For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Bolt or weld these rails to the mounting surface, then attach clamps with a rail nut.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.

Organize multiple lines of pipe, tubing, or hose with a single clamp. They are polyethylene for good chemical and UV resistance.

Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.

Flexible grooves inside these polypropylene clamps allow material to expand and contract. Clamps are moisture and chemical resistant.

A cushion covering the clamp reduces vibration and wear from clamp edges. Clamps surround lines of pipe, tubing, and conduit completely while holding them close to the mounting surface.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

Use these clamps to route insulated pipe through floors. They have a plastic insert that creates a seal around the pipe's insulation to prevent the pipe from sweating, which can cause mold and corrosion.

Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.

Suspend and route flat-bottomed objects such as strut channel and small duct.

Reduce vibration and noise in your lines—a plastic cushion tightly grips pipe, tubing, and conduit to prevent movement. Nylon-insert locknuts grip the thread to resist loosening.

Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.

Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.

A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.

Clip these hangers onto the side of threaded rod. Unlike other threaded-rod-mount hangers, you can use more than one hanger on the same rod to organize multiple lines of pipe, tubing, and conduit.

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.

Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.

Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.

Suspend material at any angle from the beam. Clamps have a fixed jaw that secures to the beam and a hanger that swivels 360° to position material and accommodate for misalignment.

Attach these light duty hangers to beams and other structural elements. They include a stiff wire for supporting ceilings, lighting fixtures, and other lightweight material.

For a secure hold on pipe and conduit suspended above the ground, these supports have a cushioned clamp provides a 360° grip while reducing vibration.

Bolt directly to a pipe flange to suspend a run of pipe above the ground.

Adjust supports to the exact height you need to route pipe, conduit, and tubing through strut-mount routing clamps and hangers.

Bundle cables outdoors with these ties that withstand exposure to UV rays and water.

These ties stretch to hold material tightly without slipping.

These cable ties are easy to yank apart or cinch shut, even when wearing gloves—a textured tab on the end gives you a good grip.

These ties are flexible, reusable, and adjustable for delicate bundles or bundles that frequently change in size.

Flexible enough for small bundles, these ties are often used for electronics.

Able to fit small bundles, these thin ties are more flexible than other ties.

Create a cable tie with a buckle—no sewing required.

Stick these ties to any smooth, clean surface.

Quickly attach and detach a bundle.

Keep a set of these differently sized cable ties on hand to use when you need them. They're flexible, reusable, adjustable.

These cable ties come with a material certificate with traceable lot number and product shelf life.

These cable ties have a finely ribbed body and a metal-toothed head that allows them to adjust to the exact size of the material without slipping.

The head of these cable ties is contoured to fit against pipe, tubing, and other round material for a tight fit.

Create custom-length cable ties for large bundles and heavy materials.

Whether you plan to change the bundle size or need a temporary hold, these ties have a release tab for removal and reuse.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

The tail slots into the head to create a temporary loop to hold wires. Hook and unhook the loop to add additional wires before permanently cinching the tie.

For use in environments subjected to chemicals, these ties withstand the most corrosive conditions.

The rounded, low-profile head keeps these ties from snagging and allows them to fit in tight spaces.

A foam padded back combined with an extra-wide body protects sensitive bundles, such as fiber optic cable.

Secure and separate parallel bundles with the same tie.

Reduce gaps between the cable tie and bundle—these ties have a smooth body that allows them to adjust to the exact size of the material.

Keep an assortment of cable ties on hand.

A foam padded back combined with an extra-wide body protects sensitive bundles, such as fiber optic cable.

Add push-in cable holder to this adapter to mount cable to DIN rail.

These mounts create space between a bundle and surface.

Bend cable around these holders and let tension keep the bundle in place. They are often used on wire harness boards.

A hard rubber coating and wire core helps these ties maintain their shape.

Ties come on a spool for use in a twist tie machine.

The softest of our twist ties, they have a cushioned outer layer for bundling delicate materials.