M6 Dies | McMaster-Carr

Cut and repair threads and drill holes in many different sizes. Tap and die wrenches are included. The dies are hex shaped for use with conventional wrenches. The taps are made of carbon steel and are recommended for thread repair and occasional tapping.

Taper Chamfer—Taper chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. They require less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes.

Plug Chamfer—Plug chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they do not start threads as easily as taper chamfers. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.

	Drill Bit Sizes Included	Container Type	Includes	Tap Chamfer Type		Each
Carbon Steel







	Right-Hand Thread

	117	4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/8"-28, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	4-40, 6-32, 8-32, 10-24, 10-32, 12-24, 1/8"-27, 1/8"-28, 1/4"-20, 1/4"-28, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24, 7/16"-14, 7/16"-20, 1/2"-13, 1/2"-20, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	5/64", 7/64", 5/32", 1/4", 19/64", 5/16", 21/64", 3/8", 25/64", 13/32", 27/64", 29/64", 43 ga., 39 ga., 36 ga., 30 ga., 29 ga., 25 ga., 21 ga., 20 ga., 16 ga., 9 ga., 7 ga., 3 ga., B, F, H, I, J, O, Q, R, S, U, Z	Plastic Case	Die Wrench (2), Extractor (5), Tap Wrench (3), Thread Gauge (2)	Taper, Plug	82955A11	0000000

Tap and Die Sets

Use a single set for many sizes of internal and external threads. The taps and dies are for use on most metal and plastic.

Carbon Steel—Carbon steel taps are for thread repair and occasional tapping.

High-Speed Steel—High-speed steel taps and dies last longer than carbon steel when used on similar material.

Plug Chamfer—Plug-chamfer taps are a versatile choice for most tapping applications. With 3-5 chamfered cutting threads, they require moderate torque and are often used for start-to-finish tapping of through holes and closed-end holes. However, they do not start threads as easily as taper-chamfer taps. When using them to tap closed-end holes, be sure to leave sufficient space at the bottom for chips to accumulate.

Taper Chamfer—Taper-chamfer taps have 7-10 chamfered threads at the tip for cutting into the workpiece. They require less torque than other chamfer types, making them a good choice for starting threads and tapping through holes. However, a longer taper means that they cannot thread as close to the bottom of closed-end holes.

Hex—Hex-shaped dies are for thread repair and can be used with conventional wrenches.

Round—Round dies are for cutting threads. Use them with wrenches for round dies.

	Die Shape	Die Sizes Included	Wd.	Container Type	Includes		Each
Carbon Steel Taps and Dies







	Right-Hand Thread

	24	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.25 mm, M10 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	Plug, Taper	Hex	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.25 mm, M10 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	1"	Plastic Case	Die Wrench, Tap Wrench	26025A41	0000000


	40	6-32, 8-32, 10-24, 1/8"-27, 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13, M4 × 0.75 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M12 × 1.75 mm	Plug, Taper	Hex	6-32, 8-32, 10-24, 1/8"-27, 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13, M4 × 0.75 mm, M5 × 0.80 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M12 × 1.75 mm	5/8", 1"	Plastic Case	Die Wrench (2), Tap Wrench (3), Thread Gauge	2668A36	000000
	40	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	Plug, Taper	Hex	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm	5/8", 1"	Plastic Case	Die Wrench (2), Tap Wrench (3), Thread Gauge	2647A12	000000
	52	1/4"-19, 1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm	Plug, Taper	Hex	1/8"-28, 1/4"-19, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm	1", 1 7/16"	Plastic Case	Die Wrench (2), Tap Wrench (3), Thread Gauge	2726A66	000000
	65	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 1.50 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm, M20 × 2.50 mm, M22 × 1.50 mm, M24 × 2.00 mm, M24 × 3.00 mm	Plug, Taper	Hex	1/8"-28, M3 × 0.50 mm, M4 × 0.70 mm, M4 × 0.75 mm, M5 × 0.80 mm, M5 × 0.90 mm, M6 × 1.00 mm, M7 × 1.00 mm, M8 × 1.00 mm, M8 × 1.25 mm, M9 × 1.00 mm, M9 × 1.25 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.25 mm, M14 × 1.50 mm, M14 × 2.00 mm, M16 × 1.50 mm, M16 × 2.00 mm, M18 × 1.50 mm, M18 × 2.50 mm, M20 × 2.50 mm, M22 × 1.50 mm, M24 × 2.00 mm, M24 × 3.00 mm	5/8", 1", 1 3/16", 1 7/16", 1 13/16"	Plastic Case	Die Wrench (4), Tap Wrench (4), Thread Gauge	2726A68	000000


	High-Speed Steel Taps and Dies







					Right-Hand Thread

					19	M3 × 0.50 mm, M4 × 0.70 mm, M5 × 0.80 mm, M6 × 1.00 mm, M8 × 1.25 mm, M10 × 1.50 mm, M12 × 1.75 mm	Plug	Round	M3 × 0.50 mm, M4 × 0.70 mm, M5 × 0.80 mm, M6 × 1.00 mm, M8 × 1.25 mm, M10 × 1.50 mm, M12 × 1.75 mm	—	Metal Case	Die Wrench, Screwdriver, Tap Wrench (2), Thread Gauge	2646A14	000000

Tap, Die, and Thread File Sets

Repair screw threads in a wide range of sizes. The dies are hex shaped for use with conventional wrenches. The taps have a square shank that's compatible with tap wrenches and tap holders for drill presses and drilling machines. With a plug chamfer, all taps have 3-5 chamfered threads and are suitable for thread repair in both through holes and closed-end holes.

	File Sizes Included	Container Type		Each
Carbon Steel







	Right-Hand Thread

	48	1/2"-13, 1/2"-20, 1/4”-20, 1/4”-28, 3/8"-16, 3/8"-24, 5/16"-24, 5/16”-18, 7/16"-14, 7/16"-20, 9/16"-18, 9/16”-12, M6 × 1.00 mm, M8 × 1.25 mm, M10 × 1.00 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.25 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.50 mm	1/2"-13, 1/2"-20, 1/4"-20, 1/4"-28, 3/8"-16, 3/8"-24, 5/16"-18, 5/16"-24, 5/8"-11, 5/8"-18, 7/16"-14, 7/16"-20, 9/16"-12, 9/16"-18, M6 × 1.00 mm, M8 × 1.25 mm, M10 × 1.00 mm, M10 × 1.25 mm, M10 × 1.50 mm, M11 × 1.50 mm, M12 × 1.25 mm, M12 × 1.50 mm, M12 × 1.75 mm, M14 × 1.50 mm	For 0.75 to 3 mm thread pitches, For 11 to 24 threads per inch	Plastic Case	25325A15	0000000

Thread-Repairing Die Sets

Be ready for repairs by keeping a range of die sizes on hand. These dies smooth out flaws and remove dirt and rust so threads make strong connections. Don’t risk damaging threads further with an inferior quality die. Our dies are machined in the U.S. to precise dimensions for a perfect thread profile. Turn with a hex die wrench or a standard adjustable wrench.

Uncoated Carbon Steel—Hard and wear resistant for a long life, these dies work well on both metal and plastic.

	Thread Size	Thread Type	Wd.	Container Type		Each
Uncoated Carbon Steel



	7	M6, M8, M10, M12, M14, M16, M20	Metric	19/32", 11/16", 7/8", 1 1/16", 1 1/4", 1 5/8"	Plastic Case	8316A21	0000000

Dies

Rotate these dies around studs and rods to create new fastener threads. A cut above lower-quality dies that can leave inferior threads, these are machined in the U.S. to precise dimensions for accuracy and consistency.

They are adjustable, so you can cut a shallow thread that makes it easier to get the die started on the first pass. Turn the set screw to open the die to its largest diameter. Then rotate the die with a round die wrench and adjust the screw as you make additional passes to reach the proper thread size.

Uncoated High-Speed Steel—The most versatile dies stay sharp and cut cleanly, even if you use them every day. They last much longer than carbon steel dies and you won’t have to work as hard to create threads.

Titanium Nitride (TiN)-Coated High-Speed Steel—When you regularly work on challenging metals like stainless steel, choose dies with a TiN coating that reduces friction and resists heat. They turn faster and last longer than uncoated dies.

	Dies						Die Wrenches
			Uncoated High-Speed Steel		Titanium Nitride (TiN)-Coated High-Speed Steel
	Thread Size	Thread Type		Each		Each		Each
13/16" OD



		M6 × 1 mm	Metric	8294A17	000000	———	0	25565A19	00000


		1" OD



				M6 × 0.75 mm	Metric	8294A44	00000	———	0	25565A21	0000


				M6 × 1 mm	Metric	8294A21	00000	8349A51	0000000	25565A21	0000

Thread-Repairing Die Nut Sets

The dies in these sets match the width of hex nuts that are the same thread size, so one tool can turn both. For tight spaces, use with a ratcheting wrench since it requires minimal clearance to turn. Repairing dies remove imperfections and rust so threads engage properly for a strong connection.

	Thread Size	Thread Type	No. of Files	Wd., mm	Container Type		Each
Uncoated Carbon Steel



	5	M6, M7, M8, M10, M12	Metric	—	11, 14, 18, 19	Plastic Pouch	2667A32	00000


	Zinc-Plated Carbon Steel



			10	M6, M8, M10, M12	Metric	1	11, 14, 18, 19, 21	Plastic Pouch	2616A222	00000

Thread-Repairing Dies

Rescue mangled threads and return them to like-new condition. By repairing threads, you don’t have to replace the fastener or resize holes. These dies smooth out flaws and remove rust so threads engage properly and connections stay strong. Turn them with a hex die wrench or a standard adjustable wrench.

Don’t risk damaging threads further with an inferior-quality die. Our dies are machined in the U.S. to precise dimensions for a perfect thread profile.

Uncoated Carbon Steel—Hard and wear resistant for a long life, these dies work well on both metal and plastic.

			Uncoated Carbon Steel
Thread Size	Thread Type	Wd.		Each
M6 × 1 mm	Metric	19/32"	2573A72	000000

Left-Hand Dies

Make your own threads instead of searching for left-hand fasteners, which can be expensive and hard to find. A cut above lower-quality dies that can leave inferior threads, these are machined in the U.S. to precise dimensions for accuracy and consistency. They are adjustable, so you can create a shallow thread that makes it easier to get the die started on the first pass. Turn the set screw to open the die to its largest diameter. Then rotate the die with a round die wrench and adjust the screw as you make additional passes to reach the proper thread size.

	Dies				Die Wrenches
			Uncoated High-Speed Steel
	Thread Size	Thread Type		Each		Each
1" OD



		M6 × 1 mm	Metric	2596A22	000000	25565A21	00000

Thread-Repairing Die Nuts

If your wrench can turn a hex nut, it can turn these dies. They match the width of nuts of the same thread size, so you only need one tool to remove the nut, repair threads on the fastener, and put the nut back on. When space is tight, use dies with a ratcheting wrench since it requires minimal clearance to turn. Repairing dies remove imperfections and rust, resulting in threads that engage properly for a strong connection.

			Zinc-Plated Carbon Steel
Thread Size	Thread Type	Wd., mm		Each
M6 × 1 mm	Metric	11	2667A451	00000

Two-Piece Thread-Repairing Dies

Clamp the two halves of these dies around your bolt, stud, or rod to repair threads anywhere along the length. Since you don't have to spin them into place, they're often used on extra-long fasteners or when you can't access the end of your workpiece. Dies smooth damage, sharpen worn edges, and clean out rust so connections stay secure. Once in position, turn them with a hex die wrench or a standard adjustable wrench.

Black-Oxide Tool Steel—Hard and wear resistant for long life, these dies work well on both metal and plastic.

			Black-Oxide Tool Steel
Thread Size	Thread Type	Wd.		Each
M6 × 1 mm	Metric	1"	8335A62	000000

Left-Hand Thread-Repairing Dies

Repair instead of replacing left-hand fasteners, which can be expensive and hard to find. These dies correct flaws and clean out rust so the threads engage properly. Don’t risk damaging threads further with an inferior quality die. Our dies are machined in the U.S. to precise dimensions for a perfect thread profile. Turn them with a hex die wrench or a standard adjustable wrench.

Uncoated Carbon Steel—Hard and wear resistant for a long life, these dies work well on both metal and plastic.

			Uncoated Carbon Steel
Thread Size	Thread Type	Wd.		Each
M6 × 1 mm	Metric	11/16"	2573A982	000000

Thread-Repairing Flange Nuts

Clean and reshape damaged threads while fastening parts together. Similar to a die, these nuts cut through rust, residue, and weld spatter as they screw on and off to ensure strong connections and prevent sticking during assembly. They have a flange that distributes pressure evenly across the mounting surface without the need for a separate washer. Also known as collar nuts.

High-Strength Steel

Rated Grade 8, Grade G, or Class 10, these are about 25% stronger than medium-strength steel nuts. They are commonly used to fasten components in valves, pumps, and motors. To avoid stripped threads during installation, make sure your screw has a comparable strength rating.

Zinc-Flake-Coated Steel—The most durable zinc coating, zinc flake is a multilayer finish that resists wear for long-term rust protection. Similar to zinc yellow-chromate, it won't hold up to harsh chemicals like stainless steel can.

				Flange, mm
	Thread Size	Wd., mm	Ht., mm	Dia.	Thk.	Fastener Strength Grade/Class		Each
Zinc-Flake-Coated Steel



		M6 × 1 mm	10	6	14.2	1.1	Class 10	90456A110	00000