Made with industry standard barrel-style ends, these connectors carry DC power between electronic devices and power supplies.

Each set includes one plug and one socket. These connectors withstand moisture, harsh engine fluids, and high temperatures. Also known as weather-pack connectors.

Install these connectors in panels, enclosures, and bulkheads to join equipment with compatible Deutsch-style DC connectors.

A sealed housing protects connectors from weather. Sets include a plug and socket with wire leads already installed. They fit standard Molex connectors.

Also known as power-pole connectors, these single-pole connectors join two pin connections, rather than a pin and socket. They stack from the top and sides to form any configuration.

Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. They fit AMP MATE-N-LOK connectors.

Power hydraulic and air-powered valves, motors, pumps, and pressure switches.

Protect Mil. Spec. connectors when not in use.

These connectors have the same pin and socket configuration as connectors that meet MIL-DTL-26482, so they can be used with products that meet the same standard. Quickly mate them by pushing them together.

Rated IP69K, these M16 connectors protect against dust, debris, and hot, high-pressure jets of water at high volumes.

Because they tightly thread to M12 connections, these connectors won’t let contaminants in or come loose from vibration in rugged industrial environments and automated systems as they send power and signal or just power to your equipment.

Safely use these connectors with 12 mm proximity switches, console lights, valves, and power supplies in food, beverage, and pharmaceutical applications—they’re FDA compliant for direct food contact.

Visually confirm your connector is working properly. A green light means your connector has power, while yellow means it has signal.

Protect harsh environment M12 connectors when not in use.

Protect screw-together M12 connectors when not in use.

Protect against signal interference while sending 2-3 times more current than M12 connectors.

Also known as pico connectors, these connectors are often used with 8 mm and smaller proximity switches and photoelectric switches.

Protect mini connectors when not in use.

Visually check that your low-current devices with M8 connections are powered up and sending and receiving signals. These connectors illuminate green if they have power and yellow if they have signal.

Protect harsh environment mini connectors when not in use.

A TPE cable protects these connectors from oil, weld slag, and other tough industrial stresses as they send signal and power to low-current devices with M8 connections.

Send higher current than M12 connectors to automated systems, motors, and pumps in environments where washdowns are common.

Modify your M12 or mini connection to match cords and I/O modules in your system.

Also known as dummy plugs, these plugs close the electrical circuit on your mini connector, so you can safely change devices or repair connections.

Connect different pole configurations to join sensors, switches, and other devices to cords, distribution blocks, and I/O modules.

Push these connectors together to quickly create signal and data connections in tight spaces. They need less space to mate than screw-together connectors, which require two hands to twist them in place.

With a PVC housing, connectors withstand exposure to chemicals, oil, fuel, and salt water.

Power small devices, such as chargers for electronics, from a vehicle. Also known as cigarette-lighter plugs and sockets.

Power robotic arms and other high-amperage machines in motor controls, conveyors, and sorting and packaging systems from your main M35 power line.

Often used in devices that branch off of the main power line, these connectors power high-amperage fans, pumps, and machines in motor controls, conveyors, and sorting and packaging systems.

With thick threads similar to a light bulb, these connectors take only a few turns to lock into place for a secure connection in washdown and high-vibration areas. Detach them just as quickly for frequent maintenance.

Mount these receptacles to control cabinets and equipment in order to quickly connect and disconnect M29 power cords.

FDA compliant to safely touch food and threaded for a tight hold, these connectors won’t vibrate loose as they send high-speed data to sensors and other automated devices in food, beverage, and pharmaceutical plants.

Connect two stereo cords through a panel with these adapters.

Couple these adapters with a cord that matches your outlet and length requirements to run DC-powered electronics.

To run DC-powered lab and medical equipment from your outlet, add a power cord with the plug style and length you need. These adapters meet strict IEC, UL, or ANSI/AAMI standards for use with medical devices.

Plug these cords into a vehicle socket to charge devices that run on AC voltage.

Carry DC power in or out of electronic devices with these cords. All have industry standard barrel-style connections, letting you power electronics from power supplies.

Use these cords with hydraulic and air-powered valves, motors, pumps, and pressure switches. They have a solenoid valve socket on one end and an M12 threaded plug on the other.

Use these cords in vehicles and other agricultural and construction equipment.

Connect multiple M8 and M12 cords to create a network between equipment. These blocks are often used to send signal and power to proximity switches and sensors.

Connect two devices to a distribution block or I/O module with just one cord. Often used with sensors and actuators, these splitters send power/signals to your devices through a single connection.

FDA compliant for direct contact with food, these cords are safe to use with 12 mm proximity switches, valves, and power supplies in food, beverage, and pharmaceutical applications.

With a single cord, these splitters join two devices with M12 connectors to a distribution block or I/O module with M12 connectors. Often used with sensors and actuators, they send signals/power to your devices through one connection.

Send signal and power to low-current devices with M8 connections near welding, metal machining, and in spots where temperatures change.

A few turns is all it takes to join these cords, which have thick threads similar to a light bulb, for a secure connection in washdown and high-vibration areas. They detach just as fast for frequent maintenance.

Like a tree trunk connecting to branches, these cords supply power to a chain of devices. Send power to high-amperage motors, robotic arms, and other machines in motor controls, conveyors, and sorting and packaging systems.

Play audio from one source on two different speakers.

Use with DIN 3 rail. Add as many circuits as you need with these terminal blocks and accessories.

Quickly troubleshoot or change wiring without any tools. These terminal blocks have a lever clamp that you flip up to insert wiring and flip down to lock it in place.

Made of ceramic, these blocks withstand high-temperature applications that reach up to 1110° F such as ovens and furnaces. They have recessed screws to reduce the chance you’ll cause a short by accidentally connecting two circuits with a screwdriver or other tool.

Mount blocks to a panel or the surface of a machine. Also known as barrier terminal strips.

Save time when wiring connections in a junction box; these blocks come already installed in an enclosure.

Recessed screw terminals prevent you from accidentally connecting two circuits with a screwdriver or other tool, causing a short.

Best for equipment requiring regular servicing, these blocks disconnect without having to remove any wiring thanks to their plug-and-socket design. Their recessed screws prevent shorts by reducing the risk you’ll connect two circuits with a screwdriver or other tool.

Protect connections against corrosion.These bars are tin-plated copper and have stainless steel terminals.

With the help of distribution blocks, you can take a high-current wire from your power source and connect it to one or more electrical devices.

Connect these lifters to your robot arm to pick up and move items using suction. They're electric, so you don't need a compressed air source.