Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts in metal. Wheels are reinforced with two layers of fiberglass mesh. Choose coarser grit for fast cuts; choose finer grit for smooth cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Made of premium grade abrasives, these wheels make fast, burr-free cuts in stainless steel. They’re reinforced with two layers of fiberglass mesh. Choose coarser grit for fast cuts; choose finer grit for smooth cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Often used on duct, these ultra-thin wheels make fast, clean cuts in thin metal that minimize burrs and discoloration from heat. Also known as Type 27, raised-hub, and depressed-center cutoff wheels, they outperform Type 1 wheels when making flush cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts. They make fast, burr-free cuts in stainless steel. Wheels are reinforced with two layers of fiberglass mesh. Choose coarser grit for fast cuts; choose finer grit for smooth cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Made of ceramic alumina or a combination of ceramic alumina and zirconia alumina, these wheels last up to ten times longer than standard cutoff wheels when cutting hard metal such as Inconel nickel, Hastelloy nickel, and tool steel. Wheels are reinforced with two layers of fiberglass mesh.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Made of ceramic alumina, these wheels last 10 times longer than standard cutoff wheels when cutting hard metal, such as tool steel. They’re reinforced with two layers of fiberglass mesh. These wheels, also known as Type 27, raised hub, and depressed-center cutoff wheels, outperform Type 1 wheels when making flush cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Run these high-density aluminum oxide wheels at higher speeds than standard cutoff wheels to make quick cuts in aluminum, iron, stainless steel, and steel. Wheels are reinforced with a layer of fiberglass mesh.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Made of premium grade abrasives, these wheels are strong and thick for making notches in aluminum, iron, stainless steel, and steel. They’re reinforced with two layers of fiberglass mesh. Also known as Type 27, raised-hub, and depressed-center cutoff wheels, they outperform Type 1 wheels when making flush cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Ideal when working across multiple materials, these wheels are specially constructed to cut plastic, fiberglass, concrete, and ceramic, as well as metal. They also work with sheet metal. They contain less than 0.1% iron, chloride, and sulfur contaminants to prevent corroding and discoloring stainless steel and other nickel-alloyed steel.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

These high-density ceramic or ceramic oxide wheels have two layers of fiberglass mesh reinforcement and last up to twice as long as long-life cutoff wheels when cutting iron, stainless steel, and steel.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Prevent corrosion and discoloration on stainless steel—these wheels contain less than 0.1% iron, chloride, and sulfur contaminants. They have an aluminum oxide grit and are reinforced with two layers of fiberglass mesh. Choose coarser grit for fast cuts; choose finer grit for smooth cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Make cuts in hard, brittle materials such as firebrick, stone, and concrete. Wheels are made of silicon carbide abrasive that is reinforced with a layer of fiberglass mesh.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Made with diamond, the strongest abrasive material, these wheels are extremely hard and wear resistant, so they stand up to ceramic and glass.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Switch between cutting and deburring aluminum, iron, stainless steel, and steel without the need to change your wheel. Three layers of fiberglass mesh reinforce these aluminum oxide wheels. They're also known as Type 27, raised-hub, and depressed-center cutoff wheels, and they outperform Type 1 wheels when making flush cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Use these clog-resistant wheels to make quick cuts in soft metal such as aluminum, brass, and copper. They are reinforced with two layers of fiberglass mesh. Choose coarser grit for fast cuts; choose finer grit for smooth cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts. They make quick cuts in soft metal such as aluminum, brass and copper without clogging. Wheels are reinforced with two layers of fiberglass mesh.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts. They contain less than 0.1% iron, chloride, and sulfur contaminants, so they won't corrode or discolor stainless steel. Wheels are aluminum oxide abrasive that is reinforced with two layers of fiberglass mesh.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Use these wheels to cut through metal such as iron, stainless steel, and steel. They are reinforced with a layer of fiberglass mesh. Choose coarser grit for fast cuts; choose finer grit for smooth cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Made of premium grade of abrasives, these wheels are strong and thick for making notches in stainless steel. They’re reinforced with two layers of fiberglass mesh. Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

For quick cuts in stainless steel, run these high-density zirconia alumina wheels at a higher rpm than standard cutoff wheels. They’re reinforced with a layer of fiberglass mesh.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Cut wood, plywood, and particleboard. These blades bite into wood to make both straight and plunge cuts, so they can be used to cut lumber down to size and slice through material that’s already installed. When choosing a blade, you’ll want to keep in mind the number of teeth and width of cut. Choose more teeth for cutting across the grain; choose fewer teeth for cutting with the grain (ripping) and for cutting thicker materials. A narrower cut width makes faster cuts with minimal material loss; a wider cut width increases stability for straighter cuts.

Warning: Use wheels that have a greater rpm rating than the no-load rpm of your tool.

Diamond grit bonded to a segmented edge cuts through hard metal such as cast iron and steel. Use dry or with water or coolant (not included). All blades come with a reducer bushing to adjust the arbor diameter. Blades with a narrower width of cut make faster cuts with less material loss.

The edge of the blade is segmented to cut faster than a continuous edge. These blades have diamond grit that lasts up to three times longer than the grit on other blades for masonry and stone in continuous use applications on hard, abrasive materials. Use dry or with water or coolant (not included). Blades come with a reducer bushing to adjust the arbor diameter. For blades with a round/diamond arbor, detach the center piece to expose the diamond shape.

A continuous edge coated in diamond grit makes fast, smooth cuts in stone and ceramic tile. Blades with multiple arbor diameters come with a reducer bushing.

A continuous edge on these blades produces smooth cuts. They have diamond grit that lasts up to three times longer than the grit on other blades for masonry and stone in continuous use applications on hard, abrasive materials. Use dry or with water or coolant (not included). Blades come with a reducer bushing to adjust the arbor diameter. For blades with a round/diamond arbor, detach the center piece to expose the diamond shape.

The edge of the blade is segmented to cut faster than a continuous edge. It's coated in diamond grit to cut hard, abrasive materials such as masonry, stone, asphalt, and concrete. Use dry or with water or coolant (not included). Blades come with a reducer bushing to adjust the arbor diameter. For the blade with a round/diamond arbor, detach the center piece to expose the diamond shape.

Use these blades with water or coolant (not included) to produce smoother cuts in stone and ceramic tile than dry-cutting blades. They're also for use on glass. They have a continuous edge coated in diamond grit. Blades with multiple arbor diameters come with a reducer bushing.

A continuous edge on these blades produces smooth cuts. It's coated in diamond grit to cut hard, abrasive materials such as masonry, stone, asphalt, and concrete. Use dry or with water or coolant (not included). Blades come with a reducer bushing to adjust the arbor diameter. For the blade with a round/diamond arbor, detach the center piece to expose the diamond shape.