtures.
Suspend and route flat-bottomed objects such as strut channel and small duct.
A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to disassemble it.
Also known as muffler clamps, these U-bolts have a rounded mounting plate that fully surrounds pipe, conduit, and tubing for a secure fit.
These fiberglass-reinforced polyurethane U-bolts have no metal parts, so they won't conduct electricity or cause metal-to-metal corrosion.
Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.
Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.
Mount these general purpose U-bolts into an existing bracket, or combine with a mounting plate for a secure hold at the mounting surface.
A mounting plate provides a more secure hold at the mounting surface.
Join pieces of conduit.
Attach conduit to a knockout in an outlet box or enclosure.
Also known as conduit bodies, these ports provide access to wire and cable inside PVC conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.
Connect different sizes and genders of conduit.
Join different sizes of conduit.
Connect to the end of conduit or a fitting to protect wires from abrasion when being pulled.
Reduce the knockout size in an outlet box or enclosure so you can attach a different size of conduit to it.
Ground conduit by running a ground wire through the attached lug.
Seal out moisture while reducing the knockout size in an outlet box or enclosure so you can attach a different size of conduit to it.
Connect different sizes of conduit.
Also known as conduit bodies, these ports provide access to wire and cable inside thick-wall (rigid) metal conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.
Also known as conduit bodies, these ports provide access to wire and cable inside metal conduit for pulling, splicing, and maintenance. They are also used to change the direction of a run.
Create a weatherproof entry point into a building for service cables and telephone lines—these kits have all the supplies you need.
Create a connection point to route overhead service wire and cable from utility poles to electrical meters, bringing power to buildings.
Slide these grommets into conduit ends to protect wire and cable from abrasion when being pulled.
Also known as antishort bushings, these grommets slide into the ends of conduit and armored cable to protect wire and cable from sharp edges.
Attach conduit and armored cable to a knockout in an outlet box or enclosure.
Preventing wear and cracks, these grommets shield the sections of your conduit that rub and bang against nearby components.
Hold flexible plastic conduit in place along walls and machines.
These adapters provide electromagnetic interference (EMI) protection when connecting shielded flexible plastic conduit to a knockout in an outlet box or enclosure.
These fittings seal out liquids when connecting liquid-tight flexible metal conduit to a knockout in an outlet box or enclosure.
Secure threaded metal conduit fittings to a knockout in an outlet box or enclosure.
Secure threaded plastic conduit fittings to a knockout in an outlet box or enclosure.
These fittings seal out liquid when used with continuous-flex liquid-tight plastic conduit.
One end twists into a piece of conduit for a quick connection; the other end attaches to a knockout in an outlet box or enclosure.
Transition between types of conduit.
Transition between conduit sizes and types.
Use a blower or vacuum to insert this lightweight threading line into conduit or raceway, and attach it to your pulling rope to guide the rope.
Each set includes six grips for pulling one or more cables through conduit.
Pull one or more cables through conduit.
Adapt metric, NPT, and PG conduit and cord grip threads to match knockout threads.
To avoid gouging and marring your pipe while making adjustments, these collars have flats where you can grab and rotate the pipe with a wrench. They're sized precisely for a tight fit around pipe, so they're often used to support pipe passing through floors and walls.
Sized to fit snugly around pipe, these collars have flats so you can turn the collar and your pipe using a standard wrench.
Often used in corrosive environments to support pipe passing through walls and floors, these collars are 303 stainless steel and sized specifically for a tight fit around pipe.
Sized to fit snugly around pipe, these collars are often used to support pipe passing through floors and walls.
Already mounted in a conduit box, these connection strips save you the effort of modifying a panel for installation.
Support and protect conduit by mounting it to strut channel.
Attach cable, pipe, tubing, and other items to your strut channel.
Attach strut channel at any point on a threaded rod without taking apart your assembly.
Slip these hangers onto the lip of top-opening strut channel to attach chain, wire rope, pipe, and threaded rod.
For quick mounting of components, these hangers snap into strut channels for a strong hold and easy repositioning.
Bend more than one size of tubing without adjusting the bending head.
Heat PVC conduit and pipe, then manually bend it to your desired angle.
Choose these benders for short‐radius conduit bending.
When you're working with exposed conduit, these benders make offset bends so your conduit matches knockout holes in electrical boxes.
Powerful enough to bend conduit and pipe to the angle you need, these are for use on Schedule 40 pipe.
Make on-the-fly bends in Schedule 40 PVC conduit and pipe without the risk of kinks or cracks. Lightweight and flexible, these benders are easy to keep on hand for occasional use and last-minute adjustments.
Follow the easy-to-read markings to bend conduit to the angle you need.