Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

Organize multiple lines of pipe, tubing, or hose with a single clamp. They are polyethylene for good chemical and UV resistance.

Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Route pipe, tubing, and conduit across strut channel.

Hold pipe, tubing, and conduit away from strut channel.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Temporarily route material across duct, racks, machinery, and other ferrous surfaces. Clamps fit tightly around pressurized lines in hydraulic systems to lessen vibration. Rubber cushions reduce wear from clamp edges and protect lines from corrosion caused by metal-to-metal contact.

For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Support vertical pipes passing through floors.

Route bundles of wire and cable through a single hook. A wide opening allows access for installation, adjustment, and removal.

Also known as bridle rings, routing rings have an open-eye design that allows you to quickly install wire and cable.

Mount these ringbolts into a threaded hole, or use the nut for through-hole mounting. The pivoting ring allows material to move freely.

Hang cable and other flexible material beneath wire to prevent it from sagging and swaying. To install, hook the two ends of the ring around the wire—no fasteners required.

Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.

These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.

For a strong, secure connection, mount these hangers by welding them to a rod.

Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.

Reduce vibration and prevent metal-to-metal corrosion on flat-bottomed objects such as strut channel and small duct.

Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

These fiberglass-reinforced polyurethane U-bolts have no metal parts, so they won't conduct electricity or cause metal-to-metal corrosion.

Mount to a surface to secure and route cable.

These mounts create space between a bundle and surface.

Secure multiple cable bundles with a single holder.

Add a hook and loop cable tie to these mounts to secure a bundle.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

Flexible enough for small bundles, these ties are often used for electronics.

These cable ties are easy to yank apart or cinch shut, even when wearing gloves—a textured tab on the end gives you a good grip.

Create custom-length ties from a roll with hook on one side and loop on the other.

Able to fit small bundles, these thin ties are more flexible than other ties.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

These ties stretch to hold material tightly without slipping.

Feed a bundle through the closed loop and wrap the ends around pipe or conduit for support.

Stick these ties to any smooth, clean surface.

Keep a set of these differently sized cable ties on hand to use when you need them. They're flexible, reusable, adjustable.

Woven from flexible stainless steel yarn and Nomex, these ties handle temperatures up to 850° F.

Attach these cable ties directly to a surface—no separate mount needed.

Mount to a surface and add a cable tie to secure a bundle.

For use in environments subjected to chemicals, these mounts withstand the most corrosive conditions.

Create fast connections with items, such as rope, chain, and straps.

A wide opening accepts large diameters of rope and pipe. Squeeze the trigger to release.

Squeeze the trigger to quickly release the latch.

The force of the load helps keep the arms closed. Press the trigger for quick connection and disconnection.

The most secure carabiner we offer, these carabiners won’t accidentally open when rope slides because you need to unscrew the latch to unlock them.

Prevent twisting in your rope or line with these swiveling carabiners. To open, pull the latch down, twist 90° and push in.

For extra security, these have a latch that snaps back into place to secure your load.

The spring-loaded latches on these hooks snap back into place, securing your load.

Join, organize, and suspend objects with these S-hooks.

One side is closed and the other is open.

Constructed with a saddle for both the long (live) end and the short (dead) end, these clamps apply equal pressure without crimping or crushing the wire rope, so orientation doesn't matter. Also known as fist grip wire rope clips.

Kits include clamps and thimbles to support a wire rope loop and prevent it from fraying. Clamps must be oriented with the saddle on the long (live) end and U-bolt on the short (dead) end.

Use in noncritical applications, such as fencing, where the strength of a forged clamp is not required. Install clamps so the saddle is on the long (live) end and the U-bolt is on the short (dead) end. They’re also known as wire rope clips.

Install these clamps without any specific orientation, slide the nut over the rope and tighten it onto the threaded halves with a torque wrench.

Slide these clips on DIN rails—often used in equipment cabinet racks—to route and organize cables. Since these clips don’t require adhesive or screws, you can move them anywhere along the rail.