We will reply to your message within an hour.
More
A time-saving alternative to strap hangers, these hangers fit a range of material sizes without any cutting and easily adjust after they’re installed.
Load material between the two halves of the ring and adjust the side bolts for a tighter fit than standard threaded-rod-mount clamping hangers.
Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.
Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.
These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.
Connect these hangers to organize multiple lines of pipe, tubing, and conduit. The tight-fitting, santoprene body reduces vibration and prevents corrosion caused by metal-to-metal contact.
Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.
Clip these hangers onto the side of threaded rod. Unlike other threaded-rod-mount hangers, you can use more than one hanger on the same rod to organize multiple lines of pipe, tubing, and conduit.
Lock your line in faster than any other hanger. These hangers automatically close when you press your line into the clamp.
These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.
These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.
A roller on the bottom of these hangers compensates for movement due to expansion and contraction, such as in hydraulic applications. Combine with a threaded rod or other fastener to hang from the ceiling.
Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.
Access material quickly without uninstalling the mounted hanger. These hangers have a removable bolt for loading pipe, tube, and conduit from the side. Combine them with a threaded rod or other fastener to hang from the ceiling.
Use these hangers in corrosive environments and where chemicals are present. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.
Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.
Route multiple lines of pipe, tubing, and conduit with a single hanger. A wide opening and locking tab allow access for installation, adjustment, and removal.
For a strong, secure connection, mount these hangers by welding them to a rod.
Reduce movement in your line with hangers that are more rigid than strap hangers and fit tighter around pipe, conduit, and tube than loop hangers.
A versatile solution for temporary hanging of pipe and tubing at work sites as well as anywhere welding and fastening are not possible. Feed material through the strap, then use the D-rings to adjust the hanging height.
Use these close-fitting hangers for a more rigid hold around material than when using straps alone.
Cut as much strap as you need to hang duct, pipe, and other materials.
To hold and support large or small round or cylindrical workpieces, position these two-piece V-blocks to accommodate any diameter.
When high precision isn’t critical, choose these V-blocks to hold and position round workpieces.
Precision ground to tight tolerances, these V-blocks help you accurately align and support round workpieces.
Place into larger V-blocks to hold small shafts and cylinders. Sets include two clamps that fit different diameters.
Use this block to hold workpieces at precise angles.
Magnetic surfaces on the bottom, back, and one V face of these blocks eliminate the need for mounting clamps and bolts.
Set these V-blocks onto a magnetic chuck or plate to lock metal workpieces in place—no fussing with clamps or bolts.
With vees in three different sizes, these blocks can support rods and shafts in a wide range of diameters.
Choose from flat and grooved liners.
These V-shaped liners hold large round material.
Insert these one-piece grooved liners between vise jaws to hold small-diameter material vertically.
Replace worn flat and V jaws.
The V‐shaped recess holds round material securely for machining.
Gravity keeps long loads centered and balanced—great for pipe, bar stock, and channel.
The combination of an offset handle and V-shaped cradle lets one person balance and move large, long loads.
Move a drum where you need it, then dispense.
Store, mix, and drain drums in a single location.
Spills while dispensing drums are contained in an internal sump, so you can transport the drum even after a spill occurs.
These corrosion-resistant stainless steel trucks withstand harsh environments and frequent washdowns.
Tilt these trucks and roll them like a hand truck to move drums. They tilt flat for dispensing.
Instead of tilting these trucks during transport, push on the handle to lift a drum straight off the ground and move it easily over obstacles. Push the handle down to tilt the drum to dispense.
Lift, transport, and place drums without a forklift. Roll these trucks right to the edge of your pallet or platform to load and unload drums.
These dispensers mount to the forks of a forklift for lifting and transport, plus they pivot for manual tilting so dispensing is easy.
Slide onto the forks of a forklift to raise a drum, then use the hand chain to tilt and drain it from up to 10 feet away.
Lift heavy drums in seconds—without ever touching them. Powered by a battery-operated hydraulic pump, these trucks grip, lift, lower, and release drums with the push of a button.
With the push of a button the hydraulic lift raises the drum, while the chute controls the flow of the material being dispensed to prevent splashes and spills.
A second set of axle-mounted wheels offers better load support and stability to handle heavy loads over longer distances.
A hydraulic lift raises the drum to the required height, and a manual tilt mechanism positions the drum at the proper angle for emptying.
These two-wheeled trucks are good for moving drums short distances.
Stakes at each corner hold loads in place during transport and are easily removed for unloading.
Easily assemble and reconfigure as your needs change.
Also known as cantilever racks.
Use individual components to create your own personalized storage solution. These racks are also known as cantilever racks.
Store bars, spools, and other items on a single versatile rack.
These cantilever racks are made to be used with forklifts and cranes.
With multiple heights, widths, and arm styles to choose from, create a rack that fits your needs. These racks are also known as cantilever racks.
To create a convenient dispensing station, place your round, 5-gallon safety can in these stands.
Snap laptops and tablets into these holders to mount them on stands and positioning arms.
Keep smartphones and irregularly-shaped devices, such as radios, in sight and within reach. These arms mount to a variety of surfaces and have 360° range of motion thanks to their ball-and-socket joints.
Position your tablet within view while keeping your hands free to work. These arms mount to a variety of surfaces while keeping a secure grip on your tablet.
These arms lock around the top and bottom edges of tablets to keep them from shaking loose in areas with strong vibrations.
Made in pairs, these V-blocks are precision ground to tight tolerances for straight sides, square corners, and centered grooves.
Use these V-blocks to support rods, shafts, and other cylindrical workpieces for precise inspection or measuring tasks.
Use with overhead lifting equipment to vertically lift closed-head drums and open-head drums with tightly secured lids.
Raise, transport, tilt, and drain full drums using the hook of a crane or hoist.
Hook these lifters to a crane or hoist to pick up 5-gallon pails and pour out their contents.
Free your hands for other work by mounting a flashlight to a nearby surface.
Attach and position phones, tablets, monitors, and computer accessories on T-slotted rails.
Prop up and display tablet computers to keep your hands free for touching, swiping, and other tasks.
Free up cargo space—these racks mount to a truck or van to haul ladders and other long material.
Clamp an outlet strip to your work surface to quickly plug in and unplug devices.