Add push-in cable holder to this adapter to mount cable to DIN rail.

Keep individual wires separate by laying them between the coils on these holders.

Attach with a screw or other fastener.

Stick these ties to any smooth, clean surface.

Easily transport or hang cords, rope, and hose—these hook and loop cable ties include a handle.

The buckle allows you to cinch these ties tight.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

These ties stretch to hold material tightly without slipping.

The hook and loop on these ties holds more tightly than other hook and loop.

Create custom-length ties from a roll with hook on one side and loop on the other.

These ties meet UL flammability requirements.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

Woven from flexible stainless steel yarn and Nomex, these ties handle temperatures up to 850° F.

The buckle allows you to cinch these ties tight.

Use these plastic mounts with metal-detector-grade cable ties when detection and retrieval is essential, such as in food processing applications. Mounts are brightly colored for visibility and contain a special compound that can be picked up by X-ray equipment and metal detectors.

Prevent wear to bundles by mounting these spacers between two bundles.

For use in environments subjected to chemicals, these mounts withstand the most corrosive conditions.

Identify bundles at a glance.

These ties are less likely to crack and break from dryness than regular cable ties.

Reduce gaps between the cable tie and bundle—these ties have a smooth body that allows them to adjust to the exact size of the material.

Tighten cable ties and trim the excess with these tools.

Use the built-in blade to remove excess length once these ties are secure.

Bundle and secure cable, wire, and hose.

The tail slots into the head to create a temporary loop to hold wires. Hook and unhook the loop to add additional wires before permanently cinching the tie.

The head of these cable ties is contoured to fit against pipe, tubing, and other round material for a tight fit.

Secure and separate parallel bundles with the same tie.

These strong, wide ties are often used as an alternative to metal strapping.

Often used as tamper seals and in tagging applications, these ties create a consistent loop size every time.

With a thin, flexible body, these cable ties fit tightly around irregularly shaped bundles.

These ties meet UL flammability requirements.

A foam padded back combined with an extra-wide body protects sensitive bundles, such as fiber optic cable.

Take the guesswork out of identifying material—use the attached tag to label the bundle.

A hard rubber coating and wire core helps these ties maintain their shape.

These ties have a loop on each end that can be twisted around each other for a secure closure.

Bundle, close, and label bags and sacks.

Loop and twist bale and bundle twist ties.

Ties come on a spool for use in a twist tie machine.

Identify bundles at a glance with these ties that are coated for an additional level of corrosion resistance.

The ripple in the body prevents over tightening and allows for expansion to protect material that frequently changes size, such as heat cable.

The plastic coating on these ties adds an additional level of corrosion and abrasion resistance over other stainless steel cable ties.

These stretchy ties conform to irregularly shaped bundles to grip material tightly.

Secure and separate two bundles with the same tie.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

Quickly mount parallel lines of pipe, hose, or tubing by clicking them into these clamps. Made of acetal, they are UV-resistant and can be used outdoors.

Slide these clamps into strut channel and snap closed for quick installation with no tools required. They are noncorrosive, nonconductive nylon.

Mount parallel lines of pipe, tubing, or conduit directly against the mounting surface.

Even when these clamps are installed side by side, the clamping screws remain accessible. Use them to route pipe, tubing, and conduit across strut channel.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

Mount these ringbolts into a threaded hole, or use the nut for through-hole mounting. The pivoting ring allows material to move freely.

Hang cable and other flexible material beneath wire to prevent it from sagging and swaying. To install, hook the two ends of the ring around the wire—no fasteners required.

Keep multiple bundles of wire and cable on separate hooks. The hooks have wide openings to allow access for installation, adjustment, and removal.

These plastic rings won't conduct electricity. Also known as distribution rings, they have a large opening for routing multiple cables. A smooth surface prevents damage to wire and cable.

Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.

Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.

These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.

Cut as much strap as you need to hang duct, pipe, and other materials.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.