McMaster-Carr logo
    Filter by
    System of Measurement
    For Hole Type
    Thread Type
    Industrial Info Compare
    Component
    Thread Direction
    Chamfer Type
    Container Type
    Number of Pieces
    OD
    Attribute Image
    Finish
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    For Threading
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    3 Products

    Tap, Die, and Thread File Sets

    Image of Product. Front orientation. Tap, Die, and Thread File Sets.
    Repair screw threads in a wide range of sizes. The dies are hex shaped for use with conventional wrenches. The taps have a square shank that's compatible with tap wrenches and tap holders for drill presses and drilling machines. With a plug chamfer, all taps have 3-5 chamfered threads and are suitable for thread repair in both through holes and closed-end holes.
    No. of
    Pieces
    Tap Sizes Included
    Die Sizes Included
    File Sizes Included
    Container
    Type
    Each
    Carbon Steel
     
    Right-Hand Thread
    481/2"-13, 1/2"-20, 1/4”-20, 1/4”-28, 3/8"-16, 3/8"-24, 5/16"-24, 5/16”-18, 7/16"-14, 7/16"-20, 9/16"-18, 9/16”-12, M6 × 1.00 mm, M8 × 1.25 mm, M10 × 1.00 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.25 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.50 mm1/2"-13, 1/2"-20, 1/4"-20, 1/4"-28, 3/8"-16, 3/8"-24, 5/16"-18, 5/16"-24, 5/8"-11, 5/8"-18, 7/16"-14, 7/16"-20, 9/16"-12, 9/16"-18, M6 × 1.00 mm, M8 × 1.25 mm, M10 × 1.00 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.25 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.50 mmFor 0.75 to 3 mm thread pitches, For 11 to 24 threads per inchPlastic Case000000000000000
     

    Dies

    Image of Product. Front orientation. Dies. Dies.
    Rotate these dies around studs and rods to create new fastener threads. A cut above lower-quality dies that can leave inferior threads, these are machined in the U.S. to precise dimensions for accuracy and consistency.
    They are adjustable, so you can cut a shallow thread that makes it easier to get the die started on the first pass. Turn the set screw to open the die to its largest diameter. Then rotate the die with a round die wrench and adjust the screw as you make additional passes to reach the proper thread size.
    Uncoated High-Speed Steel—The most versatile dies stay sharp and cut cleanly, even if you use them every day. They last much longer than carbon steel dies and you won’t have to work as hard to create threads.
    Dies
    Die Wrenches
    Uncoated
    High-Speed Steel
    Thread
    Size
    Thread
    Type
    Each
    Each
    2" OD
    3/4"-20
    		UNEF
    		000000000000000000000000000000
     
    back to top