Extra-thick walls provide more protection against abrasion and tears than standard high-shrink-ratio tubing. This tubing shrinks down to 1/6th of its original ID, so it creates a tight seal over irregularly shaped objects.

For better protection against abrasion, tears, and punctures, this tubing has thicker walls than standard tubing.

Access connections more easily than with standard heat-shrink tubing. Make a small slit in this tubing to peel it away.

Create a water-resistant seal—this tubing has an adhesive lining that melts when the tubing is heated and bonds to the underlying surface.

This PTFE tubing withstands temperatures up to 450° F and has an inner lining that creates a water-resistant seal when heated.

Create a tight, water-resistant seal over irregularly shaped components. When heated, this tubing shrinks down to about 1/6th of its original ID, while an adhesive lining melts and forms a barrier around your component.

This tubing shrinks down to a quarter of its original ID, so it creates a tight seal over irregularly shaped objects. It withstands up to 500° F.

With thin walls, this tubing shrinks faster than other high-temperature tubing. It withstands up to 500° F.

Resistant to diesel fuel, gasoline, hydraulic fluid, and lubricating oil, this tubing is often used in vehicles.

Made of woven polyolefin/polyester fabric, this tubing has excellent abrasion resistance so it can be dragged over rough surfaces without damage.

Insulate and protect high-voltage devices. This tubing withstands higher voltages than standard heat-shrink tubing because it’s made of a flame-retardant material with excellent electrical insulation properties.

Also known as halogen-free tubing, this tubing produces minimal amounts of smoke and gas if exposed to an open flame, so it can be used in enclosed areas such as ships and tunnels.

Approved for contact with food, this tubing is FDA Compliant 21 CFR 177.1330.

Protect light bulbs, capacitors, and other electronics—this FEP tubing adds a tear- and cut-resistant layer that even contains shattered glass if the bulb breaks.

Keep general purpose tubing in a variety of sizes on hand.

A different shrink ratio on each end allows this tubing to fit over cable assemblies and wire harnesses with large connections, or around connectors with a 90° elbow.

Also known as breakout boots, these splitters insulate and seal the point where wire splits off from cable, or where cables exit from conduit.

Protect wire and cable without disconnecting them from an assembly. For a water-resistant seal, this tubing has an adhesive lining that melts when heated to bond it to the underlying surface.

With a spiral-wound core, these end caps form a permanent seal on the end of your crimped wire or cable without heat or tools.

Protect cable, hose, and pipe in high temperature environments—this sleeving withstands temperatures over 450° F. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Tight braiding makes this sleeving resistant to fraying when cut with scissors. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

Tested to meet MIL-STD-202, this sleeving meets performance standards for flame retardance. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

With excellent torsional strength, this sleeving withstands the extreme twisting found in robotics. It has impact strength similar to steel yet is lighter than most other sleeving materials. Stretch it to fit over items for easy installation; it tightens around its contents for a secure fit.

Made of PPS plastic, this sleeving shields cable, hose, and pipe from oil, acids, and other chemicals. It stretches to fit over items for easy installation, then tightens around its contents for a secure fit.

This sleeving is often used to insulate connections in transformers and relays. It prevents electricity and heat from dissipating from wire and cable.

A specially formulated silicone rubber coating allows this sleeving to stretch over items during installation; it then tightens around its contents for a secure fit.

A silicone rubber coating on this fiberglass sleeving protects against sparks and molten metal splash.

Unlike fiberglass and silica, this sleeving won't irritate skin, so it's easier to handle. It has a temperature rating of 1100° F or higher.

A blend of Aramid and fiberglass gives this sleeving excellent abrasion resistance. It can withstand temperatures up to 650° F

Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.

Coated in acrylic, this sleeving holds up to rapid temperature changes, and it won’t break down from refrigerants, solvents, oil, or lubricants. Also known as hermetic sleeving, it’s designed to protect wires and hose inside air-tight motors, such as those used in air conditioners.

Made of nylon, this sleeving is the most impact- and abrasion-resistant slit corrugated sleeving we offer. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them.

Rated UL 94 V-2, this sleeving resists combustion and minimizes the spread of flames. A slit along the length makes it easy to install over wire, cable, and hose without disconnecting them. It has impact and abrasion resistance similar to conduit, with more flexibility.

The corrugated construction gives this sleeving impact and abrasion resistance similar to conduit, but with more flexibility.

With a flat, oval shape, this sleeving fits better in confined spaces than standard corrugated sleeving.

A hinge along the entire length makes this one-piece sleeving easy to open for installation. Interlocking ridges overlap along the opening to protect contents from dust and dirt. The corrugated construction gives it the impact and abrasion resistance of conduit, with more flexibility.

A strip of hook-and-loop creates a strong seal along the entire length of this sleeving, yet it can be opened at any point to access contents. Use it to wrap around wire, cable, or hose without disconnecting them.

Snaps keep this sleeving securely closed, yet permit quick access to contents and allow you to route wires in between the snaps. Use it to easily wrap around wire, cable, and hose without disconnecting them.

The tightly braided construction makes this polyester sleeving abrasion resistant. It has a slit along the entire length so it easily wraps around wire, cable, and hose without disconnecting them.

Use this shielded sleeving to protect wire and cable from signal distortion caused by nearby equipment and devices. It has a slit along the entire length so it easily wraps around wire and cable without disconnecting them.

Often used in robotics and other automated applications, this sleeving adds an extra layer of protection and insulation to cable and hose carriers.

Insulate your wire, cable, and hose in continuous temperatures up to 400° F and easily access them. This sleeving opens anywhere along its length with a hook-and-loop strip.

Sheathe cable, wire, and hose in a protective cover in case of a fire. Rated VW-1, this sleeving meets requirements for preventing the spread of flames based on a timed test with vertically suspended material.

To stop rodents from chewing on this sleeving and damaging your wire, cable, or hose, it’s reinforced with glass fibers that irritate rodents’ gums. Wrap it around components without having to disconnect them.

This sleeving absorbs UV light, so it can be used in direct sunlight without getting damaged. A reusable alternative to tape and cable ties, it allows you to route wire and cable between the spirals.

Made for bundling wire, cable, and hose in high-traffice areas—this sleeving is HDPE plastic, so it stands up to wear and crushing forces better than standard spiral sleeving.

With a unique overlapping link structure, you can open and close this sleeving like a zipper using the included tool. The tool’s open design and the slots in the sleeving make it easy to branch off wires from your bundle as you’re zipping it shut.

Identify wear and tear on your sleeving before its contents become exposed. This sleeving has a yellow inner layer that shows through when the black outer layer wears off.

Avoid tripping over wire, cable, or hose in the dark—this sleeving glows in the dark for up to 12 hours.

Made of neoprene rubber, this sleeving has excellent abrasion resistance. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.

With a copper and nickel exterior and conductive lining, this sleeving shields your wire and cable from signal interference. You can wrap this sleeving like tape around wire and cable while they’re installed, so it’s great for emergency patches.

Quickly set foam backer rods in caulk joints at a consistent depth without puncturing them.