Hinge leaves fit into two cutouts (mortises) to mount flush with the door and frame.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Made of plastic with a metal additive, these hinges will set off metal detectors if a piece breaks off and falls into your line.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

These hinges are made of metal.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Also known as bullet hinges, these hinges are the right size for tight spaces and narrow frames.

Tighten or loosen an adjustment screw to change the hinge resistance.

These hinges allow 360° of motion.

In addition to rotating 360°, these hinges tilt up and down.

To retract the pin and disconnect a door, squeeze the hinge handles together. Release the handles and the pin snaps back.

A keeper holds the pin in a retracted position to make reconnecting doors easier than other pull-release quick-disconnect hinges.

To make reconnecting doors easier than other pull release quick disconnect hinges, these have a keeper that holds the pin in a retracted position.

A stop keeps these hinges open at a set angle; push past the stop to open them to 180°.

Springs in these hinges with holes automatically swing doors and gates closed behind you.

After a light push on the door, springs in these hinges swing doors and gates fully open.

Only one cutout (mortise) is needed for these hinges—the offset design allows surface mounting the door leaf and mortise mounting the frame leaf.

Longer than other entry door hinges, these piano-style hinges run the entire length of doors for strength and durability.

These hinges are completely hidden when the door is closed.

Bearings allow these hinges to open and close doors smoothly. The mounting holes form an industry-standard half-moon shape.

The mounting hole pattern does not follow an industry standard, which means you can work around worn mounting holes when replacing template hinges.

Bearings allow these hinges to open and close doors smoothly.

The mounting hole pattern does not follow an industry standard, which means you can work around worn mounting holes when replacing template hinges.

Create precise outlines for hinge mortises (cutouts). Position the cutter on a wood door or frame and hit it with a hammer to imprint the outline.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Keep environments free of contaminants—with plastic hinge leaves and a metal pin, there's no metal-to-metal contact that can release particles as hinges open and close.

Designed to wrap around the edge of the partition frame, these hinges provide a stronger hold than other toilet partition door hinges.

These hinges have a standard range of motion of 100° to 120°.

With a 170° range of motion, these hinges are for doors that need to open wide.

To ensure a good fit, these hinges have screws for horizontal, vertical, and depth adjustments after installation.

Easier to install than other mortise-mount concealed cabinet hinges, these fit in two drilled holes.

Instead of mounting to the side of a door, mount these hinges to the top and bottom to allow doors to open wide.

Slip the hinge pins into 11/32" Dia. × 5/16" Dp. holes in a cabinet.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

A spring in these hinges automatically swings doors and gates closed behind you.

The hinge pin attaches to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Wide hinge leaves provide a large mounting surface to keep trailer doors from sagging.

These hinges are made of metal.

Made of carbon fiber, these hinges are as strong as aluminum yet lighter in weight. All have leaves that are connected by a strip of flexible Kevlar instead of a pin.

No need for drilling holes or welding, slip these hinges onto panel and door edges for a secure fit.

When the door is closed, the distance between the leaves is larger than the pin diameter, creating an offset to accommodate a gasket or trim.

No separate hinges are required, these supports act as a hinge and lid support all in one. Springs provide lifting assistance to raise and hold lids open—slightly lift the lid to get it started and the support will do the rest. Manually shut the lids and the supports will hold them in the closed position.

Commonly used on hood and trunk lids, these simple, three-piece rods telescope from 18 1/2" to 46 3/4" to prop lids open at a variety of angles.

Keep environments free of contaminants—with plastic bushings, there's no metal-to-metal contact that can release particles as these supports open and close. Manually control these free-moving lid supports through their full range of motion. Raise the lid until the hold-open mechanism on the support is engaged; slightly lift it again to release the hold and close the lid.

Hold heavy lids open with these supports.

Requiring less space to mount and operate, these supports are often used on small cabinets and enclosures. They gradually slow your lid's motion to prevent it from slamming open. To open lids, lower them and the support will slowly and softly do the rest. Manually shut the lids and the supports will hold them in the closed position.

Add legs to these brackets and mount to a tabletop to create a folding table.

Add a secondary panel that swings to mount more components in your enclosure.

Build test fixtures, prototypes, and other small structures with this miniature version of T-slotted framing and fittings.

No need for fasteners—friction holds this framing together. Use press-fit framing and fittings to assemble carts, enclosures, and partitions.

Use hinges to add doors, lids, and machine guards to T-slotted framing.